[PATCH v6] PCI: Make sure the bus bridge powered on when scanning bus

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



A bridge in a non-D0 power state does not forward config accesses to
its secondary side (PCIe r6.0, sec 5.3.1). Make sure the bridge is
in D0 while we enumerate devices below it.

The case can be produced when the bridge is runtime-suspended (either
in D3hot or D3cold) like below:

$ echo 1 > /sys/bus/pci/devices/0000:80:00.0/0000:81:00.1/remove
$ echo 1 > /sys/bus/pci/devices/0000:80:00.0/pci_bus/0000:81/rescan

0000:80:00.0 is a Root Port and it is runtime-suspended, so the
configuration space of 0000:81:00.1 is unreachable in rescan
and the device cannot be enumerated.

Power up the bridge when scanning the child bus and allow it to
suspend again by adding pm_runtime_get_sync()/pm_runtime_put()
in pci_scan_child_bus_extend().

Cc: Rafael J. Wysocki <rafael@xxxxxxxxxx>
Cc: Mika Westerberg <mika.westerberg@xxxxxxxxxxxxxxx>
Cc: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
Signed-off-by: Yicong Yang <yangyicong@xxxxxxxxxxxxx>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@xxxxxxxxx>
---
Change since v5:
- Tweak the commit message suggested by Bjorn
Link: https://lore.kernel.org/linux-pci/20220525141930.GA290827@bhelgaas/

Change since v4:
- rephrase the commit suggested by Rafael
Link: https://lore.kernel.org/lkml/20220422080404.27724-1-yangyicong@xxxxxxxxxxxxx/

Change since v3:
- retain the pm_runtime_*() calls in pci_scan_bridge_extend() as Rafael points
  out that it's necessary when the brigde is in D3cold
Link: https://lore.kernel.org/linux-pci/20220414123736.34150-1-yangyicong@xxxxxxxxxxxxx/

Change since v2:
- just rebase it on v5.18-rc2
Link: https://lore.kernel.org/linux-pci/1601029386-4928-1-git-send-email-yangyicong@xxxxxxxxxxxxx/

Change since v1:
- use an intermediate variable *bridge as suggested
- remove the pm_runtime_*() calls in pci_scan_bridge_extend()
Link: https://lore.kernel.org/linux-pci/1596022223-4765-1-git-send-email-yangyicong@xxxxxxxxxxxxx/

 drivers/pci/probe.c | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index 17a969942d37..b108e72b6586 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -2859,11 +2859,20 @@ static unsigned int pci_scan_child_bus_extend(struct pci_bus *bus,
 	unsigned int used_buses, normal_bridges = 0, hotplug_bridges = 0;
 	unsigned int start = bus->busn_res.start;
 	unsigned int devfn, fn, cmax, max = start;
+	struct pci_dev *bridge = bus->self;
 	struct pci_dev *dev;
 	int nr_devs;
 
 	dev_dbg(&bus->dev, "scanning bus\n");
 
+	/*
+	 * Make sure the bus bridge is powered on, otherwise we may not be
+	 * able to scan the devices as we may fail to access the configuration
+	 * space of subordinates.
+	 */
+	if (bridge)
+		pm_runtime_get_sync(&bridge->dev);
+
 	/* Go find them, Rover! */
 	for (devfn = 0; devfn < 256; devfn += 8) {
 		nr_devs = pci_scan_slot(bus, devfn);
@@ -2976,6 +2985,9 @@ static unsigned int pci_scan_child_bus_extend(struct pci_bus *bus,
 		}
 	}
 
+	if (bridge)
+		pm_runtime_put(&bridge->dev);
+
 	/*
 	 * We've scanned the bus and so we know all about what's on
 	 * the other side of any bridges that may be on this bus plus
-- 
2.24.0




[Index of Archives]     [DMA Engine]     [Linux Coverity]     [Linux USB]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [Greybus]

  Powered by Linux