00:00.0 Root Port to [bus 01-??] # soldered on to Unmatched 01:00.0 ASM2824 Upstream Port to [bus 02-09] # soldered on 02:03.0 ASM2824 Downstream Port to [bus 05-09] # soldered on, to slot 05:00.0 PI7C9X2G304 Upstream Port to [bus 06-09] # on Delock riser card 06:??.? PI7C9X2G304 Downstream Port to [bus ??] # slot 0 on Delock card 06:??.? PI7C9X2G304 Downstream Port to [bus ??] # slot 1 on Delock card Do we have other reports of this bridge being broken? Or could this be some kind of signal integrity problem on Unmatched or the slot? The ASM2824 has been around for a while and seems to be used in other systems, e.g., https://linux-hardware.org/?id=pci:1b21-2824, so if it's an ASM2824 issue, we should see it elsewhere, too. > However the link continues oscillating between the two speeds, at the > rate of 34-35 times per second, with link training reported repeatedly > active ~84% of the time, e.g.: > > 02:03.0 PCI bridge [0604]: ASMedia Technology Inc. ASM2824 PCIe Gen3 Packet Switch [1b21:2824] (rev 01) (prog-if 00 [Normal decode]) > [...] > Bus: primary=02, secondary=05, subordinate=05, sec-latency=0 > [...] > Capabilities: [80] Express (v2) Downstream Port (Slot+), MSI 00 > [...] > LnkSta: Speed 5GT/s (downgraded), Width x1 (ok) > TrErr- Train+ SlotClk+ DLActive- BWMgmt+ ABWMgmt- > [...] > LnkCtl2: Target Link Speed: 8GT/s, EnterCompliance- SpeedDis+, Selectable De-emphasis: -3.5dB > Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > [...] > > Forcibly limiting the target link speed to 2.5GT/s with the upstream > ASM2824 device makes the two switches communicate correctly however: > > 02:03.0 PCI bridge [0604]: ASMedia Technology Inc. ASM2824 PCIe Gen3 Packet Switch [1b21:2824] (rev 01) (prog-if 00 [Normal decode]) > [...] > Bus: primary=02, secondary=05, subordinate=09, sec-latency=0 > [...] > Capabilities: [80] Express (v2) Downstream Port (Slot+), MSI 00 > [...] > LnkSta: Speed 2.5GT/s (downgraded), Width x1 (ok) > TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- > [...] > LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis+, Selectable De-emphasis: -3.5dB > Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > [...] > > and then: > > 05:00.0 PCI bridge [0604]: Pericom Semiconductor PI7C9X2G304 EL/SL PCIe2 3-Port/4-Lane Packet Switch [12d8:2304] (rev 05) (prog-if 00 [Normal decode]) > [...] > Bus: primary=05, secondary=06, subordinate=09, sec-latency=0 > [...] > Capabilities: [c0] Express (v2) Upstream Port, MSI 00 > [...] > LnkSta: Speed 2.5GT/s (downgraded), Width x1 (downgraded) > TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- > [...] > LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis- > Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS- > Compliance De-emphasis: -6dB > [...] I think the above is supposed to show 02:03.0 operating at 5GT/s or 2.5GT/s, and 05:00.0 operating at 2.5GT/s. But there's a lot of noise that makes it hard to pick out what's important. > Removing the speed restriction afterwards makes the two devices switch > to 5.0GT/s then. > > Make use of these observations then and detect the inability to train > the link, by checking for the Data Link Layer Link Active status bit > implemented by the ASM2824 being off while the Link Bandwidth Management > Status indicating that hardware has changed the link speed or width in > an attempt to correct unreliable link operation. > > Restrict the speed to 2.5GT/s then with the Target Link Speed field, > request a retrain and wait 200ms for the data link to go up. If this > turns out successful, then lift the restriction, letting the devices > negotiate a higher speed. Also check for a 2.5GT/s speed restriction > the firmware may have already arranged and lift it too with ports that > already report their data link being up. > > Signed-off-by: Maciej W. Rozycki <macro@xxxxxxxxxxx> > --- > Hi, > > Patch regenerated and re-verified against 5.17-rc2. On this occasion I > decided to remove BUG_ON after all for a supposedly impossible condition > of a missing PCI Express capability for this PCIe switch and instead use > WARN_ON and an early return. It should be safer this way. > > NB the corresponding U-boot change has since gone in with commit > a398a51ccc68 ("pci: Work around PCIe link training failures"). See Please include a URL for this commit. Without knowing where to use it, the SHA1 by itself isn't much use. > <https://lore.kernel.org/lkml/alpine.DEB.2.21.2201022100430.56863@xxxxxxxxxxxxxxxxx/> > for previous background information. > > Questions, comments, concerns? Otherwise please apply. > > Maciej > > Changes from v2: > > - Regenerate for 5.17-rc2 for a merge conflict. > > - Replace BUG_ON for a missing PCI Express capability with WARN_ON and an > early return. > > Changes from v1: > > - Regenerate for a merge conflict. > --- > drivers/pci/quirks.c | 98 ++++++++++++++++++++++++++++++++++++++++++++++++ > include/linux/pci_ids.h | 1 > 2 files changed, 99 insertions(+) > > linux-pcie-asm2824-manual-retrain.diff > Index: linux-macro/drivers/pci/quirks.c > =================================================================== > --- linux-macro.orig/drivers/pci/quirks.c > +++ linux-macro/drivers/pci/quirks.c > @@ -12,6 +12,7 @@ > * file, where their drivers can use them. > */ > > +#include <linux/bug.h> > #include <linux/types.h> > #include <linux/kernel.h> > #include <linux/export.h> > @@ -5879,3 +5880,100 @@ DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_IN > DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1536, rom_bar_overlap_defect); > DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1537, rom_bar_overlap_defect); > DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_INTEL, 0x1538, rom_bar_overlap_defect); > + > +/* > + * Retrain the link of a downstream PCIe port by hand if necessary. > + * > + * This is needed at least where a downstream port of the ASMedia ASM2824 > + * Gen 3 switch is wired to the upstream port of the Pericom PI7C9X2G304 > + * Gen 2 switch, and observed with the Delock Riser Card PCI Express x1 > > + * 2 x PCIe x1 device, P/N 41433, plugged into the SiFive HiFive Unmatched > + * board. > + * > + * In such a configuration the switches are supposed to negotiate the link > + * speed of preferably 5.0GT/s, falling back to 2.5GT/s. However the link > + * continues switching between the two speeds indefinitely and the data > + * link layer never reaches the active state, with link training reported > + * repeatedly active ~84% of the time. Forcing the target link speed to > + * 2.5GT/s with the upstream ASM2824 device makes the two switches talk to > + * each other correctly however. And more interestingly retraining with a > + * higher target link speed afterwards lets the two successfully negotiate > + * 5.0GT/s. > + * > + * With the ASM2824 we can rely on the otherwise optional Data Link Layer > + * Link Active status bit and in the failed link training scenario it will > + * be off along with the Link Bandwidth Management Status indicating that > + * hardware has changed the link speed or width in an attempt to correct > + * unreliable link operation. For a port that has been left unconnected > + * both bits will be clear. So use this information to detect the problem > + * rather than polling the Link Training bit and watching out for flips or > + * at least the active status. > + * > + * Restrict the speed to 2.5GT/s then with the Target Link Speed field, > + * request a retrain and wait 200ms for the data link to go up. If this > + * turns out successful, then lift the restriction, letting the devices > + * negotiate a higher speed. Also check for a 2.5GT/s speed restriction > + * the firmware may have already arranged and lift it too with ports that > + * already report their data link being up. > + */ > +static void pcie_downstream_link_retrain(struct pci_dev *dev) > +{ > + u16 lnksta, lnkctl2; > + u8 pos; > + > + pos = pci_find_capability(dev, PCI_CAP_ID_EXP); > + WARN_ON(!pos); > + if (!pos) > + return; > + > + pci_read_config_word(dev, pos + PCI_EXP_LNKCTL2, &lnkctl2); > + pci_read_config_word(dev, pos + PCI_EXP_LNKSTA, &lnksta); > + if ((lnksta & (PCI_EXP_LNKSTA_LBMS | PCI_EXP_LNKSTA_DLLLA)) == > + PCI_EXP_LNKSTA_LBMS) { > + unsigned long timeout; > + u16 lnkctl; > + > + pci_info(dev, "broken device, retraining non-functional downstream link at 2.5GT/s...\n"); > + > + pci_read_config_word(dev, pos + PCI_EXP_LNKCTL, &lnkctl); > + lnkctl |= PCI_EXP_LNKCTL_RL; > + lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS; > + lnkctl2 |= PCI_EXP_LNKCTL2_TLS_2_5GT; > + pci_write_config_word(dev, pos + PCI_EXP_LNKCTL2, lnkctl2); > + pci_write_config_word(dev, pos + PCI_EXP_LNKCTL, lnkctl); > + > + timeout = jiffies + msecs_to_jiffies(200); > + do { > + pci_read_config_word(dev, pos + PCI_EXP_LNKSTA, > + &lnksta); > + if (lnksta & PCI_EXP_LNKSTA_DLLLA) > + break; > + usleep_range(10000, 20000); > + } while (time_before(jiffies, timeout)); > + > + pci_info(dev, "retraining %s!\n", > + lnksta & PCI_EXP_LNKSTA_DLLLA ? > + "succeeded" : "failed"); > + } Perhaps a place to use pcie_retrain_link() (would require a little rework to make it usable outside aspm.c). > + > + if ((lnksta & PCI_EXP_LNKSTA_DLLLA) && > + (lnkctl2 & PCI_EXP_LNKCTL2_TLS) == PCI_EXP_LNKCTL2_TLS_2_5GT) { > + u32 lnkcap; > + u16 lnkctl; > + > + pci_info(dev, "removing 2.5GT/s downstream link speed restriction\n"); > + pci_read_config_word(dev, pos + PCI_EXP_LNKCTL, &lnkctl); > + pci_read_config_dword(dev, pos + PCI_EXP_LNKCAP, &lnkcap); > + lnkctl |= PCI_EXP_LNKCTL_RL; > + lnkctl2 &= ~PCI_EXP_LNKCTL2_TLS; > + lnkctl2 |= lnkcap & PCI_EXP_LNKCAP_SLS; > + pci_write_config_word(dev, pos + PCI_EXP_LNKCTL2, lnkctl2); > + pci_write_config_word(dev, pos + PCI_EXP_LNKCTL, lnkctl); > + } > +} > +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ASMEDIA, > + PCI_DEVICE_ID_ASMEDIA_ASM2824, > + pcie_downstream_link_retrain); > +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_ASMEDIA, > + PCI_DEVICE_ID_ASMEDIA_ASM2824, > + pcie_downstream_link_retrain); > Index: linux-macro/include/linux/pci_ids.h > =================================================================== > --- linux-macro.orig/include/linux/pci_ids.h > +++ linux-macro/include/linux/pci_ids.h > @@ -2545,6 +2545,7 @@ > #define PCI_SUBDEVICE_ID_QEMU 0x1100 > > #define PCI_VENDOR_ID_ASMEDIA 0x1b21 > +#define PCI_DEVICE_ID_ASMEDIA_ASM2824 0x2824 We only add to pci_ids.h when the ID is used in more than one place.
