Hello Dan,
On 05/31/2013 05:19 PM, Dan Murphy wrote:
The GPIO for LED D1 on the omap4-panda a1-a3 rev and the omap4-panda-es
are different.
A1-A3 = gpio_wk7
ES = gpio_110
There is no change to LED D2
Abstract away the pinmux and the LED definitions for the two boards into
the respective DTS files.
Signed-off-by: Dan Murphy <dmurphy@xxxxxx>
---
v9 - Removed comments for mux config - https://patchwork.kernel.org/patch/2644391/
v8 - Rebase to latest and use pinctrl macros - https://patchwork.kernel.org/patch/2629351/
v7 - Update headline to add spaces - https://patchwork.kernel.org/patch/2583661/
v6 - Review comments updated - https://patchwork.kernel.org/patch/2582771/
v5 - Provide pincrtl phandle to the gpio-led driver - https://patchwork.kernel.org/patch/2573981/
arch/arm/boot/dts/omap4-panda-common.dtsi | 16 +++++++++++++++-
arch/arm/boot/dts/omap4-panda-es.dts | 28 ++++++++++++++++++++++++++++
2 files changed, 43 insertions(+), 1 deletions(-)
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index d5d144a..800fa4e 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -16,8 +16,13 @@
reg = <0x80000000 0x40000000>; /* 1 GB */
};
- leds {
+ leds: leds {
compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &led_wkgpio_pins
+ >;
+
heartbeat {
label = "pandaboard::status1";
gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
@@ -157,6 +162,15 @@
};
};
+&omap4_pmx_wkup {
+ led_wkgpio_pins: pinmux_leds_wkpins {
+ pinctrl-single,pins = <
+ 0x1a (PIN_OUTPUT | MUX_MODE3) /* gpio_wk7 */
+ 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
+ >;
+ };
+};
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts
index 5cfdf19..0a7812f 100644
--- a/arch/arm/boot/dts/omap4-panda-es.dts
+++ b/arch/arm/boot/dts/omap4-panda-es.dts
@@ -34,3 +34,31 @@
0x5e (PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */
>;
};
+
+&omap4_pmx_core {
+ led_gpio_pins: gpio_led_pmx {
+ pinctrl-single,pins = <
+ 0xb6 (PIN_OUTPUT | MUX_MODE3) /* gpio_110 */
+ >;
+ };
+};
+
+&led_wkgpio_pins {
+ pinctrl-single,pins = <
+ 0x1c (PIN_OUTPUT | MUX_MODE3) /* gpio_wk8 */
+ >;
+};
+
+&leds {
+ pinctrl-0 = <
+ &led_gpio_pins
+ &led_wkgpio_pins
+ >;
+
+ heartbeat {
+ gpios = <&gpio4 14 0>;
And here you could use the GPIO defines:
gpios = <&gpio4 14 GPIO_ACTIVE_HIGH>;
+ };
+ mmc {
+ gpios = <&gpio1 8 0>;
Same here.
+ };
+};
Regards,
Florian
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
