Re: [PATCH v7 3/3] PCI: qcom: Add IPQ60xx support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, Jun 12, 2022 at 01:18:35PM +0300, Baruch Siach wrote:
> From: Selvam Sathappan Periakaruppan <quic_speriaka@xxxxxxxxxxx>
> 
> IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
> platform.
> 
> The code is based on downstream[1] Codeaurora kernel v5.4 (branch
> win.linuxopenwrt.2.0).
> 
> Split out the DBI registers access part from .init into .post_init. DBI
> registers are only accessible after phy_power_on().
> 
> [1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
> 
> Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@xxxxxxxxxxxxxx>
> Signed-off-by: Baruch Siach <baruch.siach@xxxxxxxxx>
> ---

> +static void qcom_pcie_deinit_2_9_0(struct qcom_pcie *pcie)
> +{
> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> +
> +	clk_bulk_disable_unprepare(ARRAY_SIZE(res->clks), res->clks);

Assert reset as you do in the init error path?

> +}
> +
> +static int qcom_pcie_init_2_9_0(struct qcom_pcie *pcie)
> +{
> +	struct qcom_pcie_resources_2_9_0 *res = &pcie->res.v2_9_0;
> +	struct device *dev = pcie->pci->dev;
> +	int ret;
> +
> +	ret = reset_control_assert(res->rst);
> +	if (ret) {
> +		dev_err(dev, "reset assert failed (%d)\n", ret);
> +		return ret;
> +	}
> +
> +	/*
> +	 * Delay periods before and after reset deassert are working values
> +	 * from downstream Codeaurora kernel
> +	 */
> +	usleep_range(2000, 2500);
> +
> +	ret = reset_control_deassert(res->rst);
> +	if (ret) {
> +		dev_err(dev, "reset deassert failed (%d)\n", ret);
> +		return ret;
> +	}
> +
> +	usleep_range(2000, 2500);
> +
> +	ret = clk_bulk_prepare_enable(ARRAY_SIZE(res->clks), res->clks);
> +	if (ret)
> +		goto err_reset;
> +
> +	return 0;
> +
> +err_reset:
> +	reset_control_assert(res->rst);
> +
> +	return ret;
> +}
> +
> +static int qcom_pcie_post_init_2_9_0(struct qcom_pcie *pcie)
> +{
> +	struct dw_pcie *pci = pcie->pci;
> +	u16 offset = dw_pcie_find_capability(pci, PCI_CAP_ID_EXP);
> +	u32 val;
> +	int i;
> +
> +	writel(SLV_ADDR_SPACE_SZ,
> +		pcie->parf + PCIE20_v3_PARF_SLV_ADDR_SPACE_SIZE);
> +
> +	val = readl(pcie->parf + PCIE20_PARF_PHY_CTRL);
> +	val &= ~BIT(0);
> +	writel(val, pcie->parf + PCIE20_PARF_PHY_CTRL);
> +
> +	writel(0, pcie->parf + PCIE20_PARF_DBI_BASE_ADDR);
> +
> +	writel(DEVICE_TYPE_RC, pcie->parf + PCIE20_PARF_DEVICE_TYPE);
> +	writel(BYPASS | MSTR_AXI_CLK_EN | AHB_CLK_EN,
> +		pcie->parf + PCIE20_PARF_MHI_CLOCK_RESET_CTRL);
> +	writel(GEN3_RELATED_OFF_RXEQ_RGRDLESS_RXTS
> +		| GEN3_RELATED_OFF_GEN3_ZRXDC_NONCOMPL,

I noticed that some of this probably has been copied from from
qcom_pcie_init_2_3_3(), but please move the | operator to the previous
line.

> +		pci->dbi_base + GEN3_RELATED_OFF);
> +
> +	writel(MST_WAKEUP_EN | SLV_WAKEUP_EN | MSTR_ACLK_CGC_DIS
> +		| SLV_ACLK_CGC_DIS | CORE_CLK_CGC_DIS |

Same here.

> +		AUX_PWR_DET | L23_CLK_RMV_DIS | L1_CLK_RMV_DIS,
> +		pcie->parf + PCIE20_PARF_SYS_CTRL);
> +
> +	writel(0, pcie->parf + PCIE20_PARF_Q2A_FLUSH);
> +
> +	dw_pcie_dbi_ro_wr_en(pci);
> +	writel(PCIE_CAP_SLOT_VAL, pci->dbi_base + offset + PCI_EXP_SLTCAP);
> +
> +	val = readl(pci->dbi_base + offset + PCI_EXP_LNKCAP);
> +	val &= ~PCI_EXP_LNKCAP_ASPMS;
> +	writel(val, pci->dbi_base + offset + PCI_EXP_LNKCAP);
> +
> +	writel(PCI_EXP_DEVCTL2_COMP_TMOUT_DIS, pci->dbi_base + offset +
> +			PCI_EXP_DEVCTL2);
> +
> +	for (i = 0; i < 256; i++)
> +		writel(0x0, pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N
> +				+ (4 * i));

And here for +, but you should probably just remove the line break (you
can go up to 100 chars if it makes the code more readable).

Please drop the 0x prefix too.

> +
> +	return 0;
> +}

Johan



[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux