Added a driver for usb3 phy that handles the interaction between usb phy
device and dwc3 controller.
This also includes device tree support for usb3 phy driver and
the documentation with device tree binding information is updated.
Currently writing to control module register is taken care in this
driver which will be removed once the control module driver is in place.
Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx>
Signed-off-by: Felipe Balbi <balbi@xxxxxx>
Signed-off-by: Moiz Sonasath <m-sonasath@xxxxxx>
---
Documentation/devicetree/bindings/usb/usb-phy.txt | 23 ++
drivers/usb/phy/Kconfig | 10 +
drivers/usb/phy/Makefile | 1 +
drivers/usb/phy/omap-usb3.c | 355 +++++++++++++++++++++
include/linux/usb/omap_usb.h | 23 ++
5 files changed, 412 insertions(+)
create mode 100644 drivers/usb/phy/omap-usb3.c
diff --git a/Documentation/devicetree/bindings/usb/usb-phy.txt b/Documentation/devicetree/bindings/usb/usb-phy.txt
index 48761a2..2229eab 100644
--- a/Documentation/devicetree/bindings/usb/usb-phy.txt
+++ b/Documentation/devicetree/bindings/usb/usb-phy.txt
@@ -17,3 +17,26 @@ usb2phy@4a0ad080 {
reg = <0x4a0ad080 0x58>;
ctrl-module = <&omap_control_usb>;
};
+
+OMAP USB3 PHY
+
+Required properties:
+ - compatible: Should be "ti,omap-usb3"
+ - reg : Address and length of the register set for the device.
+ - reg-names: The names of the register addresses corresponding to the registers
+ filled in "reg".
+
+Optional properties:
+ - ctrl-module : phandle of the control module used by PHY driver to power on
+ the PHY.
+
+This is usually a subnode of ocp2scp to which it is connected.
+
+usb3phy@4a084400 {
+ compatible = "ti,omap-usb3";
+ reg = <0x4a084400 0x80>,
+ <0x4a084800 0x64>,
+ <0x4a084c00 0x40>;
+ reg-names = "phy_rx", "phy_tx", "pll_ctrl";
+ ctrl-module = <&omap_control_usb>;
+};
diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 2122030..6566eae 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -15,6 +15,16 @@ config OMAP_USB2
The USB OTG controller communicates with the comparator using this
driver.
+config OMAP_USB3
+ tristate "OMAP USB3 PHY Driver"
+ select USB_OTG_UTILS
+ select OMAP_CONTROL_USB
+ help
+ Enable this to support the USB3 PHY that is part of SOC. This
+ driver takes care of all the PHY functionality apart from comparator.
+ This driver interacts with the "OMAP Control USB Driver" to power
+ on/off the PHY.
+
config OMAP_CONTROL_USB
tristate "OMAP CONTROL USB Driver"
depends on ARCH_OMAP2PLUS
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index 0dea4d2..6a07298 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -5,6 +5,7 @@
ccflags-$(CONFIG_USB_DEBUG) := -DDEBUG
obj-$(CONFIG_OMAP_USB2) += omap-usb2.o
+obj-$(CONFIG_OMAP_USB3) += omap-usb3.o
obj-$(CONFIG_OMAP_CONTROL_USB) += omap-control-usb.o
obj-$(CONFIG_USB_ISP1301) += isp1301.o
obj-$(CONFIG_MV_U3D_PHY) += mv_u3d_phy.o
diff --git a/drivers/usb/phy/omap-usb3.c b/drivers/usb/phy/omap-usb3.c
new file mode 100644
index 0000000..fadc0c2
--- /dev/null
+++ b/drivers/usb/phy/omap-usb3.c
@@ -0,0 +1,355 @@
+/*
+ * omap-usb3 - USB PHY, talking to dwc3 controller in OMAP.
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Author: Kishon Vijay Abraham I <kishon@xxxxxx>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/usb/omap_usb.h>
+#include <linux/of.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/pm_runtime.h>
+#include <linux/delay.h>
+#include <linux/usb/omap_control_usb.h>
+
+#define NUM_SYS_CLKS 5
+#define PLL_STATUS 0x00000004
+#define PLL_GO 0x00000008
+#define PLL_CONFIGURATION1 0x0000000C
+#define PLL_CONFIGURATION2 0x00000010
+#define PLL_CONFIGURATION3 0x00000014
+#define PLL_CONFIGURATION4 0x00000020
+
+#define PLL_REGM_MASK 0x001FFE00
+#define PLL_REGM_SHIFT 0x9
+#define PLL_REGM_F_MASK 0x0003FFFF
+#define PLL_REGM_F_SHIFT 0x0
+#define PLL_REGN_MASK 0x000001FE
+#define PLL_REGN_SHIFT 0x1
+#define PLL_SELFREQDCO_MASK 0x0000000E
+#define PLL_SELFREQDCO_SHIFT 0x1
+#define PLL_SD_MASK 0x0003FC00
+#define PLL_SD_SHIFT 0x9
+#define SET_PLL_GO 0x1
+#define PLL_TICOPWDN 0x10000
+#define PLL_LOCK 0x2
+#define PLL_IDLE 0x1
+
+/*
+ * This is an Empirical value that works, need to confirm the actual
+ * value required for the USB3PHY_PLL_CONFIGURATION2.PLL_IDLE status
+ * to be correctly reflected in the USB3PHY_PLL_STATUS register.
+ */
+# define PLL_IDLE_TIME 100;
+
+enum sys_clk_rate {
+ CLK_RATE_UNDEFINED = -1,
+ CLK_RATE_12MHZ,
+ CLK_RATE_16MHZ,
+ CLK_RATE_19MHZ,
+ CLK_RATE_26MHZ,
+ CLK_RATE_38MHZ
+};
+
+static struct usb_dpll_params omap_usb3_dpll_params[NUM_SYS_CLKS] = {
+ {1250, 5, 4, 20, 0}, /* 12 MHz */
+ {3125, 20, 4, 20, 0}, /* 16.8 MHz */
+ {1172, 8, 4, 20, 65537}, /* 19.2 MHz */
+ {1250, 12, 4, 20, 0}, /* 26 MHz */
+ {3125, 47, 4, 20, 92843}, /* 38.4 MHz */
+};
+
+static int omap_usb3_suspend(struct usb_phy *x, int suspend)
+{
+ struct omap_usb *phy = phy_to_omapusb(x);
+ int val;
+ int timeout = PLL_IDLE_TIME;
+
+ if (suspend && !phy->is_suspended) {
+ val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
+ val |= PLL_IDLE;
+ omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);
+
+ do {
+ val = omap_usb_readl(phy->pll_ctrl_base, PLL_STATUS);
+ if (val & PLL_TICOPWDN)
+ break;
+ udelay(1);
+ } while (--timeout);
+
+ omap_control_usb3_phy_power(phy->control_dev, 0);
+
+ phy->is_suspended = 1;
+ } else if (!suspend && phy->is_suspended) {
+ phy->is_suspended = 0;
+
+ val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
+ val &= ~PLL_IDLE;
+ omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);
+
+ do {
+ val = omap_usb_readl(phy->pll_ctrl_base, PLL_STATUS);
+ if (!(val & PLL_TICOPWDN))
+ break;
+ udelay(1);
+ } while (--timeout);
+ }
+
+ return 0;
+}
+
+static inline enum sys_clk_rate __get_sys_clk_index(unsigned long rate)
+{
+ switch (rate) {
+ case 12000000:
+ return CLK_RATE_12MHZ;
+ case 16800000:
+ return CLK_RATE_16MHZ;
+ case 19200000:
+ return CLK_RATE_19MHZ;
+ case 26000000:
+ return CLK_RATE_26MHZ;
+ case 38400000:
+ return CLK_RATE_38MHZ;
+ default:
+ return CLK_RATE_UNDEFINED;
+ }
+}
+
+static void omap_usb_dpll_relock(struct omap_usb *phy)
+{
+ u32 val;
+ unsigned long timeout;
+
+ omap_usb_writel(phy->pll_ctrl_base, PLL_GO, SET_PLL_GO);
+
+ timeout = jiffies + msecs_to_jiffies(20);
+ do {
+ val = omap_usb_readl(phy->pll_ctrl_base, PLL_STATUS);
+ if (val & PLL_LOCK)
+ break;
