Re: [PATCH V3 4/6] arm64: dts: qcom: ipq9574: Add PCIe PHYs and controller nodes

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, 21 Apr 2023 at 15:50, Devi Priya <quic_devipriy@xxxxxxxxxxx> wrote:
>
> Add PCIe0, PCIe1, PCIe2, PCIe3 (and corresponding PHY) devices
> found on IPQ9574 platform. The PCIe0 & PCIe1 are 1-lane Gen3
> host whereas PCIe2 & PCIe3 are 2-lane Gen3 host.
>
> Co-developed-by: Anusha Rao <quic_anusha@xxxxxxxxxxx>
> Signed-off-by: Anusha Rao <quic_anusha@xxxxxxxxxxx>
> Signed-off-by: Devi Priya <quic_devipriy@xxxxxxxxxxx>
> ---
>  Changes in V3:
>         - Fixed up the PCI I/O port ranges
>
>  arch/arm64/boot/dts/qcom/ipq9574.dtsi | 375 +++++++++++++++++++++++++-
>  1 file changed, 370 insertions(+), 5 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> index e757b57957cf..953a839a1141 100644
> --- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
> @@ -6,8 +6,8 @@
>   * Copyright (c) 2023, Qualcomm Innovation Center, Inc. All rights reserved.
>   */
>
> -#include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/clock/qcom,ipq9574-gcc.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/reset/qcom,ipq9574-gcc.h>
>
>  / {
> @@ -116,6 +116,58 @@
>                 #size-cells = <1>;
>                 ranges = <0 0 0 0xffffffff>;
>
> +               pcie0_phy: phy@84000 {
> +                       compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> +                       reg = <0x00084000 0x1000>;
> +
> +                       clocks = <&gcc GCC_PCIE0_AUX_CLK>,
> +                                <&gcc GCC_PCIE0_AHB_CLK>,
> +                                <&gcc GCC_ANOC_PCIE0_1LANE_M_CLK>,
> +                                <&gcc GCC_SNOC_PCIE0_1LANE_S_CLK>,
> +                                <&gcc GCC_PCIE0_PIPE_CLK>;
> +                       clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
> +
> +                       assigned-clocks = <&gcc GCC_PCIE0_AUX_CLK>;
> +                       assigned-clock-rates = <20000000>;
> +
> +                       resets = <&gcc GCC_PCIE0_PHY_BCR>,
> +                                <&gcc GCC_PCIE0PHY_PHY_BCR>;
> +                       reset-names = "phy", "common";
> +
> +                       #clock-cells = <0>;
> +                       clock-output-names = "gcc_pcie0_pipe_clk_src";
> +
> +                       #phy-cells = <0>;
> +                       status = "disabled";
> +
> +               };
> +
> +               pcie2_phy: phy@8c000 {
> +                       compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> +                       reg = <0x0008c000 0x2000>;
> +
> +                       clocks = <&gcc GCC_PCIE2_AUX_CLK>,
> +                                <&gcc GCC_PCIE2_AHB_CLK>,
> +                                <&gcc GCC_ANOC_PCIE2_2LANE_M_CLK>,
> +                                <&gcc GCC_SNOC_PCIE2_2LANE_S_CLK>,
> +                                <&gcc GCC_PCIE2_PIPE_CLK>;
> +                       clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
> +
> +                       assigned-clocks = <&gcc GCC_PCIE2_AUX_CLK>;
> +                       assigned-clock-rates = <20000000>;
> +
> +                       resets = <&gcc GCC_PCIE2_PHY_BCR>,
> +                                <&gcc GCC_PCIE2PHY_PHY_BCR>;
> +                       reset-names = "phy", "common";
> +
> +                       #clock-cells = <0>;
> +                       clock-output-names = "gcc_pcie2_pipe_clk_src";
> +
> +                       #phy-cells = <0>;
> +                       status = "disabled";
> +
> +               };
> +
>                 rng: rng@e3000 {
>                         compatible = "qcom,prng-ee";
>                         reg = <0x000e3000 0x1000>;
> @@ -123,6 +175,58 @@
>                         clock-names = "core";
>                 };
>
> +               pcie3_phy: phy@f4000 {
> +                       compatible = "qcom,ipq9574-qmp-gen3x2-pcie-phy";
> +                       reg = <0x000f4000 0x2000>;
> +
> +                       clocks = <&gcc GCC_PCIE3_AUX_CLK>,
> +                                <&gcc GCC_PCIE3_AHB_CLK>,
> +                                <&gcc GCC_ANOC_PCIE3_2LANE_M_CLK>,
> +                                <&gcc GCC_SNOC_PCIE3_2LANE_S_CLK>,
> +                                <&gcc GCC_PCIE3_PIPE_CLK>;
> +                       clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
> +
> +                       assigned-clocks = <&gcc GCC_PCIE3_AUX_CLK>;
> +                       assigned-clock-rates = <20000000>;
> +
> +                       resets = <&gcc GCC_PCIE3_PHY_BCR>,
> +                                <&gcc GCC_PCIE3PHY_PHY_BCR>;
> +                       reset-names = "phy", "common";
> +
> +                       #clock-cells = <0>;
> +                       clock-output-names = "gcc_pcie3_pipe_clk_src";
> +
> +                       #phy-cells = <0>;
> +                       status = "disabled";
> +
> +               };
> +
> +               pcie1_phy: phy@fc000 {
> +                       compatible = "qcom,ipq9574-qmp-gen3x1-pcie-phy";
> +                       reg = <0x000fc000 0x1000>;
> +
> +                       clocks = <&gcc GCC_PCIE1_AUX_CLK>,
> +                                <&gcc GCC_PCIE1_AHB_CLK>,
> +                                <&gcc GCC_ANOC_PCIE1_1LANE_M_CLK>,
> +                                <&gcc GCC_SNOC_PCIE1_1LANE_S_CLK>,
> +                                <&gcc GCC_PCIE1_PIPE_CLK>;
> +                       clock-names = "aux", "cfg_ahb", "anoc_lane", "snoc_lane", "pipe";
> +
> +                       assigned-clocks = <&gcc GCC_PCIE1_AUX_CLK>;
> +                       assigned-clock-rates = <20000000>;
> +
> +                       resets = <&gcc GCC_PCIE1_PHY_BCR>,
> +                                <&gcc GCC_PCIE1PHY_PHY_BCR>;
> +                       reset-names = "phy", "common";
> +
> +                       #clock-cells = <0>;
> +                       clock-output-names = "gcc_pcie1_pipe_clk_src";
> +
> +                       #phy-cells = <0>;
> +                       status = "disabled";
> +
> +               };
> +
>                 tlmm: pinctrl@1000000 {
>                         compatible = "qcom,ipq9574-tlmm";
>                         reg = <0x01000000 0x300000>;
> @@ -146,10 +250,10 @@
>                         reg = <0x01800000 0x80000>;
>                         clocks = <&xo_board_clk>,
>                                  <&sleep_clk>,
> -                                <0>,
> -                                <0>,
> -                                <0>,
> -                                <0>,
> +                                <&pcie0_phy>,
> +                                <&pcie1_phy>,
> +                                <&pcie2_phy>,
> +                                <&pcie3_phy>,
>                                  <0>;
>                         #clock-cells = <1>;
>                         #reset-cells = <1>;
> @@ -478,6 +582,267 @@
>                                 status = "disabled";
>                         };
>                 };
> +
> +               pcie1: pci@10000000 {
> +                       compatible = "qcom,pcie-ipq9574";
> +                       reg =  <0x10000000 0xf1d>,
> +                              <0x10000F20 0xa8>,
> +                              <0x10001000 0x1000>,
> +                              <0x000F8000 0x4000>,
> +                              <0x10100000 0x1000>;
> +                       reg-names = "dbi", "elbi", "atu", "parf", "config";
> +                       device_type = "pci";
> +                       linux,pci-domain = <2>;
> +                       bus-range = <0x00 0xff>;
> +                       num-lanes = <1>;
> +                       #address-cells = <3>;
> +                       #size-cells = <2>;
> +
> +                       ranges = <0x01000000 0x0 0x00000000 0x10200000 0x0 0x100000>,  /* I/O */
> +                                <0x02000000 0x0 0x10300000 0x10300000 0x0 0x7d00000>; /* MEM */
> +
> +                       #interrupt-cells = <1>;
> +                       interrupt-map-mask = <0 0 0 0x7>;
> +                       interrupt-map = <0 0 0 1 &intc 0 35 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> +                                       <0 0 0 2 &intc 0 49 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +                                       <0 0 0 3 &intc 0 84 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +                                       <0 0 0 4 &intc 0 85 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +

No iommu-map?

