The LBEE1USJYC is a WiFi/BT combo module used on OMAP3-based IGEP boards. In
both cases, IGEPv2 Rev. C and IGEP COM MODULE, the module is connected using
the same MMC interface and uses the same GPIOs.
Signed-off-by: Enric Balletbo i Serra <eballetbo@xxxxxxxxx>
---
arch/arm/boot/dts/omap3-igep.dtsi | 45 ++++++++++++++++++++++++++++++++++++++-
1 file changed, 44 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index d4fecce..882e318 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/omap3-igep.dtsi
@@ -24,6 +24,25 @@
ti,mcbsp = <&mcbsp2>;
ti,codec = <&twl_audio>;
};
+
+ vdd33: regulator-vdd33 {
+ compatible = "regulator-fixed";
+ regulator-name = "vdd33";
+ regulator-always-on;
+ };
+
+ lbee1usjyc_vmmc: lbee1usjyc_vmmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lbee1usjyc_pins>;
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-lbee1usjyc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio5 10 0>; /* gpio_138 WIFI_PDN */
+ startup-delay-us = <10000>;
+ enable-active-high;
+ vin-supply = <&vdd33>;
+ };
};
&omap3_pmx_core {
@@ -48,6 +67,15 @@
>;
};
+ /* WiFi/BT combo */
+ lbee1usjyc_pins: pinmux_lbee1usjyc_pins {
+ pinctrl-single,pins = <
+ 0x136 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat5.gpio_137 */
+ 0x138 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat6.gpio_138 */
+ 0x13a (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 */
+ >;
+ };
+
mcbsp2_pins: pinmux_mcbsp2_pins {
pinctrl-single,pins = <
0x10c (PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx.mcbsp2_fsx */
@@ -68,6 +96,17 @@
>;
};
+ mmc2_pins: pinmux_mmc2_pins {
+ pinctrl-single,pins = <
+ 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
+ 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
+ 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
+ 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
+ 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
+ 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
+ >;
+ };
+
smsc911x_pins: pinmux_smsc911x_pins {
pinctrl-single,pins = <
0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
@@ -114,7 +153,11 @@
};
&mmc2 {
- status = "disabled";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ vmmc-supply = <&lbee1usjyc_vmmc>;
+ bus-width = <4>;
+ non-removable;
};
&mmc3 {
--
1.8.1.2
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
