Hi Enric, On Sat, Oct 19, 2013 at 9:54 PM, Enric Balletbo i Serra <eballetbo@xxxxxxxxx> wrote: > The LBEE1USJYC is a WiFi/BT combo module used on OMAP3-based IGEP boards. In > both cases, IGEPv2 Rev. C and IGEP COM MODULE, the module is connected using > the same MMC interface and uses the same GPIOs. > > Signed-off-by: Enric Balletbo i Serra <eballetbo@xxxxxxxxx> > --- > arch/arm/boot/dts/omap3-igep.dtsi | 45 ++++++++++++++++++++++++++++++++++++++- > 1 file changed, 44 insertions(+), 1 deletion(-) > > diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi > index d4fecce..882e318 100644 > --- a/arch/arm/boot/dts/omap3-igep.dtsi > +++ b/arch/arm/boot/dts/omap3-igep.dtsi > @@ -24,6 +24,25 @@ > ti,mcbsp = <&mcbsp2>; > ti,codec = <&twl_audio>; > }; > + > + vdd33: regulator-vdd33 { > + compatible = "regulator-fixed"; > + regulator-name = "vdd33"; > + regulator-always-on; > + }; > + > + lbee1usjyc_vmmc: lbee1usjyc_vmmc { > + pinctrl-names = "default"; > + pinctrl-0 = <&lbee1usjyc_pins>; > + compatible = "regulator-fixed"; > + regulator-name = "regulator-lbee1usjyc"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&gpio5 10 0>; /* gpio_138 WIFI_PDN */ Is better if you use GPIO_ACTIVE_HIGH instead of 0 here. > + startup-delay-us = <10000>; > + enable-active-high; > + vin-supply = <&vdd33>; > + }; > }; > > &omap3_pmx_core { > @@ -48,6 +67,15 @@ > >; > }; > > + /* WiFi/BT combo */ > + lbee1usjyc_pins: pinmux_lbee1usjyc_pins { > + pinctrl-single,pins = < > + 0x136 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat5.gpio_137 */ > + 0x138 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat6.gpio_138 */ > + 0x13a (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 */ > + >; > + }; > + Is this enough to correctly reset the chip or do you also have a patch to do the init sequence on pdata-quirks.c? > mcbsp2_pins: pinmux_mcbsp2_pins { > pinctrl-single,pins = < > 0x10c (PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx.mcbsp2_fsx */ > @@ -68,6 +96,17 @@ > >; > }; > > + mmc2_pins: pinmux_mmc2_pins { > + pinctrl-single,pins = < > + 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ > + 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ > + 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ > + 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ > + 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ > + 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ > + >; > + }; > + > smsc911x_pins: pinmux_smsc911x_pins { > pinctrl-single,pins = < > 0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */ > @@ -114,7 +153,11 @@ > }; > > &mmc2 { > - status = "disabled"; > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc2_pins>; > + vmmc-supply = <&lbee1usjyc_vmmc>; > + bus-width = <4>; > + non-removable; > }; > > &mmc3 { > -- > 1.8.1.2 > Best regards, Javier -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html