On 10/25/2012 02:00 AM, Santosh Shilimkar wrote:
> On Thursday 25 October 2012 04:24 AM, Jon Hunter wrote:
>>
>> On 10/24/2012 12:10 PM, Kevin Hilman wrote:
>>> From: Kevin Hilman <khilman@xxxxxx>
>>>
>>> When a GPIO bank is freed or shutdown, ensure that the banks
>>> dbck_enable_mask is cleared also. Otherwise, context restore on
>>> subsequent off-mode transition will restore previous value from the
>>> shadow copies (bank->context.debounce*) leading to mismatch state
>>> between driver state and hardware state.
>>>
>>> This was discovered when board code was doing
>>>
>>> gpio_request_one()
>>> gpio_set_debounce()
>>> gpio_free()
>>>
>>> which was leaving the GPIO debounce settings in a confused state. If
>>> that GPIO bank is subsequently used with off-mode enabled, bogus state
>>> would be restored, leaving GPIO debounce enabled which then prevented
>>> the CORE powerdomain from transitioning.
>>>
>>> To fix, ensure that bank->dbck_enable_mask is cleared when the bank
>>> is freed/shutdown so debounce state doesn't persist.
> The freed part is fine but I don't understand why it needs to be done
> on _a_ gpio irq shutdown callback where IRQs related configuration
> on that one GPIO needs to be cleared. De-bounce clock is surely not IRQ
> related configuration.
If we are freeing the IRQs related to gpio and resetting the gpio, then
I don't see why we should not. We should not leave the debounce clock on
if these gpios are no longer being used.
>>> Special thanks to Grazvydas Ignotas for pointing out a bug in an
>>> earlier version that would've disabled debounce on any runtime PM
>>> transition.
>>>
>>> Reported-by: Paul Walmsley <paul@xxxxxxxxx>
>>> Cc: Igor Grinberg <grinberg@xxxxxxxxxxxxxx>
>>> Cc: Grazvydas Ignotas <notasas@xxxxxxxxx>
>>> Signed-off-by: Kevin Hilman <khilman@xxxxxx>
>>> ---
>>> v2: only clear mask in free/shutdown, not in runtime PM paths,
>>> clarified changelog
>>> Applies on v3.7-rc2.
>>>
>>> drivers/gpio/gpio-omap.c | 1 +
>>> 1 file changed, 1 insertion(+)
>>>
>>> diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
>>> index 94cbc84..113b167 100644
>>> --- a/drivers/gpio/gpio-omap.c
>>> +++ b/drivers/gpio/gpio-omap.c
>>> @@ -539,6 +539,7 @@ static void _reset_gpio(struct gpio_bank *bank,
>>> int gpio)
>>> _set_gpio_irqenable(bank, gpio, 0);
>>> _clear_gpio_irqstatus(bank, gpio);
>>> _set_gpio_triggering(bank, GPIO_INDEX(bank, gpio), IRQ_TYPE_NONE);
>>> + bank->dbck_enable_mask = 0;
>>> }
>>
>> Does this need to be ...
>>
>> + bank->dbck_enable_mask &= ~(GPIO_BIT(bank, gpio));
>> + _gpio_dbck_disable(bank);
>>
> Yes, its a per bank clock. There is an alternate. See below.
>
>> There could be more than one gpio using debounce and so we should only
>> clear the appropriate bit. Also after clearing a bit we could see if we
>> can disable the debounce clock too.
>>
> When I mentioned the clearing in gpio_free() path will do trick, I had
> something like below in mind.
>
> diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
> index dee2856..8574105 100644
> --- a/drivers/gpio/gpio-omap.c
> +++ b/drivers/gpio/gpio-omap.c
> @@ -629,8 +629,10 @@ static void omap_gpio_free(struct gpio_chip *chip,
> unsigned offset)
> * If this is the last gpio to be freed in the bank,
> * disable the bank module.
> */
> - if (!bank->mod_usage)
> + if (!bank->mod_usage) {
> + bank->dbck_enable_mask = 0;
> pm_runtime_put(bank->dev);
> + }
However, with this we could be leaving the debounce clock on longer than
needed. I think we need to call _gpio_dbck_disable() each time we free a
gpio and this function will determine if it can turn off the debounce
clock.
In fact, there appears to be another bug in the current driver, that we
do not clear the debounce_en register when freeing the gpio. Your patch
addresses this, but I think that debounce should be disabled when a gpio
is freed and not just when the last one is freed.
Also, with the above change, can't we still run into the original
problem? In other words, if a gpio is freed, but there is still another
one active in the back that is not using debounce, then we could restore
a incorrect debounce context because we have not clean-up the debounce
settings?
So may be we need to add a _clear_gpio_debounce() function and
call this when freeing a gpio.
Cheers
Jon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
