Re: [RFC PATCH v10 4/5] iommu/vt-d: don't issue ATS Invalidation request when device is disconnected

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 1/10/2024 1:24 PM, Baolu Lu wrote:
On 12/29/23 1:05 AM, Ethan Zhao wrote:
Except those aggressive hotplug cases - surprise remove a hotplug device
while its safe removal is requested and handled in process by:

1. pull it out directly.
2. turn off its power.
3. bring the link down.
4. just died there that moment.

etc, in a word, 'gone' or 'disconnected'.

Mostly are regular normal safe removal and surprise removal unplug.
these hot unplug handling process could be optimized for fix the ATS
Invalidation hang issue by calling pci_dev_is_disconnected() in function
devtlb_invalidation_with_pasid() to check target device state to avoid
sending meaningless ATS Invalidation request to iommu when device is gone.
(see IMPLEMENTATION NOTE in PCIe spec r6.1 section 10.3.1)

For safe removal, device wouldn't be removed untill the whole software
handling process is done, it wouldn't trigger the hard lock up issue
caused by too long ATS Invalidation timeout wait. In safe removal path,
device state isn't set to pci_channel_io_perm_failure in
pciehp_unconfigure_device() by checking 'presence' parameter, calling
pci_dev_is_disconnected() in devtlb_invalidation_with_pasid() will return
false there, wouldn't break the function.

For surprise removal, device state is set to pci_channel_io_perm_failure in
pciehp_unconfigure_device(), means device is already gone (disconnected)
call pci_dev_is_disconnected() in devtlb_invalidation_with_pasid() will
return true to break the function not to send ATS Invalidation request to the disconnected device blindly, thus avoid the further long time waiting
triggers the hard lockup.

safe removal & surprise removal

pciehp_ist()
    pciehp_handle_presence_or_link_change()
      pciehp_disable_slot()
        remove_board()
          pciehp_unconfigure_device(presence)

Tested-by: Haorong Ye <yehaorong@xxxxxxxxxxxxx>
Signed-off-by: Ethan Zhao <haifeng.zhao@xxxxxxxxxxxxxxx>
---
  drivers/iommu/intel/pasid.c | 2 ++
  1 file changed, 2 insertions(+)

diff --git a/drivers/iommu/intel/pasid.c b/drivers/iommu/intel/pasid.c
index 715943531091..3d5ed27f39ef 100644
--- a/drivers/iommu/intel/pasid.c
+++ b/drivers/iommu/intel/pasid.c
@@ -480,6 +480,8 @@ devtlb_invalidation_with_pasid(struct intel_iommu *iommu,
      if (!info || !info->ats_enabled)
          return;
  +    if (pci_dev_is_disconnected(to_pci_dev(dev)))
+        return;

Why do you need the above after changes in PATCH 2/5? It's unnecessary
and not complete. We have other places where device TLB invalidation is
issued, right?

This one could be regarded as optimization, no need to trapped into rabbit

hole if we could predict the result. because the bad thing is we don't know

what response to us in the rabbit hole from third party switch (bridges will

feedback timeout to requester as PCIe spec mentioned if the endpoint is

gone).


Thanks,

Ethan


      /*
       * When PASID 0 is used, it indicates RID2PASID(DMA request w/o PASID),
       * devTLB flush w/o PASID should be used. For non-zero PASID under

Best regards,
baolu




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux