Add 2 platform devices for 'nop-usb-xceiv'. These will be used as a
PHY for HS USB Port 1 and 2, so provide binding information for them.
Model RESET for HS USB Port 1 as GPIO fixed regulator and link it
to the 'nop-usb-xceiv' PHY on port 1.
Signed-off-by: Roger Quadros <rogerq@xxxxxx>
Acked-by: Felipe Balbi <balbi@xxxxxx>
---
arch/arm/mach-omap2/board-am3517evm.c | 66 ++++++++++++++++++++++++++++++---
1 files changed, 60 insertions(+), 6 deletions(-)
diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c
index 9fb8590..36c00fb 100644
--- a/arch/arm/mach-omap2/board-am3517evm.c
+++ b/arch/arm/mach-omap2/board-am3517evm.c
@@ -25,6 +25,9 @@
#include <linux/can/platform/ti_hecc.h>
#include <linux/davinci_emac.h>
#include <linux/mmc/host.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/usb/phy.h>
#include <linux/usb/musb.h>
#include <linux/platform_data/gpio-omap.h>
@@ -274,6 +277,50 @@ static __init void am3517_evm_mcbsp1_init(void)
omap_ctrl_writel(devconf0, OMAP2_CONTROL_DEVCONF0);
}
+/* PHY device on HS USB Port 1 i.e. nop_usb_xceiv.1 */
+static struct platform_device hsusb1_phy_device = {
+ .name = "nop_usb_xceiv",
+ .id = 1,
+};
+
+/* Regulator for HS USB Port 1 PHY reset */
+static struct regulator_consumer_supply hsusb1_reset_supplies[] = {
+ /* Link PHY device to reset supply so it gets used in the PHY driver */
+ REGULATOR_SUPPLY("reset", "nop_usb_xceiv.1"),
+};
+
+static struct regulator_init_data hsusb1_reset_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .consumer_supplies = hsusb1_reset_supplies,
+ .num_consumer_supplies = ARRAY_SIZE(hsusb1_reset_supplies),
+};
+
+static struct fixed_voltage_config hsusb1_reset_config = {
+ .supply_name = "hsusb1_reset",
+ .microvolts = 3300000,
+ .gpio = 57,
+ .startup_delay = 70000, /* 70msec */
+ .enable_high = 1,
+ .enabled_at_boot = 0, /* keep in RESET */
+ .init_data = &hsusb1_reset_data,
+};
+
+static struct platform_device hsusb1_reset_device = {
+ .name = "reg-fixed-voltage",
+ .id = PLATFORM_DEVID_AUTO,
+ .dev = {
+ .platform_data = &hsusb1_reset_config,
+ },
+};
+
+/* PHY device on HS USB Port 2 i.e. nop_usb_xceiv.2 */
+static struct platform_device hsusb2_phy_device = {
+ .name = "nop_usb_xceiv",
+ .id = 2,
+};
+
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
#if defined(CONFIG_PANEL_SHARP_LQ043T1DG01) || \
@@ -282,12 +329,6 @@ static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
#else
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
#endif
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
-
- .phy_reset = true,
- .reset_gpio_port[0] = 57,
- .reset_gpio_port[1] = -EINVAL,
- .reset_gpio_port[2] = -EINVAL
};
#ifdef CONFIG_OMAP_MUX
@@ -349,6 +390,11 @@ static struct omap2_hsmmc_info mmc[] = {
{} /* Terminator */
};
+static struct platform_device *am3517evm_devices[] __initdata = {
+ &hsusb1_phy_device,
+ &hsusb1_reset_device,
+ &hsusb2_phy_device,
+};
static void __init am3517_evm_init(void)
{
@@ -361,6 +407,14 @@ static void __init am3517_evm_init(void)
/* Configure GPIO for EHCI port */
omap_mux_init_gpio(57, OMAP_PIN_OUTPUT);
+
+ platform_add_devices(am3517evm_devices, ARRAY_SIZE(am3517evm_devices));
+
+ /* PHY on HSUSB Port 1 i.e. index 0 */
+ usb_bind_phy("ehci-omap.0", 0, "nop_usb_xceiv.1");
+ /* PHY on HSUSB Port 2 i.e. index 1 */
+ usb_bind_phy("ehci-omap.0", 1, "nop_usb_xceiv.2");
+
usbhs_init(&usbhs_bdata);
am3517_evm_hecc_init(&am3517_evm_hecc_pdata);
/* DSS */
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
