On Tue, Jan 23, 2024 at 9:39 PM Alex Williamson
<alex.williamson@xxxxxxxxxx> wrote:
>
> On Tue, 23 Jan 2024 20:59:50 +0100
> "Rafael J. Wysocki" <rafael@xxxxxxxxxx> wrote:
>
> > On Tue, Jan 23, 2024 at 8:51 PM Alex Williamson
> > <alex.williamson@xxxxxxxxxx> wrote:
> > >
> > > On Tue, 23 Jan 2024 20:40:32 +0100
> > > "Rafael J. Wysocki" <rafael@xxxxxxxxxx> wrote:
> > >
> > > > On Tue, Jan 23, 2024 at 7:56 PM Alex Williamson
> > > > <alex.williamson@xxxxxxxxxx> wrote:
> > > > >
> > > > > The commit noted in fixes added a bogus requirement that runtime PM
> > > > > managed devices need to be in the RPM_ACTIVE state for PME polling.
> > > > > In fact, only devices in low power states should be polled.
> > > > >
> > > > > However there's still a requirement that the device config space must
> > > > > be accessible, which has implications for both the current state of
> > > > > the polled device and the parent bridge, when present. It's not
> > > > > sufficient to assume the bridge remains in D0 and cases have been
> > > > > observed where the bridge passes the D0 test, but the PM state
> > > > > indicates RPM_SUSPENDING and config space of the polled device becomes
> > > > > inaccessible during pci_pme_wakeup().
> > > > >
> > > > > Therefore, since the bridge is already effectively required to be in
> > > > > the RPM_ACTIVE state, formalize this in the code and elevate the PM
> > > > > usage count to maintain the state while polling the subordinate
> > > > > device.
> > > > >
> > > > > Cc: Lukas Wunner <lukas@xxxxxxxxx>
> > > > > Cc: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
> > > > > Cc: Rafael J. Wysocki <rafael@xxxxxxxxxx>
> > > > > Fixes: d3fcd7360338 ("PCI: Fix runtime PM race with PME polling")
> > > > > Reported-by: Sanath S <sanath.s@xxxxxxx>
> > > > > Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218360
> > > > > Signed-off-by: Alex Williamson <alex.williamson@xxxxxxxxxx>
> > > > > ---
> > > > > drivers/pci/pci.c | 37 ++++++++++++++++++++++---------------
> > > > > 1 file changed, 22 insertions(+), 15 deletions(-)
> > > > >
> > > > > diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
> > > > > index bdbf8a94b4d0..764d7c977ef4 100644
> > > > > --- a/drivers/pci/pci.c
> > > > > +++ b/drivers/pci/pci.c
> > > > > @@ -2433,29 +2433,36 @@ static void pci_pme_list_scan(struct work_struct *work)
> > > > > if (pdev->pme_poll) {
> > > > > struct pci_dev *bridge = pdev->bus->self;
> > > > > struct device *dev = &pdev->dev;
> > > > > - int pm_status;
> > > > > + struct device *bdev = bridge ? &bridge->dev : NULL;
> > > > > + int bref = 0;
> > > > >
> > > > > /*
> > > > > - * If bridge is in low power state, the
> > > > > - * configuration space of subordinate devices
> > > > > - * may be not accessible
> > > > > + * If we have a bridge, it should be in an active/D0
> > > > > + * state or the configuration space of subordinate
> > > > > + * devices may not be accessible or stable over the
> > > > > + * course of the call.
> > > > > */
> > > > > - if (bridge && bridge->current_state != PCI_D0)
> > > > > - continue;
> > > > > + if (bdev) {
> > > > > + bref = pm_runtime_get_if_active(bdev, true);
> > > > > + if (!bref)
> > > >
> > > > I would check bref <= 0 here.
> > > >
> > > > > + continue;
> > > > > +
> > > > > + if (bridge->current_state != PCI_D0)
> > > >
> > > > Isn't the power state guaranteed to be PCI_D0 at this point? If it
> > > > isn't, then why?
> > >
> > > Both of these seem necessary to support !CONFIG_PM, where bref would be
> > > -EINVAL and provides no indication of the current_state. Is that
> > > incorrect? Thanks,
> >
> > Well, CONFIG_PCIE_PME depends on CONFIG_PM, so I'm not sure how
> > dev->pme_poll can be set without it.
>
> I only see that drivers/pci/pci.c:pci_pm_init() sets pme_poll true and
> I'm not spotting a dependency on either PCIE_PME or PM to get there. I
> see a few places where pme.c, governed by PCIE_PME, can set pme_poll
> false though.
All of this is a bit moot when CONFIG_PM is unset, because PME polling
was introduced as a workaround for problems with PME signaling which
is only enabled when CONFIG_PM is set. IOW, if CONFIG_PM is not set,
there is no reason for PME polling.
> It's also not clear to me that we should skip scanning a device if
> pm_runtime_get_if_active() returns -EINVAL for the bridge due to
> power.disable_depth.
Let me recap things a bit.
PME polling is run from a freezable workqueue, so it is not carried
out during system-wide PM transitions, only in the working state
proper.
This means that when runtime PM is disabled for a bridge, there is no
reason for its power state to change and all bridges start in D0.
So you are right, the endpoint device below the bridge still needs to
be scanned then, but I'm not sure about the current_state check. In
theory, it should not be necessary.
But I agree that this is a minor point, so please feel free to add
Reviewed-by: Rafael J. Wysocki <rafael@xxxxxxxxxx>
to the patch.
