On Saturday 06 August 2022 17:46:14 Manivannan Sadhasivam wrote: > On Sat, Aug 06, 2022 at 01:17:02PM +0200, Pali Rohár wrote: > > On Saturday 06 August 2022 16:36:13 Manivannan Sadhasivam wrote: > > > Hi Pali, > > > > > > On Mon, Jul 11, 2022 at 12:51:08AM +0200, Pali Rohár wrote: > > > > Hello! > > > > > > > > Together with Mauri we are working on extending pci-mvebu.c driver to > > > > support Orion PCIe controllers as these controllers are same as mvebu > > > > controller. > > > > > > > > There is just one big difference: Config space access on Orion is > > > > different. mvebu uses classic Intel CFC/CF8 registers for indirect > > > > config space access but Orion has direct memory mapped config space. > > > > So Orion DTS files need to have this memory range for config space and > > > > pci-mvebu.c driver have to read this range from DTS and properly map it. > > > > > > > > So my question is: How to properly define config space range in device > > > > tree file? In which device tree property and in which format? Please > > > > note that this memory range of config space is PCIe root port specific > > > > and it requires its own MBUS_ID() like memory range of PCIe MEM and PCIe > > > > IO mapping. Please look e.g. at armada-385.dtsi how are MBUS_ID() used: > > > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/armada-385.dtsi > > > > > > > > > > On most of the platforms, the standard "reg" property is used to specify the > > > config space together with other device specific memory regions. For instance, > > > on the Qcom platforms based on Designware IP, we have below regions: > > > > > > reg = <0xfc520000 0x2000>, > > > <0xff000000 0x1000>, > > > <0xff001000 0x1000>, > > > <0xff002000 0x2000>; > > > reg-names = "parf", "dbi", "elbi", "config"; > > > > > > Where "parf" and "elbi" are Qcom controller specific regions, while "dbi" and > > > "config" (config space) are common to all Designware IPs. > > > > > > These properties are documented in: Documentation/devicetree/bindings/pci/qcom,pcie.yaml > > > > > > Hope this helps! > > > > Hello! I have already looked at this. But as I pointed in above > > armada-385.dtsi file, mvebu is quite complicated. First it does not use > > explicit address ranges, but rather macros MBUS_ID() which assign > > addresses at kernel runtime by mbus driver. Second issue is that config > > space range (like any other resources) are pcie root port specific. So > > it cannot be in pcie controller node and in pcie devices is "reg" > > property reserved for pci bdf address. > > > > In last few days, I spent some time on this issue and after reading lot > > of pcie dts files, including bindings and other documents (including > > open firmware pci2_1.pdf) and I'm proposing following definition: > > > > soc { > > pcie-mem-aperture = <0xe0000000 0x08000000>; /* 128 MiB memory space */ > > pcie-cfg-aperture = <0xf0000000 0x01000000>; /* 16 MiB config space */ > > pcie-io-aperture = <0xf2000000 0x00100000>; /* 1 MiB I/O space */ > > > > pcie { > > ranges = <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0x0 0x2000>, /* Port 0.0 Internal registers */ > > <0x82000000 0 0xf0000000 MBUS_ID(0x04, 0x79) 0 0x0 0x1000000>, /* Port 0.0 Config space */ > > <0x82000000 1 0x0 MBUS_ID(0x04, 0x59) 0 0x1 0x0>, /* Port 0.0 Mem */ > > <0x81000000 1 0x0 MBUS_ID(0x04, 0x51) 0 0x1 0x0>, /* Port 0.0 I/O */ > > > > pcie@1,0 { > > reg = <0x0800 0 0 0 0>; /* BDF 0:1.0 */ > > assigned-addresses = <0x82000800 0 0x40000 0x0 0x2000>, /* Port 0.0 Internal registers */ > > <0x82000800 0 0xf0000000 0x0 0x1000000>; /* Port 0.0 Config space */ > > ranges = <0x82000000 0 0 0x82000000 1 0 0x1 0x0>, /* Port 0.0 Mem */ > > 0x81000000 0 0 0x81000000 1 0 0x1 0x0>; /* Port 0.0 I/O */ > > }; > > }; > > }; > > > > So the pci config space address range would be defined in > > "assigned-addresses" property as the _second_ value. First value is > > already used for specifying internal registers (similar what is "parf" > > for qcom). > > > > Sounds reasonable to me. Another option would be to introduce a mvebu specific > property but that would be the least preferred option I guess. > > But the fact that "assigned-addresses" property is described as "MMIO registers" > also adds up to the justification IMO. > > Rob/Krzysztof could always correct that during binding review. Ok! > > config space is currently limited to 16 MB (without extended PCIe), but > > after we find free continuous physical address window of size 256MB we > > can extend it to full PCIe config space range. > > > > Any objections to above device tree definition? > > > > Are you also converting the binding to YAML for validation? I still have an issue to understand YAML scheme declaration and do not know how to express all those properties in this scheme language correctly. Also I was not able to setup infrastructure for running scheme binding tests. So I'm currently not planning to do this. It would be really a good idea to provide some web service where people could upload their work-in-progress DTS files and YAML schemes for automatic validation. > Thanks, > Mani > > > > Thanks, > > > Mani > > > > > > > Krzysztof, would you be able to help with proper definition of this > > > > property, so it would be fine also for schema checkers or other > > > > automatic testing tools? > > > > > > -- > > > மணிவண்ணன் சதாசிவம் > > -- > மணிவண்ணன் சதாசிவம்