+ } while (!WARN_ON(time_after(jiffies, timeout)));
+}
+
+static int omap_usb_dpll_lock(struct omap_usb *phy)
+{
+ u32 val;
+ unsigned long rate;
+ enum sys_clk_rate clk_index;
+
+ rate = clk_get_rate(phy->sys_clk);
+ clk_index = __get_sys_clk_index(rate);
+
+ if (clk_index == CLK_RATE_UNDEFINED) {
+ pr_err("dpll cannot be locked for sys clk freq:%luHz\n", rate);
+ return -EINVAL;
+ }
+
+ val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
+ val &= ~PLL_REGN_MASK;
+ val |= omap_usb3_dpll_params[clk_index].n << PLL_REGN_SHIFT;
+ omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);
+
+ val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION2);
+ val &= ~PLL_SELFREQDCO_MASK;
+ val |= omap_usb3_dpll_params[clk_index].freq << PLL_SELFREQDCO_SHIFT;
+ omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION2, val);
+
+ val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION1);
+ val &= ~PLL_REGM_MASK;
+ val |= omap_usb3_dpll_params[clk_index].m << PLL_REGM_SHIFT;
+ omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION1, val);
+
+ val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION4);
+ val &= ~PLL_REGM_F_MASK;
+ val |= omap_usb3_dpll_params[clk_index].mf << PLL_REGM_F_SHIFT;
+ omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION4, val);
+
+ val = omap_usb_readl(phy->pll_ctrl_base, PLL_CONFIGURATION3);
+ val &= ~PLL_SD_MASK;
+ val |= omap_usb3_dpll_params[clk_index].sd << PLL_SD_SHIFT;
+ omap_usb_writel(phy->pll_ctrl_base, PLL_CONFIGURATION3, val);
+
+ omap_usb_dpll_relock(phy);
+
+ return 0;
+}
+
+static int omap_usb3_init(struct usb_phy *x)
+{
+ struct omap_usb *phy = phy_to_omapusb(x);
+
+ omap_usb_dpll_lock(phy);
+ omap_control_usb3_phy_power(phy->control_dev, 1);
+
+ return 0;
+}
+
+static int omap_usb3_probe(struct platform_device *pdev)
+{
+ struct omap_usb *phy;
+ struct resource *res;
+
+ phy = devm_kzalloc(&pdev->dev, sizeof(*phy), GFP_KERNEL);
+ if (!phy) {
+ dev_err(&pdev->dev, "unable to alloc mem for OMAP USB3 PHY\n");
+ return -ENOMEM;
+ }
+
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pll_ctrl");
+ phy->pll_ctrl_base = devm_request_and_ioremap(&pdev->dev, res);
+ if (!phy->pll_ctrl_base) {
+ dev_err(&pdev->dev, "ioremap of pll_ctrl failed\n");
+ return -ENOMEM;
+ }
+
+ phy->dev = &pdev->dev;
+
+ phy->phy.dev = phy->dev;
+ phy->phy.label = "omap-usb3";
+ phy->phy.init = omap_usb3_init;
+ phy->phy.set_suspend = omap_usb3_suspend;
+ phy->phy.type = USB_PHY_TYPE_USB3;
+
+ phy->is_suspended = 1;
+ phy->wkupclk = devm_clk_get(phy->dev, "usb_phy_cm_clk32k");
+ if (IS_ERR(phy->wkupclk)) {
+ dev_err(&pdev->dev, "unable to get usb_phy_cm_clk32k\n");
+ return PTR_ERR(phy->wkupclk);
+ }
+ clk_prepare(phy->wkupclk);
+
+ phy->optclk = devm_clk_get(phy->dev, "usb_otg_ss_refclk960m");
+ if (IS_ERR(phy->optclk)) {
+ dev_err(&pdev->dev, "unable to get usb_otg_ss_refclk960m\n");
+ return PTR_ERR(phy->optclk);
+ }
+ clk_prepare(phy->optclk);
+
+ phy->sys_clk = devm_clk_get(phy->dev, "sys_clkin");
+ if (IS_ERR(phy->sys_clk)) {
+ pr_err("%s: unable to get sys_clkin\n", __func__);
+ return -EINVAL;
+ }
+
+ phy->control_dev = omap_get_control_dev();
+ if (IS_ERR(phy->control_dev)) {
+ dev_dbg(&pdev->dev, "Failed to get control device\n");
+ return -ENODEV;
+ }
+
+ omap_control_usb3_phy_power(phy->control_dev, 0);
+ usb_add_phy_dev(&phy->phy);
+
+ platform_set_drvdata(pdev, phy);
+
+ pm_runtime_enable(phy->dev);
+ pm_runtime_get(&pdev->dev);
+
+ return 0;
+}
+
+static int omap_usb3_remove(struct platform_device *pdev)
+{
+ struct omap_usb *phy = platform_get_drvdata(pdev);
+
+ clk_unprepare(phy->wkupclk);
+ clk_unprepare(phy->optclk);
+ usb_remove_phy(&phy->phy);
+ if (!pm_runtime_suspended(&pdev->dev))
+ pm_runtime_put(&pdev->dev);
+ pm_runtime_disable(&pdev->dev);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_RUNTIME
+
+static int omap_usb3_runtime_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct omap_usb *phy = platform_get_drvdata(pdev);
+
+ clk_disable(phy->wkupclk);
+ clk_disable(phy->optclk);
+
+ return 0;
+}
+
+static int omap_usb3_runtime_resume(struct device *dev)
+{
+ u32 ret = 0;
+ struct platform_device *pdev = to_platform_device(dev);
+ struct omap_usb *phy = platform_get_drvdata(pdev);
+
+ ret = clk_enable(phy->optclk);
+ if (ret) {
+ dev_err(phy->dev, "Failed to enable optclk %d\n", ret);
+ goto err1;
+ }
+
+ ret = clk_enable(phy->wkupclk);
+ if (ret) {
+ dev_err(phy->dev, "Failed to enable wkupclk %d\n", ret);
+ goto err2;
+ }
+
+ return 0;
+
+err2:
+ clk_disable(phy->optclk);
+
+err1:
+ return ret;
+}
+
+static const struct dev_pm_ops omap_usb3_pm_ops = {
+ SET_RUNTIME_PM_OPS(omap_usb3_runtime_suspend, omap_usb3_runtime_resume,
+ NULL)
+};
+
+#define DEV_PM_OPS (&omap_usb3_pm_ops)
+#else
+#define DEV_PM_OPS NULL
+#endif
+
+#ifdef CONFIG_OF
+static const struct of_device_id omap_usb3_id_table[] = {
+ { .compatible = "ti,omap-usb3" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, omap_usb3_id_table);
+#endif
+
+static struct platform_driver omap_usb3_driver = {
+ .probe = omap_usb3_probe,
+ .remove = omap_usb3_remove,
+ .driver = {
+ .name = "omap-usb3",
+ .owner = THIS_MODULE,
+ .pm = DEV_PM_OPS,
+ .of_match_table = of_match_ptr(omap_usb3_id_table),
+ },
+};
+
+module_platform_driver(omap_usb3_driver);
+
+MODULE_ALIAS("platform: omap_usb3");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_DESCRIPTION("OMAP USB3 phy driver");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/usb/omap_usb.h b/include/linux/usb/omap_usb.h
index 3db9b53..6ae2936 100644
--- a/include/linux/usb/omap_usb.h
+++ b/include/linux/usb/omap_usb.h
@@ -19,14 +19,26 @@
#ifndef __DRIVERS_OMAP_USB2_H
#define __DRIVERS_OMAP_USB2_H
+#include <linux/io.h>
#include <linux/usb/otg.h>
+struct usb_dpll_params {
+ u16 m;
+ u8 n;
+ u8 freq:3;
+ u8 sd;
+ u32 mf;
+};
+
struct omap_usb {
struct usb_phy phy;
struct phy_companion *comparator;
+ void __iomem *pll_ctrl_base;
struct device *dev;
struct device *control_dev;
struct clk *wkupclk;
+ struct clk *sys_clk;
+ struct clk *optclk;
u8 is_suspended:1;
};
@@ -41,4 +53,15 @@ static inline int omap_usb2_set_comparator(struct phy_companion *comparator)
}
#endif
+static inline u32 omap_usb_readl(void __iomem *addr, unsigned offset)
+{
+ return __raw_readl(addr + offset);
+}
+
+static inline void omap_usb_writel(void __iomem *addr, unsigned offset,
+ u32 data)
+{
+ __raw_writel(data, addr + offset);
+}
+
#endif /* __DRIVERS_OMAP_USB_H */
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
