On Tue, Nov 23, 2021 at 06:06:34PM +0000, Marc Zyngier wrote:
> While the Apple PCIe driver works correctly when directly booted
> from the firmware, it fails to initialise when the kernel is booted
> from a bootloader using PCIe such as u-boot.
>
> That's beacuse we're missing a proper reset of the port (we only
> clear the reset, but never assert it).
>
> The PCIe spec requirements are two-fold:
>
> - #PERST must be asserted before setting up the clocks, and
> stay asserted for at least 100us (Tperst-clk).
>
> - Once #PERST is deasserted, the OS must wait for at least 100ms
> "from the end of a Conventional Reset" before we can start talking
> to the devices
Unless somebody objects, I'll s/#PERST/PERST#/ to match the spec
usage, both here and in the comments below.
I also notice gpiod_get_from_of_node(..., "#PERST") earlier in
apple_pcie_setup_port(). If it wouldn't break anything, I'd like to
change that, too.
> Implementing this results in a booting system.
>
> Fixes: 1e33888fbe44 ("PCI: apple: Add initial hardware bring-up")
> Acked-by: Pali Rohár <pali@xxxxxxxxxx>
> Signed-off-by: Marc Zyngier <maz@xxxxxxxxxx>
> Cc: Alyssa Rosenzweig <alyssa@xxxxxxxxxxxxx>
> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@xxxxxxx>
> Cc: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
> ---
> drivers/pci/controller/pcie-apple.c | 10 ++++++++++
> 1 file changed, 10 insertions(+)
>
> diff --git a/drivers/pci/controller/pcie-apple.c b/drivers/pci/controller/pcie-apple.c
> index 1bf4d75b61be..957960a733c4 100644
> --- a/drivers/pci/controller/pcie-apple.c
> +++ b/drivers/pci/controller/pcie-apple.c
> @@ -539,13 +539,23 @@ static int apple_pcie_setup_port(struct apple_pcie *pcie,
>
> rmw_set(PORT_APPCLK_EN, port->base + PORT_APPCLK);
>
> + /* Engage #PERST before setting up the clock */
> + gpiod_set_value(reset, 0);
> +
> ret = apple_pcie_setup_refclk(pcie, port);
> if (ret < 0)
> return ret;
>
> + /* The minimal Tperst-clk value is 100us (PCIe CMS r2.0, 2.6.2) */
> + usleep_range(100, 200);
Spec says "min 100us from REFCLK stable before PERST# inactive". So I
guess when apple_pcie_setup_refclk() returns, we know REFCLK is
already stable?
> + /* Deassert #PERST */
> rmw_set(PORT_PERST_OFF, port->base + PORT_PERST);
> gpiod_set_value(reset, 1);
>
> + /* Wait for 100ms after #PERST deassertion (PCIe r2.0, 6.6.1) */
> + msleep(100);
Does this port support speeds greater than 5 GT/s? If so, 6.6.1 says
we need "100ms after Link training completes," not just after
deasserting PERST#.
I'll update this citation to "PCIe r5.0, 6.6.1" to reference the
current spec.
> ret = readl_relaxed_poll_timeout(port->base + PORT_STATUS, stat,
> stat & PORT_STATUS_READY, 100, 250000);
> if (ret < 0) {
> --
> 2.30.2
>
