[PATCH v5 0/5] PCI: qcom: Support using the same PHY for both RC and EP

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Programming of QMP PCIe PHYs slightly differs between RC and EP modes.

Currently both qcom and qcom-ep PCIe controllers setup the PHY in the
default mode, making it impossible to select at runtime whether the PHY
should be running in RC or in EP modes. Usually this is not an issue,
since for most devices only the RC mode is used. Some devices (SDX55)
currently support only the EP mode without supporting the RC mode (at
this moment).

Nevertheless some of the Qualcomm platforms (e.g. the aforementioned
SDX55) would still benefit from being able to switch between RC and EP
depending on the driver being used. While it is possible to use
different compat strings for the PHY depending on the mode, it seems
like an incorrect approach, since the PHY doesn't differ between
usecases. It's the PCIe controller, who should decide how to configure
the PHY.

This patch series implements the ability to select between RC and EP
modes, by allowing the PCIe QMP PHY driver to switch between
programming tables.

This patchseries depends on the header from the pre-6.1 phy/next. Thus
after the 6.1 the PCIe patches can be applied independently of the PHY
part.

Changes since v4:
- Fixed the possible oops in probe (Johan)
- Renamed the tables struct and individual table fields (Johan)
- Squashed the 'separate funtions' patch to lower the possible
  confusion.

Changes since v3:
- Rebased on top of phy/next to pick in newly defined
  PHY_MODE_PCIE_RC/EP.
- Renamed 'main' to 'common' and 'secondary' to 'extra' to reflect the
  intention of the split (the 'common' tables and the 'extra for the ...
  mode' tables).
- Merged the 'pointer' patch into first and second patches to make them
  more obvious.

Changes since v2:
- Added PHY_SUBMODE_PCIE_RC/EP defines (Vinod),
- Changed `primary' table name to `main', added extra comments
  describing that `secondary' are the additional tables, not required in
  most of the cases (following the suggestion by Johan to rename
  `primary' table),
- Changed secondary tables into the pointers to stop wasting extra
  memory (Vinod),
- Split several functions for programming the PHY using these tables.

Changes since v1:
- Split the if(table) removal to the separate patch
- Expanded commit messages and comments to provide additional details
- Fixed build error on pcie-qcom.c
- Added support for EP mode on sm8450 to demonstrate the usage of this
  patchset

Changes since RFC:
- Fixed the compilation of PCIe EP driver,
- Changed pri/sec names to primary and secondary,
- Added comments regarding usage of secondary_rc/_ep fields.

Dmitry Baryshkov (5):
  phy: qcom-qmp-pcie: split register tables into common and extra parts
  phy: qcom-qmp-pcie: support separate tables for EP mode
  phy: qcom-qmp-pcie: Support SM8450 PCIe1 PHY in EP mode
  PCI: qcom: Setup PHY to work in RC mode
  PCI: qcom-ep: Setup PHY to work in EP mode

 drivers/pci/controller/dwc/pcie-qcom-ep.c     |   5 +
 drivers/pci/controller/dwc/pcie-qcom.c        |   5 +
 drivers/phy/qualcomm/phy-qcom-qmp-pcie.c      | 523 +++++++++++-------
 .../qualcomm/phy-qcom-qmp-pcs-pcie-v5_20.h    |   1 +
 4 files changed, 335 insertions(+), 199 deletions(-)

-- 
2.35.1




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux