Re: [RESEND PATCH V2] mmc: omap_hsmmc: Enable HSPE bit for high speed cards

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 10/31/2012 3:34 PM, Felipe Balbi wrote:
Hi,

On Wed, Oct 31, 2012 at 01:58:35PM +0530, Hebbar, Gururaja wrote:
HSMMC IP on AM33xx need a special setting to handle High-speed cards.
Other platforms like TI81xx, OMAP4 may need this as-well. This depends
on the HSMMC IP timing closure done for the high speed cards.

 From AM335x TRM (SPRUH73F - 18.3.12 Output Signals Generation)

The MMC/SD/SDIO output signals can be driven on either falling edge or
rising edge depending on the SD_HCTL[2] HSPE bit. This feature allows
to reach better timing performance, and thus to increase data transfer
frequency.

There are few pre-requisites for enabling the HSPE bit
- Controller should support High-Speed-Enable Bit and
- Controller should not be using DDR Mode and
- Controller should advertise that it supports High Speed in
   capabilities register and
- MMC/SD clock coming out of controller > 25MHz

Note:
The implementation reuses the output of calc_divisor() so as to reduce
code addition.

Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@xxxxxx>
---
Rebased on mmc-next (v3.7.0-rc1)
Only Build tested since EDMA support for AM335x is not yet added

Changes in V2
	- Added note in commit message about code re-use
	- replaced ((a & BIT(n) == BIT(n))) with (a & BIT(n)) since
	  effectively both are same.

:100644 100644 be76a23... ed271fc... M	Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
:100644 100644 8b4e4f2... 346af5b... M	arch/arm/plat-omap/include/plat/mmc.h
:100644 100644 54bfd0c... 5ea4c9d... M	drivers/mmc/host/omap_hsmmc.c
  .../devicetree/bindings/mmc/ti-omap-hsmmc.txt      |    1 +
  arch/arm/plat-omap/include/plat/mmc.h              |    1 +
  drivers/mmc/host/omap_hsmmc.c                      |   30 +++++++++++++++++++-
  3 files changed, 31 insertions(+), 1 deletions(-)

diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
index be76a23..ed271fc 100644
--- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
+++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
@@ -19,6 +19,7 @@ ti,dual-volt: boolean, supports dual voltage cards
  "supply-name" examples are "vmmc", "vmmc_aux" etc
  ti,non-removable: non-removable slot (like eMMC)
  ti,needs-special-reset: Requires a special softreset sequence
+ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed
Example:
  	mmc1: mmc@0x4809c000 {
diff --git a/arch/arm/plat-omap/include/plat/mmc.h b/arch/arm/plat-omap/include/plat/mmc.h
index 8b4e4f2..346af5b 100644
--- a/arch/arm/plat-omap/include/plat/mmc.h
+++ b/arch/arm/plat-omap/include/plat/mmc.h
@@ -126,6 +126,7 @@ struct omap_mmc_platform_data {
  		/* we can put the features above into this variable */
  #define HSMMC_HAS_PBIAS		(1 << 0)
  #define HSMMC_HAS_UPDATED_RESET	(1 << 1)
+#define HSMMC_HAS_HSPE_SUPPORT	(1 << 2)
  		unsigned features;
int switch_pin; /* gpio (card detect) */
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 54bfd0c..5ea4c9d 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -62,6 +62,7 @@
#define VS18 (1 << 26)
  #define VS30			(1 << 25)
+#define HSS			(1 << 21)
  #define SDVS18			(0x5 << 9)
  #define SDVS30			(0x6 << 9)
  #define SDVS33			(0x7 << 9)
@@ -89,6 +90,7 @@
  #define MSBS			(1 << 5)
  #define BCE			(1 << 1)
  #define FOUR_BIT		(1 << 1)
+#define HSPE			(1 << 2)
  #define DDR			(1 << 19)
  #define DW8			(1 << 5)
  #define CC			0x1
@@ -489,6 +491,7 @@ static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host)
  	struct mmc_ios *ios = &host->mmc->ios;
  	unsigned long regval;
  	unsigned long timeout;
+	unsigned long clkdiv;
dev_vdbg(mmc_dev(host->mmc), "Set clock to %uHz\n", ios->clock); @@ -496,7 +499,8 @@ static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host) regval = OMAP_HSMMC_READ(host->base, SYSCTL);
  	regval = regval & ~(CLKD_MASK | DTO_MASK);
-	regval = regval | (calc_divisor(host, ios) << 6) | (DTO << 16);
+	clkdiv = calc_divisor(host, ios);
+	regval = regval | (clkdiv << 6) | (DTO << 16);
  	OMAP_HSMMC_WRITE(host->base, SYSCTL, regval);
  	OMAP_HSMMC_WRITE(host->base, SYSCTL,
  		OMAP_HSMMC_READ(host->base, SYSCTL) | ICE);
@@ -507,6 +511,27 @@ static void omap_hsmmc_set_clock(struct omap_hsmmc_host *host)
  		&& time_before(jiffies, timeout))
  		cpu_relax();
+ /*
+	 * Enable High-Speed Support
+	 * Pre-Requisites
+	 *	- Controller should support High-Speed-Enable Bit
+	 *	- Controller should not be using DDR Mode
+	 *	- Controller should advertise that it supports High Speed
+	 *	  in capabilities register
+	 *	- MMC/SD clock coming out of controller > 25MHz
+	 */
+	if ((mmc_slot(host).features & HSMMC_HAS_HSPE_SUPPORT) &&
+	    (ios->timing != MMC_TIMING_UHS_DDR50) &&
+	    (OMAP_HSMMC_READ(host->base, CAPA) & HSS)) {
+		regval = OMAP_HSMMC_READ(host->base, HCTL);
+		if (clkdiv && (clk_get_rate(host->fclk)/clkdiv) > 25000000)
that clk rate could be a symbolic define.

Ok will update as below and re-use

#define OMAP_HSMMC_CLKOUT   25000000

+			regval |= HSPE;
+		else
+			regval &= ~HSPE;
+
+		OMAP_HSMMC_WRITE(host->base, HCTL, regval);
+	}
+
  	omap_hsmmc_start_clock(host);
  }
@@ -1700,6 +1725,9 @@ static struct omap_mmc_platform_data *of_get_hsmmc_pdata(struct device *dev)
  	if (of_find_property(np, "ti,needs-special-reset", NULL))
  		pdata->slots[0].features |= HSMMC_HAS_UPDATED_RESET;
+ if (of_find_property(np, "ti,needs-special-hs-handling", NULL))
+		pdata->slots[0].features |= HSMMC_HAS_HSPE_SUPPORT;
this could be of_property_read_bool().
Ok will change.



--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux