[]...
diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt
index 29a043e..4688265 100644
--- a/Documentation/devicetree/bindings/usb/omap-usb.txt
+++ b/Documentation/devicetree/bindings/usb/omap-usb.txt
@@ -15,6 +15,7 @@ OMAP MUSB GLUE
represents PERIPHERAL.
- power : Should be "50". This signifies the controller can supply upto
100mA when operating in host mode.
+ - usb-phy : the phandle for the PHY device
SOC specific device node entry
usb_otg_hs: usb_otg_hs@4a0ab000 {
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index 3705a81..cb07583 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -107,3 +107,9 @@
*/
ti,pulldowns = <0x03a1c4>;
};
+
+&usb_otg_hs {
+ interface_type = <0>;
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts
index e8ba1c2..afb9ba9 100644
--- a/arch/arm/boot/dts/omap3-evm.dts
+++ b/arch/arm/boot/dts/omap3-evm.dts
@@ -59,3 +59,9 @@
&twl_gpio {
ti,use-leds;
};
+
+&usb_otg_hs {
+ interface_type = <0>;
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap3-overo.dtsi b/arch/arm/boot/dts/omap3-overo.dtsi
index 89808ce..4b3d157 100644
--- a/arch/arm/boot/dts/omap3-overo.dtsi
+++ b/arch/arm/boot/dts/omap3-overo.dtsi
@@ -55,3 +55,9 @@
&twl_gpio {
ti,use-leds;
};
+
+&usb_otg_hs {
+ interface_type = <0>;
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index 1acc261..b6472f7 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -397,5 +397,17 @@
ti,timer-alwon;
ti,timer-secure;
};
+
+ usb_otg_hs: usb_otg_hs@480ab000 {
+ compatible = "ti,omap3-musb";
+ reg = <0x480ab000 0x1000>;
+ interrupts = <0 92 0x4>, <0 93 0x4>;
+ interrupt-names = "mc", "dma";
+ ti,hwmods = "usb_otg_hs";
+ usb-phy = <&usb2_phy>;
+ multipoint = <1>;
+ num_eps = <16>;
+ ram_bits = <12>;
Where are these bindings documented? The general convention is to use
a '-' for property names and not '_'
+ };
};
};
diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts
index 4122efe..612c9bb 100644
--- a/arch/arm/boot/dts/omap4-panda.dts
+++ b/arch/arm/boot/dts/omap4-panda.dts
@@ -206,3 +206,9 @@
&twl_usb_comparator {
usb-supply = <&vusb>;
};
+
+&usb_otg_hs {
+ interface_type = <1>;
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts
index 43e5258..582d7ee 100644
--- a/arch/arm/boot/dts/omap4-sdp.dts
+++ b/arch/arm/boot/dts/omap4-sdp.dts
@@ -428,3 +428,9 @@
&twl_usb_comparator {
usb-supply = <&vusb>;
};
+
+&usb_otg_hs {
+ interface_type = <1>;
+ mode = <3>;
+ power = <50>;
+};
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index c829d7e..5171739 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -542,5 +542,18 @@
reg-names = "control_dev_conf", "otghs_control";
ti,type = <1>;
};
+
+ usb_otg_hs: usb_otg_hs@4a0ab000 {
+ compatible = "ti,omap4-musb";
+ reg = <0x4a0ab000 0x7ff>;
+ interrupts = <0 92 0x4>, <0 93 0x4>;
+ interrupt-names = "mc", "dma";
+ ti,hwmods = "usb_otg_hs";
+ usb-phy = <&usb2_phy>;
+ multipoint = <1>;
+ num_eps = <16>;
+ ram_bits = <12>;
+ ti,has-mailbox;
+ };
};
};
diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi
index ed0bc95..398d2c3 100644
--- a/arch/arm/boot/dts/twl4030.dtsi
+++ b/arch/arm/boot/dts/twl4030.dtsi
@@ -67,7 +67,7 @@
#interrupt-cells = <1>;
};
- twl4030-usb {
+ usb2_phy: twl4030-usb {
compatible = "ti,twl4030-usb";
interrupts = <10>, <4>;
usb1v5-supply = <&vusb1v5>;
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
