Re: [PATCH 1/2] ARM: dts: AM33XX: Add support for IGEP COM AQUILA

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Enric,

On 06/19/2013 03:27 AM, Enric Balletbo i Serra wrote:
The IGEP COM AQUILA is industrial processors SODIMM module with
following highlights:

    o AM3352/AM3354/AM3358/AM3359 Texas Instruments processor
    o Cortex-A8 ARM CPU
    o 3.3 volts Inputs / Outputs use industrial
    o 256 MB DDR3 SDRAM / 128 Megabytes FLASH
    o MicroSD card reader on-board
    o Ethernet controller on-board
    o JTAG debug connector available
    o Designed for industrial range purposes

Signed-off-by: Enric Balletbo i Serra <eballetbo@xxxxxxxxxxx>
---
  arch/arm/boot/dts/am335x-igep0033.dtsi | 269 +++++++++++++++++++++++++++++++++
  1 file changed, 269 insertions(+)
  create mode 100644 arch/arm/boot/dts/am335x-igep0033.dtsi

diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi
new file mode 100644
index 0000000..1d70141
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-igep0033.dtsi
@@ -0,0 +1,269 @@
+/*
+ * Copyright (C) 2013 ISEE 2007 SL - http://www.isee.biz/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vdd1_reg>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	am33xx_pinmux: pinmux@44e10800 {

That node should be inside the ocp one since the control module is a regular IP connected to the OCP interconnect.


+		pinctrl-names = "default";
+
+		i2c0_pins: pinmux_i2c0_pins {
+			pinctrl-single,pins = <
+				0x188 (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+				0x18c (PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+			>;
+		};
+
+		nandflash_pins: pinmux_nandflash_pins {
+			pinctrl-single,pins = <
+				0x0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+				0x4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+				0x8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+				0xc (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+				0x10 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+				0x14 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+				0x18 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+				0x1c (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+				0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+				0x74 (PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpio0_30 */
+				0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0  */
+				0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+				0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+				0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+				0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+			>;
+		};
+
+		uart0_pins: pinmux_uart0_pins {
+			pinctrl-single,pins = <
+				0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+				0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+			>;
+		};
+
+		user_leds: pinmux_user_leds_pins {
+			pinctrl-single,pins = <
+				0x5c (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a7.gpio1_23 */
+			>;
+		};
+
+	};
+
+	ocp {
+		uart0: serial@44e09000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_pins>;
+			status = "okay";
+		};
+
+		i2c0: i2c@44e0b000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+
+			status = "okay";
+			clock-frequency = <400000>;
+
+			tps: tps@2d {
+				reg = <0x2d>;
+			};
+		};
+
+		elm: elm@48080000 {
+			status = "okay";
+		};
+
+		gpmc: gpmc@50000000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&nandflash_pins>;
+
+			status = "okay";
+			ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+
+			nand@0,0 {
+				reg = <0 0 0>; /* CS0, offset 0 */
+				nand-bus-width = <8>;
+				ti,nand-ecc-opt = "bch8";
+				gpmc,device-nand = "true";
+				gpmc,device-width = <1>;
+				gpmc,sync-clk-ps = <0>;
+				gpmc,cs-on-ns = <0>;
+				gpmc,cs-rd-off-ns = <44>;
+				gpmc,cs-wr-off-ns = <44>;
+				gpmc,adv-on-ns = <6>;
+				gpmc,adv-rd-off-ns = <34>;
+				gpmc,adv-wr-off-ns = <44>;
+				gpmc,we-on-ns = <0>;
+				gpmc,we-off-ns = <40>;
+				gpmc,oe-on-ns = <0>;
+				gpmc,oe-off-ns = <54>;
+				gpmc,access-ns = <64>;
+				gpmc,rd-cycle-ns = <82>;
+				gpmc,wr-cycle-ns = <82>;
+				gpmc,wait-on-read = "true";
+				gpmc,wait-on-write = "true";
+				gpmc,bus-turnaround-ns = <0>;
+				gpmc,cycle2cycle-delay-ns = <0>;
+				gpmc,clk-activation-ns = <0>;
+				gpmc,wait-monitoring-ns = <0>;
+				gpmc,wr-access-ns = <40>;
+				gpmc,wr-data-mux-bus-ns = <0>;
+
+				#address-cells = <1>;
+				#size-cells = <1>;
+				elm_id = <&elm>;
+
+				/* MTD partition table */
+				partition@0 {
+					label = "SPL";
+					reg = <0x00000000 0x000080000>;
+				};
+
+				partition@1 {
+					label = "U-boot";
+					reg = <0x00080000 0x001e0000>;
+				};
+
+				partition@2 {
+					label = "U-Boot Env";
+					reg = <0x00260000 0x00020000>;
+				};
+
+				partition@3 {
+					label = "Kernel";
+					reg = <0x00280000 0x00500000>;
+				};
+
+				partition@4 {
+					label = "File System";
+					reg = <0x00780000 0x0F880000>;
+				};
+			};
+		};
+	};
+
+	leds {
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_leds>;
+
+		compatible = "gpio-leds";
+
+		led@0 {
+			label = "com:green:user";
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+};
+
+#include "tps65910.dtsi"
+
+&tps {
+	vcc1-supply = <&vbat>;
+	vcc2-supply = <&vbat>;
+	vcc3-supply = <&vbat>;
+	vcc4-supply = <&vbat>;
+	vcc5-supply = <&vbat>;
+	vcc6-supply = <&vbat>;
+	vcc7-supply = <&vbat>;
+	vccio-supply = <&vbat>;
+
+	regulators {
+		vrtc_reg: regulator@0 {
+			regulator-always-on;
+		};
+
+		vio_reg: regulator@1 {
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1312500>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1150000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd3_reg: regulator@4 {
+			regulator-always-on;
+		};
+
+		vdig1_reg: regulator@5 {
+			regulator-always-on;
+		};
+
+		vdig2_reg: regulator@6 {
+			regulator-always-on;
+		};
+
+		vpll_reg: regulator@7 {
+			regulator-always-on;
+		};
+
+		vdac_reg: regulator@8 {
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			regulator-always-on;
+		};
+
+		vaux33_reg: regulator@11 {
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			regulator-always-on;
+		};
+	};
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <1>;
+};
+



Otherwise, it looks good.

Thanks,
Benoit
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux