Add 2 platform devices for 'nop-usb-xceiv'. These will be used
as PHYs for HS USB ports 1 and 2 so provide binding information
for them.
Model RESET for HS USB Ports 1 and 2 as GPIO fixed regulators and
link them to the 2 PHYs we just created.
Signed-off-by: Roger Quadros <rogerq@xxxxxx>
Acked-by: Felipe Balbi <balbi@xxxxxx>
---
arch/arm/mach-omap2/board-cm-t3517.c | 97 ++++++++++++++++++++++++++++++++--
1 files changed, 92 insertions(+), 5 deletions(-)
diff --git a/arch/arm/mach-omap2/board-cm-t3517.c b/arch/arm/mach-omap2/board-cm-t3517.c
index a66da80..de470c8 100644
--- a/arch/arm/mach-omap2/board-cm-t3517.c
+++ b/arch/arm/mach-omap2/board-cm-t3517.c
@@ -34,6 +34,9 @@
#include <linux/mtd/partitions.h>
#include <linux/mmc/host.h>
#include <linux/can/platform/ti_hecc.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
+#include <linux/usb/phy.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -188,15 +191,92 @@ static inline void cm_t3517_init_rtc(void) {}
#define HSUSB2_RESET_GPIO (147)
#define USB_HUB_RESET_GPIO (152)
+/* PHY device on HS USB Port 1 i.e. nop_usb_xceiv.1 */
+static struct platform_device hsusb1_phy_device = {
+ .name = "nop_usb_xceiv",
+ .id = 1,
+};
+
+/* Regulator for HS USB Port 1 PHY reset */
+static struct regulator_consumer_supply hsusb1_reset_supplies[] = {
+ /* Link PHY device to reset supply so it gets used in the PHY driver */
+ REGULATOR_SUPPLY("reset", "nop_usb_xceiv.1"),
+};
+
+static struct regulator_init_data hsusb1_reset_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .consumer_supplies = hsusb1_reset_supplies,
+ .num_consumer_supplies = ARRAY_SIZE(hsusb1_reset_supplies),
+};
+
+static struct fixed_voltage_config hsusb1_reset_config = {
+ .supply_name = "hsusb1_reset",
+ .microvolts = 3300000,
+ .gpio = HSUSB1_RESET_GPIO,
+ .startup_delay = 70000, /* 70msec */
+ .enable_high = 1,
+ .enabled_at_boot = 0, /* keep in RESET */
+ .init_data = &hsusb1_reset_data,
+};
+
+static struct platform_device hsusb1_reset_device = {
+ .name = "reg-fixed-voltage",
+ .id = PLATFORM_DEVID_AUTO,
+ .dev = {
+ .platform_data = &hsusb1_reset_config,
+ },
+};
+
+/* PHY device on HS USB Port 2 i.e. nop_usb_xceiv.2 */
+static struct platform_device hsusb2_phy_device = {
+ .name = "nop_usb_xceiv",
+ .id = 2,
+};
+
+/* Regulator for HS USB Port 2 PHY reset */
+static struct regulator_consumer_supply hsusb2_reset_supplies[] = {
+ /* Link PHY device to reset supply so it gets used in the PHY driver */
+ REGULATOR_SUPPLY("reset", "nop_usb_xceiv.2"),
+};
+
+static struct regulator_init_data hsusb2_reset_data = {
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+ .consumer_supplies = hsusb2_reset_supplies,
+ .num_consumer_supplies = ARRAY_SIZE(hsusb2_reset_supplies),
+};
+
+static struct fixed_voltage_config hsusb2_reset_config = {
+ .supply_name = "hsusb2_reset",
+ .microvolts = 3300000,
+ .gpio = HSUSB2_RESET_GPIO,
+ .startup_delay = 70000, /* 70msec */
+ .enable_high = 1,
+ .enabled_at_boot = 0, /* keep in RESET */
+ .init_data = &hsusb2_reset_data,
+};
+
+static struct platform_device hsusb2_reset_device = {
+ .name = "reg-fixed-voltage",
+ .id = PLATFORM_DEVID_AUTO,
+ .dev = {
+ .platform_data = &hsusb2_reset_config,
+ },
+};
+
static struct usbhs_omap_platform_data cm_t3517_ehci_pdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
- .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};
- .phy_reset = true,
- .reset_gpio_port[0] = HSUSB1_RESET_GPIO,
- .reset_gpio_port[1] = HSUSB2_RESET_GPIO,
- .reset_gpio_port[2] = -EINVAL,
+static struct platform_device *usbhs_devices[] = {
+ &hsusb1_phy_device,
+ &hsusb1_reset_device,
+ &hsusb2_phy_device,
+ &hsusb2_reset_device,
};
static int __init cm_t3517_init_usbh(void)
@@ -213,6 +293,13 @@ static int __init cm_t3517_init_usbh(void)
msleep(1);
}
+ platform_add_devices(usbhs_devices, ARRAY_SIZE(usbhs_devices));
+
+ /* PHY on HSUSB Port 1 i.e. index 0 */
+ usb_bind_phy("ehci-omap.0", 0, "nop_usb_xceiv.1");
+ /* PHY on HSUSB Port 2 i.e. index 1 */
+ usb_bind_phy("ehci-omap.0", 1, "nop_usb_xceiv.2");
+
usbhs_init(&cm_t3517_ehci_pdata);
return 0;
--
1.7.4.1
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
