On Mon, Sep 26, 2022 at 08:34:30PM +0300, Dmitry Baryshkov wrote: > Programming of QMP PCIe PHYs slightly differs between RC and EP modes. > > Currently both qcom and qcom-ep PCIe controllers setup the PHY in the > default mode, making it impossible to select at runtime whether the PHY > should be running in RC or in EP modes. Usually this is not an issue, > since for most devices only the RC mode is used. Some devices (SDX55) > currently support only the EP mode without supporting the RC mode (at > this moment). > > Nevertheless some of the Qualcomm platforms (e.g. the aforementioned > SDX55) would still benefit from being able to switch between RC and EP > depending on the driver being used. While it is possible to use > different compat strings for the PHY depending on the mode, it seems > like an incorrect approach, since the PHY doesn't differ between > usecases. It's the PCIe controller, who should decide how to configure > the PHY. > > This patch series implements the ability to select between RC and EP > modes, by allowing the PCIe QMP PHY driver to switch between > programming tables. > > This patchseries depends on the header from the pre-6.1 phy/next. Thus > after the 6.1 the PCIe patches can be applied independently of the PHY > part. I assume then it is better for me to ACK the PCI patches so that they can be pulled into the PHY tree, right ? Lorenzo > Changes since v4: > - Fixed the possible oops in probe (Johan) > - Renamed the tables struct and individual table fields (Johan) > - Squashed the 'separate funtions' patch to lower the possible > confusion. > > Changes since v3: > - Rebased on top of phy/next to pick in newly defined > PHY_MODE_PCIE_RC/EP. > - Renamed 'main' to 'common' and 'secondary' to 'extra' to reflect the > intention of the split (the 'common' tables and the 'extra for the ... > mode' tables). > - Merged the 'pointer' patch into first and second patches to make them > more obvious. > > Changes since v2: > - Added PHY_SUBMODE_PCIE_RC/EP defines (Vinod), > - Changed `primary' table name to `main', added extra comments > describing that `secondary' are the additional tables, not required in > most of the cases (following the suggestion by Johan to rename > `primary' table), > - Changed secondary tables into the pointers to stop wasting extra > memory (Vinod), > - Split several functions for programming the PHY using these tables. > > Changes since v1: > - Split the if(table) removal to the separate patch > - Expanded commit messages and comments to provide additional details > - Fixed build error on pcie-qcom.c > - Added support for EP mode on sm8450 to demonstrate the usage of this > patchset > > Changes since RFC: > - Fixed the compilation of PCIe EP driver, > - Changed pri/sec names to primary and secondary, > - Added comments regarding usage of secondary_rc/_ep fields. > > Dmitry Baryshkov (5): > phy: qcom-qmp-pcie: split register tables into common and extra parts > phy: qcom-qmp-pcie: support separate tables for EP mode > phy: qcom-qmp-pcie: Support SM8450 PCIe1 PHY in EP mode > PCI: qcom: Setup PHY to work in RC mode > PCI: qcom-ep: Setup PHY to work in EP mode > > drivers/pci/controller/dwc/pcie-qcom-ep.c | 5 + > drivers/pci/controller/dwc/pcie-qcom.c | 5 + > drivers/phy/qualcomm/phy-qcom-qmp-pcie.c | 523 +++++++++++------- > .../qualcomm/phy-qcom-qmp-pcs-pcie-v5_20.h | 1 + > 4 files changed, 335 insertions(+), 199 deletions(-) > > -- > 2.35.1 >