> +                       interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> +                       interrupt-names = "global_irq";
> +
> +                       /* clocks and clock-names are used to enable the clock in CBCR */
> +                       clocks = <&gcc GCC_PCIE1_AHB_CLK>,
> +                                <&gcc GCC_PCIE1_AUX_CLK>,
> +                                <&gcc GCC_PCIE1_AXI_M_CLK>,
> +                                <&gcc GCC_PCIE1_AXI_S_CLK>,
> +                                <&gcc GCC_PCIE1_AXI_S_BRIDGE_CLK>,
> +                                <&gcc GCC_PCIE1_RCHNG_CLK>;
> +                       clock-names = "ahb",
> +                                     "aux",
> +                                     "axi_m",
> +                                     "axi_s",
> +                                     "axi_bridge",
> +                                     "rchng";
> +
> +                       resets = <&gcc GCC_PCIE1_PIPE_ARES>,
> +                                <&gcc GCC_PCIE1_CORE_STICKY_ARES>,
> +                                <&gcc GCC_PCIE1_AXI_S_STICKY_ARES>,
> +                                <&gcc GCC_PCIE1_AXI_S_ARES>,
> +                                <&gcc GCC_PCIE1_AXI_M_STICKY_ARES>,
> +                                <&gcc GCC_PCIE1_AXI_M_ARES>,
> +                                <&gcc GCC_PCIE1_AUX_ARES>,
> +                                <&gcc GCC_PCIE1_AHB_ARES>;
> +                       reset-names = "pipe",
> +                                     "sticky",
> +                                     "axi_s_sticky",
> +                                     "axi_s",
> +                                     "axi_m_sticky",
> +                                     "axi_m",
> +                                     "aux",
> +                                     "ahb";
> +
> +                       phys = <&pcie1_phy>;
> +                       phy-names = "pciephy";
> +                       msi-parent = <&v2m0>;
> +                       status = "disabled";
> +               };
> +
> +               pcie3: pci@18000000 {
> +                       compatible = "qcom,pcie-ipq9574";
> +                       reg =  <0x18000000 0xf1d>,
> +                              <0x18000F20 0xa8>,
> +                              <0x18001000 0x1000>,
> +                              <0x000F0000 0x4000>,
> +                              <0x18100000 0x1000>;
> +                       reg-names = "dbi", "elbi", "atu", "parf", "config";
> +                       device_type = "pci";
> +                       linux,pci-domain = <4>;
> +                       bus-range = <0x00 0xff>;
> +                       num-lanes = <2>;
> +                       #address-cells = <3>;
> +                       #size-cells = <2>;
> +
> +                       ranges = <0x01000000 0x0 0x00000000 0x18200000 0x0 0x100000>,  /* I/O */
> +                                <0x02000000 0x0 0x18300000 0x18300000 0x0 0x7d00000>; /* MEM */
> +
> +                       #interrupt-cells = <1>;
> +                       interrupt-map-mask = <0 0 0 0x7>;
> +                       interrupt-map = <0 0 0 1 &intc 0 189 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> +                                       <0 0 0 2 &intc 0 190 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +                                       <0 0 0 3 &intc 0 191 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +                                       <0 0 0 4 &intc 0 192 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
> +                       interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
> +                       interrupt-names = "global_irq";
> +
> +                       /* clocks and clock-names are used to enable the clock in CBCR */
> +                       clocks = <&gcc GCC_PCIE3_AHB_CLK>,
> +                                <&gcc GCC_PCIE3_AUX_CLK>,
> +                                <&gcc GCC_PCIE3_AXI_M_CLK>,
> +                                <&gcc GCC_PCIE3_AXI_S_CLK>,
> +                                <&gcc GCC_PCIE3_AXI_S_BRIDGE_CLK>,
> +                                <&gcc GCC_PCIE3_RCHNG_CLK>;
> +                       clock-names = "ahb",
> +                                     "aux",
> +                                     "axi_m",
> +                                     "axi_s",
> +                                     "axi_bridge",
> +                                     "rchng";
> +
> +                       resets = <&gcc GCC_PCIE3_PIPE_ARES>,
> +                                <&gcc GCC_PCIE3_CORE_STICKY_ARES>,
> +                                <&gcc GCC_PCIE3_AXI_S_STICKY_ARES>,
> +                                <&gcc GCC_PCIE3_AXI_S_ARES>,
> +                                <&gcc GCC_PCIE3_AXI_M_STICKY_ARES>,
> +                                <&gcc GCC_PCIE3_AXI_M_ARES>,
> +                                <&gcc GCC_PCIE3_AUX_ARES>,
> +                                <&gcc GCC_PCIE3_AHB_ARES>;
> +                       reset-names = "pipe",
> +                                     "sticky",
> +                                     "axi_s_sticky",
> +                                     "axi_s",
> +                                     "axi_m_sticky",
> +                                     "axi_m",
> +                                     "aux",
> +                                     "ahb";
> +
> +                       phys = <&pcie3_phy>;
> +                       phy-names = "pciephy";
> +                       msi-parent = <&v2m0>;
> +                       status = "disabled";
> +               };
> +
> +               pcie2: pci@20000000 {
> +                       compatible = "qcom,pcie-ipq9574";
> +                       reg =  <0x20000000 0xf1d>,
> +                              <0x20000F20 0xa8>,
> +                              <0x20001000 0x1000>,
> +                              <0x00088000 0x4000>,
> +                              <0x20100000 0x1000>;
> +                       reg-names = "dbi", "elbi", "atu", "parf", "config";
> +                       device_type = "pci";
> +                       linux,pci-domain = <3>;
> +                       bus-range = <0x00 0xff>;
> +                       num-lanes = <2>;
> +                       #address-cells = <3>;
> +                       #size-cells = <2>;
> +
> +                       ranges = <0x01000000 0x0 0x00000000 0x20200000 0x0 0x100000>,  /* I/O */
> +                                <0x02000000 0x0 0x20300000 0x20300000 0x0 0x7d00000>; /* MEM */
> +
> +                       #interrupt-cells = <1>;
> +                       interrupt-map-mask = <0 0 0 0x7>;
> +                       interrupt-map = <0 0 0 1 &intc 0 164 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> +                                       <0 0 0 2 &intc 0 165 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +                                       <0 0 0 3 &intc 0 186 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +                                       <0 0 0 4 &intc 0 187 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
> +                       interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
> +                       interrupt-names = "global_irq";
> +
> +                       /* clocks and clock-names are used to enable the clock in CBCR */
> +                       clocks = <&gcc GCC_PCIE2_AHB_CLK>,
> +                                <&gcc GCC_PCIE2_AUX_CLK>,
> +                                <&gcc GCC_PCIE2_AXI_M_CLK>,
> +                                <&gcc GCC_PCIE2_AXI_S_CLK>,
> +                                <&gcc GCC_PCIE2_AXI_S_BRIDGE_CLK>,
> +                                <&gcc GCC_PCIE2_RCHNG_CLK>;
> +                       clock-names = "ahb",
> +                                     "aux",
> +                                     "axi_m",
> +                                     "axi_s",
> +                                     "axi_bridge",
> +                                     "rchng";
> +
> +                       resets = <&gcc GCC_PCIE2_PIPE_ARES>,
> +                                <&gcc GCC_PCIE2_CORE_STICKY_ARES>,
> +                                <&gcc GCC_PCIE2_AXI_S_STICKY_ARES>,
> +                                <&gcc GCC_PCIE2_AXI_S_ARES>,
> +                                <&gcc GCC_PCIE2_AXI_M_STICKY_ARES>,
> +                                <&gcc GCC_PCIE2_AXI_M_ARES>,
> +                                <&gcc GCC_PCIE2_AUX_ARES>,
> +                                <&gcc GCC_PCIE2_AHB_ARES>;
> +                       reset-names = "pipe",
> +                                     "sticky",
> +                                     "axi_s_sticky",
> +                                     "axi_s",
> +                                     "axi_m_sticky",
> +                                     "axi_m",
> +                                     "aux",
> +                                     "ahb";
> +
> +                       phys = <&pcie2_phy>;
> +                       phy-names = "pciephy";
> +                       msi-parent = <&v2m0>;
> +                       status = "disabled";
> +               };
> +
> +               pcie0: pci@28000000 {
> +                       compatible = "qcom,pcie-ipq9574";
> +                       reg =  <0x28000000 0xf1d>,
> +                              <0x28000F20 0xa8>,
> +                              <0x28001000 0x1000>,
> +                              <0x00080000 0x4000>,
> +                              <0x28100000 0x1000>;
> +                       reg-names = "dbi", "elbi", "atu", "parf", "config";
> +                       device_type = "pci";
> +                       linux,pci-domain = <1>;
> +                       bus-range = <0x00 0xff>;
> +                       num-lanes = <1>;
> +                       #address-cells = <3>;
> +                       #size-cells = <2>;
> +
> +                       ranges = <0x01000000 0x0 0x00000000 0x28200000 0x0 0x100000>,  /* I/O */
> +                                <0x02000000 0x0 0x28300000 0x28300000 0x0 0x7d00000>; /* MEM */
> +
> +                       #interrupt-cells = <1>;
> +                       interrupt-map-mask = <0 0 0 0x7>;
> +                       interrupt-map = <0 0 0 1 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> +                                       <0 0 0 2 &intc 0 78 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +                                       <0 0 0 3 &intc 0 79 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +                                       <0 0 0 4 &intc 0 83 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +
> +                       interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
> +                       interrupt-names = "global_irq";
> +
> +                       /* clocks and clock-names are used to enable the clock in CBCR */
> +                       clocks = <&gcc GCC_PCIE0_AHB_CLK>,
> +                                <&gcc GCC_PCIE0_AUX_CLK>,
> +                                <&gcc GCC_PCIE0_AXI_M_CLK>,
> +                                <&gcc GCC_PCIE0_AXI_S_CLK>,
> +                                <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
> +                                <&gcc GCC_PCIE0_RCHNG_CLK>;
> +                       clock-names = "ahb",
> +                                     "aux",
> +                                     "axi_m",
> +                                     "axi_s",
> +                                     "axi_bridge",
> +                                     "rchng";
> +
> +                       resets = <&gcc GCC_PCIE0_PIPE_ARES>,
> +                                <&gcc GCC_PCIE0_CORE_STICKY_ARES>,
> +                                <&gcc GCC_PCIE0_AXI_S_STICKY_ARES>,
> +                                <&gcc GCC_PCIE0_AXI_S_ARES>,
> +                                <&gcc GCC_PCIE0_AXI_M_STICKY_ARES>,
> +                                <&gcc GCC_PCIE0_AXI_M_ARES>,
> +                                <&gcc GCC_PCIE0_AUX_ARES>,
> +                                <&gcc GCC_PCIE0_AHB_ARES>;
> +                       reset-names = "pipe",
> +                                     "sticky",
> +                                     "axi_s_sticky",
> +                                     "axi_s",
> +                                     "axi_m_sticky",
> +                                     "axi_m",
> +                                     "aux",
> +                                     "ahb";
> +
> +                       phys = <&pcie0_phy>;
> +                       phy-names = "pciephy";
> +                       msi-parent = <&v2m0>;
> +                       status = "disabled";
> +               };
> +
>         };
>
>         timer {
> --
> 2.17.1
>


-- 
With best wishes
Dmitry



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux