Move OMAP3xxx-specific PRM functions & macros into prm3xxx.[ch] and
OMAP2xxx-specific macros into prm2xxx.h. (prm2xxx.c will be created
by a subsequent patch when it's needed.) Move basic PRM register
access functions into static inline functions in prm2xxx_3xxx.h, leaving
only OMAP2/3 hardreset functions in prm2xxx_3xxx.c.
Also clarify the initcall function naming to reinforce that this code
is specifically for the PRM IP block.
This is in preparation for the upcoming powerdomain series and the
upcoming move of this code to drivers/.
Signed-off-by: Paul Walmsley <paul@xxxxxxxxx>
---
arch/arm/mach-omap2/Makefile | 100 +++++++-----
arch/arm/mach-omap2/control.c | 2
arch/arm/mach-omap2/omap_hwmod.c | 2
arch/arm/mach-omap2/pm24xx.c | 2
arch/arm/mach-omap2/pm34xx.c | 2
arch/arm/mach-omap2/prm-regbits-24xx.h | 2
arch/arm/mach-omap2/prm-regbits-34xx.h | 2
arch/arm/mach-omap2/prm2xxx.h | 122 +++++++++++++++
arch/arm/mach-omap2/prm2xxx_3xxx.c | 265 --------------------------------
arch/arm/mach-omap2/prm2xxx_3xxx.h | 256 ++++++-------------------------
arch/arm/mach-omap2/prm3xxx.c | 164 ++------------------
arch/arm/mach-omap2/prm3xxx.h | 158 +++++++++++++++++++
arch/arm/mach-omap2/prm44xx.c | 15 +-
arch/arm/mach-omap2/sdrc2xxx.c | 2
arch/arm/mach-omap2/sleep34xx.S | 2
arch/arm/mach-omap2/sram242x.S | 2
arch/arm/mach-omap2/sram243x.S | 2
17 files changed, 421 insertions(+), 679 deletions(-)
create mode 100644 arch/arm/mach-omap2/prm2xxx.h
copy arch/arm/mach-omap2/{prm2xxx_3xxx.c => prm3xxx.c} (57%)
create mode 100644 arch/arm/mach-omap2/prm3xxx.h
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index fe40d9e..20849604 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -4,30 +4,36 @@
# Common support
obj-y := id.o io.o control.o mux.o devices.o serial.o gpmc.o timer.o pm.o \
- common.o gpio.o dma.o wd_timer.o display.o i2c.o hdq1w.o omap_hwmod.o
+ common.o gpio.o dma.o wd_timer.o display.o i2c.o hdq1w.o
-# INTCPS IP block support - XXX should be moved to drivers/
-obj-$(CONFIG_ARCH_OMAP2) += irq.o
-obj-$(CONFIG_ARCH_OMAP3) += irq.o
-obj-$(CONFIG_SOC_AM33XX) += irq.o
+omap-2-3-common = irq.o
+hwmod-common = omap_hwmod.o \
+ omap_hwmod_common_data.o
+clock-common = clock.o clock_common_data.o \
+ clkt_dpll.o clkt_clksel.o
+secure-common = omap-smc.o omap-secure.o
-# Secure monitor API support
-obj-$(CONFIG_ARCH_OMAP3) += omap-smc.o omap-secure.o
-obj-$(CONFIG_ARCH_OMAP4) += omap-smc.o omap-secure.o
-obj-$(CONFIG_SOC_OMAP5) += omap-smc.o omap-secure.o
+obj-$(CONFIG_ARCH_OMAP2) += $(omap-2-3-common) $(hwmod-common)
+obj-$(CONFIG_ARCH_OMAP3) += $(omap-2-3-common) $(hwmod-common) $(secure-common)
+obj-$(CONFIG_ARCH_OMAP4) += prm44xx.o $(hwmod-common) $(secure-common)
+obj-$(CONFIG_SOC_AM33XX) += irq.o $(hwmod-common)
+obj-$(CONFIG_SOC_OMAP5) += prm44xx.o $(hwmod-common) $(secure-common)
ifneq ($(CONFIG_SND_OMAP_SOC_MCBSP),)
obj-y += mcbsp.o
endif
-obj-$(CONFIG_TWL4030_CORE) += omap_twl.o
+obj-$(CONFIG_TWL4030_CORE) += omap_twl.o
+obj-$(CONFIG_SOC_HAS_OMAP2_SDRC) += sdrc.o
# SMP support ONLY available for OMAP4
obj-$(CONFIG_SMP) += omap-smp.o omap-headsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += omap-hotplug.o
-obj-$(CONFIG_ARCH_OMAP4) += omap4-common.o omap-wakeupgen.o
-obj-$(CONFIG_SOC_OMAP5) += omap4-common.o omap-wakeupgen.o
+omap-4-5-common = omap4-common.o omap-wakeupgen.o \
+ sleep44xx.o
+obj-$(CONFIG_ARCH_OMAP4) += $(omap-4-5-common)
+obj-$(CONFIG_SOC_OMAP5) += $(omap-4-5-common)
plus_sec := $(call as-instr,.arch_extension sec,+sec)
AFLAGS_omap-headsmp.o :=-Wa,-march=armv7-a$(plus_sec)
@@ -52,7 +58,6 @@ obj-$(CONFIG_ARCH_OMAP4) += mux44xx.o
# SMS/SDRC
obj-$(CONFIG_ARCH_OMAP2) += sdrc2xxx.o
# obj-$(CONFIG_ARCH_OMAP3) += sdrc3xxx.o
-obj-$(CONFIG_SOC_HAS_OMAP2_SDRC) += sdrc.o
# OPP table initialization
ifeq ($(CONFIG_PM_OPP),y)
@@ -63,15 +68,15 @@ endif
# Power Management
ifeq ($(CONFIG_PM),y)
-obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o sleep24xx.o
+obj-$(CONFIG_ARCH_OMAP2) += pm24xx.o
+obj-$(CONFIG_ARCH_OMAP2) += sleep24xx.o
obj-$(CONFIG_ARCH_OMAP3) += pm34xx.o sleep34xx.o
obj-$(CONFIG_ARCH_OMAP4) += pm44xx.o omap-mpuss-lowpower.o
-obj-$(CONFIG_ARCH_OMAP4) += sleep44xx.o
-obj-$(CONFIG_SOC_OMAP5) += omap-mpuss-lowpower.o sleep44xx.o
+obj-$(CONFIG_SOC_OMAP5) += omap-mpuss-lowpower.o
obj-$(CONFIG_PM_DEBUG) += pm-debug.o
obj-$(CONFIG_POWER_AVS_OMAP) += sr_device.o
-obj-$(CONFIG_POWER_AVS_OMAP_CLASS3) += smartreflex-class3.o
+obj-$(CONFIG_POWER_AVS_OMAP_CLASS3) += smartreflex-class3.o
AFLAGS_sleep24xx.o :=-Wa,-march=armv6
AFLAGS_sleep34xx.o :=-Wa,-march=armv7-a$(plus_sec)
@@ -83,76 +88,88 @@ endif
endif
ifeq ($(CONFIG_CPU_IDLE),y)
-obj-$(CONFIG_ARCH_OMAP3) += cpuidle34xx.o
-obj-$(CONFIG_ARCH_OMAP4) += cpuidle44xx.o
+obj-$(CONFIG_ARCH_OMAP3) += cpuidle34xx.o
+obj-$(CONFIG_ARCH_OMAP4) += cpuidle44xx.o
endif
# PRCM
obj-y += prcm.o prm_common.o
obj-$(CONFIG_ARCH_OMAP2) += cm2xxx_3xxx.o prm2xxx_3xxx.o
obj-$(CONFIG_ARCH_OMAP3) += cm2xxx_3xxx.o prm2xxx_3xxx.o
+obj-$(CONFIG_ARCH_OMAP3) += prm3xxx.o
obj-$(CONFIG_ARCH_OMAP3) += vc3xxx_data.o vp3xxx_data.o
obj-$(CONFIG_SOC_AM33XX) += prm33xx.o cm33xx.o
omap-prcm-4-5-common = cminst44xx.o cm44xx.o prm44xx.o \
prcm_mpu44xx.o prminst44xx.o \
- vc44xx_data.o vp44xx_data.o \
- prm44xx.o
+ vc44xx_data.o vp44xx_data.o
obj-$(CONFIG_ARCH_OMAP4) += $(omap-prcm-4-5-common)
obj-$(CONFIG_SOC_OMAP5) += $(omap-prcm-4-5-common)
# OMAP voltage domains
-obj-y += voltage.o vc.o vp.o
+voltagedomain-common := voltage.o vc.o vp.o
+obj-$(CONFIG_ARCH_OMAP2) += $(voltagedomain-common)
obj-$(CONFIG_ARCH_OMAP2) += voltagedomains2xxx_data.o
+obj-$(CONFIG_ARCH_OMAP3) += $(voltagedomain-common)
obj-$(CONFIG_ARCH_OMAP3) += voltagedomains3xxx_data.o
+obj-$(CONFIG_ARCH_OMAP4) += $(voltagedomain-common)
obj-$(CONFIG_ARCH_OMAP4) += voltagedomains44xx_data.o
-obj-$(CONFIG_SOC_AM33XX) += voltagedomains33xx_data.o
+obj-$(CONFIG_SOC_AM33XX) += $(voltagedomain-common)
+obj-$(CONFIG_SOC_AM33XX) += voltagedomains33xx_data.o
+obj-$(CONFIG_SOC_OMAP5) += $(voltagedomain-common)
# OMAP powerdomain framework
-obj-y += powerdomain.o powerdomain-common.o
+powerdomain-common += powerdomain.o powerdomain-common.o
+obj-$(CONFIG_ARCH_OMAP2) += $(powerdomain-common)
obj-$(CONFIG_ARCH_OMAP2) += powerdomains2xxx_data.o
-obj-$(CONFIG_ARCH_OMAP2) += powerdomain2xxx_3xxx.o
obj-$(CONFIG_ARCH_OMAP2) += powerdomains2xxx_3xxx_data.o
-obj-$(CONFIG_ARCH_OMAP3) += powerdomain2xxx_3xxx.o
+obj-$(CONFIG_ARCH_OMAP3) += $(powerdomain-common)
obj-$(CONFIG_ARCH_OMAP3) += powerdomains3xxx_data.o
obj-$(CONFIG_ARCH_OMAP3) += powerdomains2xxx_3xxx_data.o
-obj-$(CONFIG_ARCH_OMAP4) += powerdomain44xx.o
+obj-$(CONFIG_ARCH_OMAP4) += $(powerdomain-common)
obj-$(CONFIG_ARCH_OMAP4) += powerdomains44xx_data.o
-obj-$(CONFIG_SOC_AM33XX) += powerdomain33xx.o
+obj-$(CONFIG_SOC_AM33XX) += $(powerdomain-common)
obj-$(CONFIG_SOC_AM33XX) += powerdomains33xx_data.o
-obj-$(CONFIG_SOC_OMAP5) += powerdomain44xx.o
+obj-$(CONFIG_SOC_OMAP5) += $(powerdomain-common)
# PRCM clockdomain control
-obj-y += clockdomain.o
+clockdomain-common += clockdomain.o
+obj-$(CONFIG_ARCH_OMAP2) += $(clockdomain-common)
obj-$(CONFIG_ARCH_OMAP2) += clockdomain2xxx_3xxx.o
obj-$(CONFIG_ARCH_OMAP2) += clockdomains2xxx_3xxx_data.o
obj-$(CONFIG_SOC_OMAP2420) += clockdomains2420_data.o
obj-$(CONFIG_SOC_OMAP2430) += clockdomains2430_data.o
+obj-$(CONFIG_ARCH_OMAP3) += $(clockdomain-common)
obj-$(CONFIG_ARCH_OMAP3) += clockdomain2xxx_3xxx.o
obj-$(CONFIG_ARCH_OMAP3) += clockdomains2xxx_3xxx_data.o
obj-$(CONFIG_ARCH_OMAP3) += clockdomains3xxx_data.o
+obj-$(CONFIG_ARCH_OMAP4) += $(clockdomain-common)
obj-$(CONFIG_ARCH_OMAP4) += clockdomain44xx.o
obj-$(CONFIG_ARCH_OMAP4) += clockdomains44xx_data.o
+obj-$(CONFIG_SOC_AM33XX) += $(clockdomain-common)
obj-$(CONFIG_SOC_AM33XX) += clockdomain33xx.o
obj-$(CONFIG_SOC_AM33XX) += clockdomains33xx_data.o
+obj-$(CONFIG_SOC_OMAP5) += $(clockdomain-common)
obj-$(CONFIG_SOC_OMAP5) += clockdomain44xx.o
# Clock framework
-obj-y += clock.o clock_common_data.o \
- clkt_dpll.o clkt_clksel.o
-obj-$(CONFIG_ARCH_OMAP2) += clock2xxx.o
-obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpllcore.o clkt2xxx_sys.o
+obj-$(CONFIG_ARCH_OMAP2) += $(clock-common) clock2xxx.o
+obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_sys.o
+obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpllcore.o
obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_virt_prcm_set.o
obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_apll.o clkt2xxx_osc.o
obj-$(CONFIG_ARCH_OMAP2) += clkt2xxx_dpll.o clkt_iclk.o
obj-$(CONFIG_SOC_OMAP2420) += clock2420_data.o
obj-$(CONFIG_SOC_OMAP2430) += clock2430.o clock2430_data.o
-obj-$(CONFIG_ARCH_OMAP3) += clock3xxx.o
+obj-$(CONFIG_ARCH_OMAP3) += $(clock-common) clock3xxx.o
obj-$(CONFIG_ARCH_OMAP3) += clock34xx.o clkt34xx_dpll3m2.o
-obj-$(CONFIG_ARCH_OMAP3) += clock3517.o clock36xx.o clkt_iclk.o
+obj-$(CONFIG_ARCH_OMAP3) += clock3517.o clock36xx.o
obj-$(CONFIG_ARCH_OMAP3) += dpll3xxx.o clock3xxx_data.o
-obj-$(CONFIG_ARCH_OMAP4) += clock44xx_data.o
+obj-$(CONFIG_ARCH_OMAP3) += clkt_iclk.o
+obj-$(CONFIG_ARCH_OMAP4) += $(clock-common) clock44xx_data.o
obj-$(CONFIG_ARCH_OMAP4) += dpll3xxx.o dpll44xx.o
-obj-$(CONFIG_SOC_AM33XX) += dpll3xxx.o clock33xx_data.o
+obj-$(CONFIG_SOC_AM33XX) += $(clock-common) dpll3xxx.o
+obj-$(CONFIG_SOC_AM33XX) += clock33xx_data.o
+obj-$(CONFIG_SOC_OMAP5) += $(clock-common)
obj-$(CONFIG_SOC_OMAP5) += dpll3xxx.o dpll44xx.o
# OMAP2 clock rate set data (old "OPP" data)
@@ -160,7 +177,6 @@ obj-$(CONFIG_SOC_OMAP2420) += opp2420_data.o
obj-$(CONFIG_SOC_OMAP2430) += opp2430_data.o
# hwmod data
-obj-y += omap_hwmod_common_data.o
obj-$(CONFIG_SOC_OMAP2420) += omap_hwmod_2xxx_ipblock_data.o
obj-$(CONFIG_SOC_OMAP2420) += omap_hwmod_2xxx_3xxx_ipblock_data.o
obj-$(CONFIG_SOC_OMAP2420) += omap_hwmod_2xxx_interconnect_data.o
@@ -206,10 +222,10 @@ obj-$(CONFIG_MACH_OMAP_H4) += board-h4.o
obj-$(CONFIG_MACH_OMAP_2430SDP) += board-2430sdp.o
obj-$(CONFIG_MACH_OMAP_APOLLON) += board-apollon.o
obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o
-obj-$(CONFIG_MACH_DEVKIT8000) += board-devkit8000.o
+obj-$(CONFIG_MACH_DEVKIT8000) += board-devkit8000.o
obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o
-obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o
-obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o
+obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o
+obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o
obj-$(CONFIG_MACH_ENCORE) += board-omap3encore.o
obj-$(CONFIG_MACH_OVERO) += board-overo.o
obj-$(CONFIG_MACH_OMAP3EVM) += board-omap3evm.o
diff --git a/arch/arm/mach-omap2/control.c b/arch/arm/mach-omap2/control.c
index d1ff839..1220e0e 100644
--- a/arch/arm/mach-omap2/control.c
+++ b/arch/arm/mach-omap2/control.c
@@ -22,7 +22,7 @@
#include "common.h"
#include "cm-regbits-34xx.h"
#include "prm-regbits-34xx.h"
-#include "prm2xxx_3xxx.h"
+#include "prm3xxx.h"
#include "cm2xxx_3xxx.h"
#include "sdrc.h"
#include "pm.h"
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index b969ab1..525c58d 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -150,7 +150,7 @@
#include "cm2xxx_3xxx.h"
#include "cminst44xx.h"
#include "cm33xx.h"
-#include "prm2xxx_3xxx.h"
+#include "prm3xxx.h"
#include "prm44xx.h"
#include "prm33xx.h"
#include "prminst44xx.h"
diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c
index 8af6cd6..78405a7 100644
--- a/arch/arm/mach-omap2/pm24xx.c
+++ b/arch/arm/mach-omap2/pm24xx.c
@@ -41,7 +41,7 @@
#include <plat/dma.h>
#include "common.h"
-#include "prm2xxx_3xxx.h"
+#include "prm2xxx.h"
#include "prm-regbits-24xx.h"
#include "cm2xxx_3xxx.h"
#include "cm-regbits-24xx.h"
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index ba670db..c02c9ca 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -48,7 +48,7 @@
#include "cm-regbits-34xx.h"
#include "prm-regbits-34xx.h"
-#include "prm2xxx_3xxx.h"
+#include "prm3xxx.h"
#include "pm.h"
#include "sdrc.h"
#include "control.h"
diff --git a/arch/arm/mach-omap2/prm-regbits-24xx.h b/arch/arm/mach-omap2/prm-regbits-24xx.h
index 6ac9661..bd70a5a 100644
--- a/arch/arm/mach-omap2/prm-regbits-24xx.h
+++ b/arch/arm/mach-omap2/prm-regbits-24xx.h
@@ -14,7 +14,7 @@
* published by the Free Software Foundation.
*/
-#include "prm2xxx_3xxx.h"
+#include "prm2xxx.h"
/* Bits shared between registers */
diff --git a/arch/arm/mach-omap2/prm-regbits-34xx.h b/arch/arm/mach-omap2/prm-regbits-34xx.h
index 64c087a..073d4db 100644
--- a/arch/arm/mach-omap2/prm-regbits-34xx.h
+++ b/arch/arm/mach-omap2/prm-regbits-34xx.h
@@ -14,7 +14,7 @@
#define __ARCH_ARM_MACH_OMAP2_PRM_REGBITS_34XX_H
-#include "prm2xxx_3xxx.h"
+#include "prm3xxx.h"
/* Shared register bits */
diff --git a/arch/arm/mach-omap2/prm2xxx.h b/arch/arm/mach-omap2/prm2xxx.h
new file mode 100644
index 0000000..6490e1a
--- /dev/null
+++ b/arch/arm/mach-omap2/prm2xxx.h
@@ -0,0 +1,122 @@
+/*
+ * OMAP2xxx Power/Reset Management (PRM) register definitions
+ *
+ * Copyright (C) 2007-2009, 2011-2012 Texas Instruments, Inc.
+ * Copyright (C) 2008-2010 Nokia Corporation
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * The PRM hardware modules on the OMAP2/3 are quite similar to each
+ * other. The PRM on OMAP4 has a new register layout, and is handled
+ * in a separate file.
+ */
+#ifndef __ARCH_ARM_MACH_OMAP2_PRM2XXX_H
+#define __ARCH_ARM_MACH_OMAP2_PRM2XXX_H
+
+#include "prcm-common.h"
+#include "prm.h"
+#include "prm2xxx_3xxx.h"
+
+#define OMAP2420_PRM_REGADDR(module, reg) \
+ OMAP2_L4_IO_ADDRESS(OMAP2420_PRM_BASE + (module) + (reg))
+#define OMAP2430_PRM_REGADDR(module, reg) \
+ OMAP2_L4_IO_ADDRESS(OMAP2430_PRM_BASE + (module) + (reg))
+
+/*
+ * OMAP2-specific global PRM registers
+ * Use __raw_{read,write}l() with these registers.
+ *
+ * With a few exceptions, these are the register names beginning with
+ * PRCM_* on 24xx. (The exceptions are the IRQSTATUS and IRQENABLE
+ * bits.)
+ *
+ */
+
+#define OMAP2_PRCM_REVISION_OFFSET 0x0000
+#define OMAP2420_PRCM_REVISION OMAP2420_PRM_REGADDR(OCP_MOD, 0x0000)
+#define OMAP2_PRCM_SYSCONFIG_OFFSET 0x0010
+#define OMAP2420_PRCM_SYSCONFIG OMAP2420_PRM_REGADDR(OCP_MOD, 0x0010)
+
+#define OMAP2_PRCM_IRQSTATUS_MPU_OFFSET 0x0018
+#define OMAP2420_PRCM_IRQSTATUS_MPU OMAP2420_PRM_REGADDR(OCP_MOD, 0x0018)
+#define OMAP2_PRCM_IRQENABLE_MPU_OFFSET 0x001c
+#define OMAP2420_PRCM_IRQENABLE_MPU OMAP2420_PRM_REGADDR(OCP_MOD, 0x001c)
+
+#define OMAP2_PRCM_VOLTCTRL_OFFSET 0x0050
+#define OMAP2420_PRCM_VOLTCTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0050)
+#define OMAP2_PRCM_VOLTST_OFFSET 0x0054
+#define OMAP2420_PRCM_VOLTST OMAP2420_PRM_REGADDR(OCP_MOD, 0x0054)
+#define OMAP2_PRCM_CLKSRC_CTRL_OFFSET 0x0060
+#define OMAP2420_PRCM_CLKSRC_CTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0060)
+#define OMAP2_PRCM_CLKOUT_CTRL_OFFSET 0x0070
+#define OMAP2420_PRCM_CLKOUT_CTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0070)
+#define OMAP2_PRCM_CLKEMUL_CTRL_OFFSET 0x0078
+#define OMAP2420_PRCM_CLKEMUL_CTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0078)
+#define OMAP2_PRCM_CLKCFG_CTRL_OFFSET 0x0080
+#define OMAP2420_PRCM_CLKCFG_CTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0080)
+#define OMAP2_PRCM_CLKCFG_STATUS_OFFSET 0x0084
+#define OMAP2420_PRCM_CLKCFG_STATUS OMAP2420_PRM_REGADDR(OCP_MOD, 0x0084)
+#define OMAP2_PRCM_VOLTSETUP_OFFSET 0x0090
+#define OMAP2420_PRCM_VOLTSETUP OMAP2420_PRM_REGADDR(OCP_MOD, 0x0090)
+#define OMAP2_PRCM_CLKSSETUP_OFFSET 0x0094
+#define OMAP2420_PRCM_CLKSSETUP OMAP2420_PRM_REGADDR(OCP_MOD, 0x0094)
+#define OMAP2_PRCM_POLCTRL_OFFSET 0x0098
+#define OMAP2420_PRCM_POLCTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0098)
+
+#define OMAP2430_PRCM_REVISION OMAP2430_PRM_REGADDR(OCP_MOD, 0x0000)
+#define OMAP2430_PRCM_SYSCONFIG OMAP2430_PRM_REGADDR(OCP_MOD, 0x0010)
+
+#define OMAP2430_PRCM_IRQSTATUS_MPU OMAP2430_PRM_REGADDR(OCP_MOD, 0x0018)
+#define OMAP2430_PRCM_IRQENABLE_MPU OMAP2430_PRM_REGADDR(OCP_MOD, 0x001c)
+
+#define OMAP2430_PRCM_VOLTCTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0050)
+#define OMAP2430_PRCM_VOLTST OMAP2430_PRM_REGADDR(OCP_MOD, 0x0054)
+#define OMAP2430_PRCM_CLKSRC_CTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0060)
+#define OMAP2430_PRCM_CLKOUT_CTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0070)
+#define OMAP2430_PRCM_CLKEMUL_CTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0078)
+#define OMAP2430_PRCM_CLKCFG_CTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0080)
+#define OMAP2430_PRCM_CLKCFG_STATUS OMAP2430_PRM_REGADDR(OCP_MOD, 0x0084)
+#define OMAP2430_PRCM_VOLTSETUP OMAP2430_PRM_REGADDR(OCP_MOD, 0x0090)
+#define OMAP2430_PRCM_CLKSSETUP OMAP2430_PRM_REGADDR(OCP_MOD, 0x0094)
+#define OMAP2430_PRCM_POLCTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0098)
+
+/*
+ * Module specific PRM register offsets from PRM_BASE + domain offset
+ *
+ * Use prm_{read,write}_mod_reg() with these registers.
+ *
+ * With a few exceptions, these are the register names beginning with
+ * {PM,RM}_* on both OMAP2/3 SoC families.. (The exceptions are the
+ * IRQSTATUS and IRQENABLE bits.)
+ */
+
+/* Register offsets appearing on both OMAP2 and OMAP3 */
+
+#define OMAP2_RM_RSTCTRL 0x0050
+#define OMAP2_RM_RSTTIME 0x0054
+#define OMAP2_RM_RSTST 0x0058
+#define OMAP2_PM_PWSTCTRL 0x00e0
+#define OMAP2_PM_PWSTST 0x00e4
+
+#define PM_WKEN 0x00a0
+#define PM_WKEN1 PM_WKEN
+#define PM_WKST 0x00b0
+#define PM_WKST1 PM_WKST
+#define PM_WKDEP 0x00c8
+#define PM_EVGENCTRL 0x00d4
+#define PM_EVGENONTIM 0x00d8
+#define PM_EVGENOFFTIM 0x00dc
+
+/* OMAP2xxx specific register offsets */
+#define OMAP24XX_PM_WKEN2 0x00a4
+#define OMAP24XX_PM_WKST2 0x00b4
+
+#define OMAP24XX_PRCM_IRQSTATUS_DSP 0x00f0 /* IVA mod */
+#define OMAP24XX_PRCM_IRQENABLE_DSP 0x00f4 /* IVA mod */
+#define OMAP24XX_PRCM_IRQSTATUS_IVA 0x00f8
+#define OMAP24XX_PRCM_IRQENABLE_IVA 0x00fc
+
+#endif
diff --git a/arch/arm/mach-omap2/prm2xxx_3xxx.c b/arch/arm/mach-omap2/prm2xxx_3xxx.c
index 9529984..0d6cc54 100644
--- a/arch/arm/mach-omap2/prm2xxx_3xxx.c
+++ b/arch/arm/mach-omap2/prm2xxx_3xxx.c
@@ -15,82 +15,11 @@
#include <linux/errno.h>
#include <linux/err.h>
#include <linux/io.h>
-#include <linux/irq.h>
-#include <plat/prcm.h>
-
-#include "soc.h"
#include "common.h"
-#include "vp.h"
#include "prm2xxx_3xxx.h"
-#include "cm2xxx_3xxx.h"
#include "prm-regbits-24xx.h"
-#include "prm-regbits-34xx.h"
-
-static const struct omap_prcm_irq omap3_prcm_irqs[] = {
- OMAP_PRCM_IRQ("wkup", 0, 0),
- OMAP_PRCM_IRQ("io", 9, 1),
-};
-
-static struct omap_prcm_irq_setup omap3_prcm_irq_setup = {
- .ack = OMAP3_PRM_IRQSTATUS_MPU_OFFSET,
- .mask = OMAP3_PRM_IRQENABLE_MPU_OFFSET,
- .nr_regs = 1,
- .irqs = omap3_prcm_irqs,
- .nr_irqs = ARRAY_SIZE(omap3_prcm_irqs),
- .irq = 11 + OMAP_INTC_START,
- .read_pending_irqs = &omap3xxx_prm_read_pending_irqs,
- .ocp_barrier = &omap3xxx_prm_ocp_barrier,
- .save_and_clear_irqen = &omap3xxx_prm_save_and_clear_irqen,
- .restore_irqen = &omap3xxx_prm_restore_irqen,
-};
-
-u32 omap2_prm_read_mod_reg(s16 module, u16 idx)
-{
- return __raw_readl(prm_base + module + idx);
-}
-
-void omap2_prm_write_mod_reg(u32 val, s16 module, u16 idx)
-{
- __raw_writel(val, prm_base + module + idx);
-}
-
-/* Read-modify-write a register in a PRM module. Caller must lock */
-u32 omap2_prm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx)
-{
- u32 v;
-
- v = omap2_prm_read_mod_reg(module, idx);
- v &= ~mask;
- v |= bits;
- omap2_prm_write_mod_reg(v, module, idx);
-
- return v;
-}
-
-/* Read a PRM register, AND it, and shift the result down to bit 0 */
-u32 omap2_prm_read_mod_bits_shift(s16 domain, s16 idx, u32 mask)
-{
- u32 v;
-
- v = omap2_prm_read_mod_reg(domain, idx);
- v &= mask;
- v >>= __ffs(mask);
-
- return v;
-}
-
-u32 omap2_prm_set_mod_reg_bits(u32 bits, s16 module, s16 idx)
-{
- return omap2_prm_rmw_mod_reg_bits(bits, bits, module, idx);
-}
-
-u32 omap2_prm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx)
-{
- return omap2_prm_rmw_mod_reg_bits(bits, 0x0, module, idx);
-}
-
/**
* omap2_prm_is_hardreset_asserted - read the HW reset line state of
@@ -104,9 +33,6 @@ u32 omap2_prm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx)
*/
int omap2_prm_is_hardreset_asserted(s16 prm_mod, u8 shift)
{
- if (!(cpu_is_omap24xx() || cpu_is_omap34xx()))
- return -EINVAL;
-
return omap2_prm_read_mod_bits_shift(prm_mod, OMAP2_RM_RSTCTRL,
(1 << shift));
}
@@ -127,9 +53,6 @@ int omap2_prm_assert_hardreset(s16 prm_mod, u8 shift)
{
u32 mask;
- if (!(cpu_is_omap24xx() || cpu_is_omap34xx()))
- return -EINVAL;
-
mask = 1 << shift;
omap2_prm_rmw_mod_reg_bits(mask, mask, prm_mod, OMAP2_RM_RSTCTRL);
@@ -156,9 +79,6 @@ int omap2_prm_deassert_hardreset(s16 prm_mod, u8 rst_shift, u8 st_shift)
u32 rst, st;
int c;
- if (!(cpu_is_omap24xx() || cpu_is_omap34xx()))
- return -EINVAL;
-
rst = 1 << rst_shift;
st = 1 << st_shift;
@@ -178,188 +98,3 @@ int omap2_prm_deassert_hardreset(s16 prm_mod, u8 rst_shift, u8 st_shift)
return (c == MAX_MODULE_HARDRESET_WAIT) ? -EBUSY : 0;
}
-/* PRM VP */
-
-/*
- * struct omap3_vp - OMAP3 VP register access description.
- * @tranxdone_status: VP_TRANXDONE_ST bitmask in PRM_IRQSTATUS_MPU reg
- */
-struct omap3_vp {
- u32 tranxdone_status;
-};
-
-static struct omap3_vp omap3_vp[] = {
- [OMAP3_VP_VDD_MPU_ID] = {
- .tranxdone_status = OMAP3430_VP1_TRANXDONE_ST_MASK,
- },
- [OMAP3_VP_VDD_CORE_ID] = {
- .tranxdone_status = OMAP3430_VP2_TRANXDONE_ST_MASK,
- },
-};
-
-#define MAX_VP_ID ARRAY_SIZE(omap3_vp);
-
-u32 omap3_prm_vp_check_txdone(u8 vp_id)
-{
- struct omap3_vp *vp = &omap3_vp[vp_id];
- u32 irqstatus;
-
- irqstatus = omap2_prm_read_mod_reg(OCP_MOD,
- OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
- return irqstatus & vp->tranxdone_status;
-}
-
-void omap3_prm_vp_clear_txdone(u8 vp_id)
-{
- struct omap3_vp *vp = &omap3_vp[vp_id];
-
- omap2_prm_write_mod_reg(vp->tranxdone_status,
- OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
-}
-
-u32 omap3_prm_vcvp_read(u8 offset)
-{
- return omap2_prm_read_mod_reg(OMAP3430_GR_MOD, offset);
-}
-
-void omap3_prm_vcvp_write(u32 val, u8 offset)
-{
- omap2_prm_write_mod_reg(val, OMAP3430_GR_MOD, offset);
-}
-
-u32 omap3_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset)
-{
- return omap2_prm_rmw_mod_reg_bits(mask, bits, OMAP3430_GR_MOD, offset);
-}
-
-/**
- * omap3xxx_prm_read_pending_irqs - read pending PRM MPU IRQs into @events
- * @events: ptr to a u32, preallocated by caller
- *
- * Read PRM_IRQSTATUS_MPU bits, AND'ed with the currently-enabled PRM
- * MPU IRQs, and store the result into the u32 pointed to by @events.
- * No return value.
- */
-void omap3xxx_prm_read_pending_irqs(unsigned long *events)
-{
- u32 mask, st;
-
- /* XXX Can the mask read be avoided (e.g., can it come from RAM?) */
- mask = omap2_prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET);
- st = omap2_prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
-
- events[0] = mask & st;
-}
-
-/**
- * omap3xxx_prm_ocp_barrier - force buffered MPU writes to the PRM to complete
- *
- * Force any buffered writes to the PRM IP block to complete. Needed
- * by the PRM IRQ handler, which reads and writes directly to the IP
- * block, to avoid race conditions after acknowledging or clearing IRQ
- * bits. No return value.
- */
-void omap3xxx_prm_ocp_barrier(void)
-{
- omap2_prm_read_mod_reg(OCP_MOD, OMAP3_PRM_REVISION_OFFSET);
-}
-
-/**
- * omap3xxx_prm_save_and_clear_irqen - save/clear PRM_IRQENABLE_MPU reg
- * @saved_mask: ptr to a u32 array to save IRQENABLE bits
- *
- * Save the PRM_IRQENABLE_MPU register to @saved_mask. @saved_mask
- * must be allocated by the caller. Intended to be used in the PRM
- * interrupt handler suspend callback. The OCP barrier is needed to
- * ensure the write to disable PRM interrupts reaches the PRM before
- * returning; otherwise, spurious interrupts might occur. No return
- * value.
- */
-void omap3xxx_prm_save_and_clear_irqen(u32 *saved_mask)
-{
- saved_mask[0] = omap2_prm_read_mod_reg(OCP_MOD,
- OMAP3_PRM_IRQENABLE_MPU_OFFSET);
- omap2_prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQENABLE_MPU_OFFSET);
-
- /* OCP barrier */
- omap2_prm_read_mod_reg(OCP_MOD, OMAP3_PRM_REVISION_OFFSET);
-}
-
-/**
- * omap3xxx_prm_restore_irqen - set PRM_IRQENABLE_MPU register from args
- * @saved_mask: ptr to a u32 array of IRQENABLE bits saved previously
- *
- * Restore the PRM_IRQENABLE_MPU register from @saved_mask. Intended
- * to be used in the PRM interrupt handler resume callback to restore
- * values saved by omap3xxx_prm_save_and_clear_irqen(). No OCP
- * barrier should be needed here; any pending PRM interrupts will fire
- * once the writes reach the PRM. No return value.
- */
-void omap3xxx_prm_restore_irqen(u32 *saved_mask)
-{
- omap2_prm_write_mod_reg(saved_mask[0], OCP_MOD,
- OMAP3_PRM_IRQENABLE_MPU_OFFSET);
-}
-
-/**
- * omap3xxx_prm_reconfigure_io_chain - clear latches and reconfigure I/O chain
- *
- * Clear any previously-latched I/O wakeup events and ensure that the
- * I/O wakeup gates are aligned with the current mux settings. Works
- * by asserting WUCLKIN, waiting for WUCLKOUT to be asserted, and then
- * deasserting WUCLKIN and clearing the ST_IO_CHAIN WKST bit. No
- * return value.
- */
-void omap3xxx_prm_reconfigure_io_chain(void)
-{
- int i = 0;
-
- omap2_prm_set_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD,
- PM_WKEN);
-
- omap_test_timeout(omap2_prm_read_mod_reg(WKUP_MOD, PM_WKST) &
- OMAP3430_ST_IO_CHAIN_MASK,
- MAX_IOPAD_LATCH_TIME, i);
- if (i == MAX_IOPAD_LATCH_TIME)
- pr_warn("PRM: I/O chain clock line assertion timed out\n");
-
- omap2_prm_clear_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD,
- PM_WKEN);
-
- omap2_prm_set_mod_reg_bits(OMAP3430_ST_IO_CHAIN_MASK, WKUP_MOD,
- PM_WKST);
-
- omap2_prm_read_mod_reg(WKUP_MOD, PM_WKST);
-}
-
-/**
- * omap3xxx_prm_enable_io_wakeup - enable wakeup events from I/O wakeup latches
- *
- * Activates the I/O wakeup event latches and allows events logged by
- * those latches to signal a wakeup event to the PRCM. For I/O
- * wakeups to occur, WAKEUPENABLE bits must be set in the pad mux
- * registers, and omap3xxx_prm_reconfigure_io_chain() must be called.
- * No return value.
- */
-static void __init omap3xxx_prm_enable_io_wakeup(void)
-{
- if (omap3_has_io_wakeup())
- omap2_prm_set_mod_reg_bits(OMAP3430_EN_IO_MASK, WKUP_MOD,
- PM_WKEN);
-}
-
-static int __init omap3xxx_prcm_init(void)
-{
- int ret = 0;
-
- if (cpu_is_omap34xx()) {
- omap3xxx_prm_enable_io_wakeup();
- ret = omap_prcm_register_chain_handler(&omap3_prcm_irq_setup);
- if (!ret)
- irq_set_status_flags(omap_prcm_event_to_irq("io"),
- IRQ_NOAUTOEN);
- }
-
- return ret;
-}
-subsys_initcall(omap3xxx_prcm_init);
diff --git a/arch/arm/mach-omap2/prm2xxx_3xxx.h b/arch/arm/mach-omap2/prm2xxx_3xxx.h
index c19d249..8d09a1a 100644
--- a/arch/arm/mach-omap2/prm2xxx_3xxx.h
+++ b/arch/arm/mach-omap2/prm2xxx_3xxx.h
@@ -1,7 +1,7 @@
/*
- * OMAP2/3 Power/Reset Management (PRM) register definitions
+ * OMAP2xxx/3xxx-common Power/Reset Management (PRM) register definitions
*
- * Copyright (C) 2007-2009, 2011 Texas Instruments, Inc.
+ * Copyright (C) 2007-2009, 2011-2012 Texas Instruments, Inc.
* Copyright (C) 2008-2010 Nokia Corporation
* Paul Walmsley
*
@@ -19,160 +19,6 @@
#include "prcm-common.h"
#include "prm.h"
-#define OMAP2420_PRM_REGADDR(module, reg) \
- OMAP2_L4_IO_ADDRESS(OMAP2420_PRM_BASE + (module) + (reg))
-#define OMAP2430_PRM_REGADDR(module, reg) \
- OMAP2_L4_IO_ADDRESS(OMAP2430_PRM_BASE + (module) + (reg))
-#define OMAP34XX_PRM_REGADDR(module, reg) \
- OMAP2_L4_IO_ADDRESS(OMAP3430_PRM_BASE + (module) + (reg))
-
-
-/*
- * OMAP2-specific global PRM registers
- * Use __raw_{read,write}l() with these registers.
- *
- * With a few exceptions, these are the register names beginning with
- * PRCM_* on 24xx. (The exceptions are the IRQSTATUS and IRQENABLE
- * bits.)
- *
- */
-
-#define OMAP2_PRCM_REVISION_OFFSET 0x0000
-#define OMAP2420_PRCM_REVISION OMAP2420_PRM_REGADDR(OCP_MOD, 0x0000)
-#define OMAP2_PRCM_SYSCONFIG_OFFSET 0x0010
-#define OMAP2420_PRCM_SYSCONFIG OMAP2420_PRM_REGADDR(OCP_MOD, 0x0010)
-
-#define OMAP2_PRCM_IRQSTATUS_MPU_OFFSET 0x0018
-#define OMAP2420_PRCM_IRQSTATUS_MPU OMAP2420_PRM_REGADDR(OCP_MOD, 0x0018)
-#define OMAP2_PRCM_IRQENABLE_MPU_OFFSET 0x001c
-#define OMAP2420_PRCM_IRQENABLE_MPU OMAP2420_PRM_REGADDR(OCP_MOD, 0x001c)
-
-#define OMAP2_PRCM_VOLTCTRL_OFFSET 0x0050
-#define OMAP2420_PRCM_VOLTCTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0050)
-#define OMAP2_PRCM_VOLTST_OFFSET 0x0054
-#define OMAP2420_PRCM_VOLTST OMAP2420_PRM_REGADDR(OCP_MOD, 0x0054)
-#define OMAP2_PRCM_CLKSRC_CTRL_OFFSET 0x0060
-#define OMAP2420_PRCM_CLKSRC_CTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0060)
-#define OMAP2_PRCM_CLKOUT_CTRL_OFFSET 0x0070
-#define OMAP2420_PRCM_CLKOUT_CTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0070)
-#define OMAP2_PRCM_CLKEMUL_CTRL_OFFSET 0x0078
-#define OMAP2420_PRCM_CLKEMUL_CTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0078)
-#define OMAP2_PRCM_CLKCFG_CTRL_OFFSET 0x0080
-#define OMAP2420_PRCM_CLKCFG_CTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0080)
-#define OMAP2_PRCM_CLKCFG_STATUS_OFFSET 0x0084
-#define OMAP2420_PRCM_CLKCFG_STATUS OMAP2420_PRM_REGADDR(OCP_MOD, 0x0084)
-#define OMAP2_PRCM_VOLTSETUP_OFFSET 0x0090
-#define OMAP2420_PRCM_VOLTSETUP OMAP2420_PRM_REGADDR(OCP_MOD, 0x0090)
-#define OMAP2_PRCM_CLKSSETUP_OFFSET 0x0094
-#define OMAP2420_PRCM_CLKSSETUP OMAP2420_PRM_REGADDR(OCP_MOD, 0x0094)
-#define OMAP2_PRCM_POLCTRL_OFFSET 0x0098
-#define OMAP2420_PRCM_POLCTRL OMAP2420_PRM_REGADDR(OCP_MOD, 0x0098)
-
-#define OMAP2430_PRCM_REVISION OMAP2430_PRM_REGADDR(OCP_MOD, 0x0000)
-#define OMAP2430_PRCM_SYSCONFIG OMAP2430_PRM_REGADDR(OCP_MOD, 0x0010)
-
-#define OMAP2430_PRCM_IRQSTATUS_MPU OMAP2430_PRM_REGADDR(OCP_MOD, 0x0018)
-#define OMAP2430_PRCM_IRQENABLE_MPU OMAP2430_PRM_REGADDR(OCP_MOD, 0x001c)
-
-#define OMAP2430_PRCM_VOLTCTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0050)
-#define OMAP2430_PRCM_VOLTST OMAP2430_PRM_REGADDR(OCP_MOD, 0x0054)
-#define OMAP2430_PRCM_CLKSRC_CTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0060)
-#define OMAP2430_PRCM_CLKOUT_CTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0070)
-#define OMAP2430_PRCM_CLKEMUL_CTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0078)
-#define OMAP2430_PRCM_CLKCFG_CTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0080)
-#define OMAP2430_PRCM_CLKCFG_STATUS OMAP2430_PRM_REGADDR(OCP_MOD, 0x0084)
-#define OMAP2430_PRCM_VOLTSETUP OMAP2430_PRM_REGADDR(OCP_MOD, 0x0090)
-#define OMAP2430_PRCM_CLKSSETUP OMAP2430_PRM_REGADDR(OCP_MOD, 0x0094)
-#define OMAP2430_PRCM_POLCTRL OMAP2430_PRM_REGADDR(OCP_MOD, 0x0098)
-
-/*
- * OMAP3-specific global PRM registers
- * Use __raw_{read,write}l() with these registers.
- *
- * With a few exceptions, these are the register names beginning with
- * PRM_* on 34xx. (The exceptions are the IRQSTATUS and IRQENABLE
- * bits.)
- */
-
-#define OMAP3_PRM_REVISION_OFFSET 0x0004
-#define OMAP3430_PRM_REVISION OMAP34XX_PRM_REGADDR(OCP_MOD, 0x0004)
-#define OMAP3_PRM_SYSCONFIG_OFFSET 0x0014
-#define OMAP3430_PRM_SYSCONFIG OMAP34XX_PRM_REGADDR(OCP_MOD, 0x0014)
-
-#define OMAP3_PRM_IRQSTATUS_MPU_OFFSET 0x0018
-#define OMAP3430_PRM_IRQSTATUS_MPU OMAP34XX_PRM_REGADDR(OCP_MOD, 0x0018)
-#define OMAP3_PRM_IRQENABLE_MPU_OFFSET 0x001c
-#define OMAP3430_PRM_IRQENABLE_MPU OMAP34XX_PRM_REGADDR(OCP_MOD, 0x001c)
-
-
-#define OMAP3_PRM_VC_SMPS_SA_OFFSET 0x0020
-#define OMAP3430_PRM_VC_SMPS_SA OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0020)
-#define OMAP3_PRM_VC_SMPS_VOL_RA_OFFSET 0x0024
-#define OMAP3430_PRM_VC_SMPS_VOL_RA OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0024)
-#define OMAP3_PRM_VC_SMPS_CMD_RA_OFFSET 0x0028
-#define OMAP3430_PRM_VC_SMPS_CMD_RA OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0028)
-#define OMAP3_PRM_VC_CMD_VAL_0_OFFSET 0x002c
-#define OMAP3430_PRM_VC_CMD_VAL_0 OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x002c)
-#define OMAP3_PRM_VC_CMD_VAL_1_OFFSET 0x0030
-#define OMAP3430_PRM_VC_CMD_VAL_1 OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0030)
-#define OMAP3_PRM_VC_CH_CONF_OFFSET 0x0034
-#define OMAP3430_PRM_VC_CH_CONF OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0034)
-#define OMAP3_PRM_VC_I2C_CFG_OFFSET 0x0038
-#define OMAP3430_PRM_VC_I2C_CFG OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0038)
-#define OMAP3_PRM_VC_BYPASS_VAL_OFFSET 0x003c
-#define OMAP3430_PRM_VC_BYPASS_VAL OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x003c)
-#define OMAP3_PRM_RSTCTRL_OFFSET 0x0050
-#define OMAP3430_PRM_RSTCTRL OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0050)
-#define OMAP3_PRM_RSTTIME_OFFSET 0x0054
-#define OMAP3430_PRM_RSTTIME OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0054)
-#define OMAP3_PRM_RSTST_OFFSET 0x0058
-#define OMAP3430_PRM_RSTST OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0058)
-#define OMAP3_PRM_VOLTCTRL_OFFSET 0x0060
-#define OMAP3430_PRM_VOLTCTRL OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0060)
-#define OMAP3_PRM_SRAM_PCHARGE_OFFSET 0x0064
-#define OMAP3430_PRM_SRAM_PCHARGE OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0064)
-#define OMAP3_PRM_CLKSRC_CTRL_OFFSET 0x0070
-#define OMAP3430_PRM_CLKSRC_CTRL OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0070)
-#define OMAP3_PRM_VOLTSETUP1_OFFSET 0x0090
-#define OMAP3430_PRM_VOLTSETUP1 OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0090)
-#define OMAP3_PRM_VOLTOFFSET_OFFSET 0x0094
-#define OMAP3430_PRM_VOLTOFFSET OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0094)
-#define OMAP3_PRM_CLKSETUP_OFFSET 0x0098
-#define OMAP3430_PRM_CLKSETUP OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0098)
-#define OMAP3_PRM_POLCTRL_OFFSET 0x009c
-#define OMAP3430_PRM_POLCTRL OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x009c)
-#define OMAP3_PRM_VOLTSETUP2_OFFSET 0x00a0
-#define OMAP3430_PRM_VOLTSETUP2 OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00a0)
-#define OMAP3_PRM_VP1_CONFIG_OFFSET 0x00b0
-#define OMAP3430_PRM_VP1_CONFIG OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00b0)
-#define OMAP3_PRM_VP1_VSTEPMIN_OFFSET 0x00b4
-#define OMAP3430_PRM_VP1_VSTEPMIN OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00b4)
-#define OMAP3_PRM_VP1_VSTEPMAX_OFFSET 0x00b8
-#define OMAP3430_PRM_VP1_VSTEPMAX OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00b8)
-#define OMAP3_PRM_VP1_VLIMITTO_OFFSET 0x00bc
-#define OMAP3430_PRM_VP1_VLIMITTO OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00bc)
-#define OMAP3_PRM_VP1_VOLTAGE_OFFSET 0x00c0
-#define OMAP3430_PRM_VP1_VOLTAGE OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00c0)
-#define OMAP3_PRM_VP1_STATUS_OFFSET 0x00c4
-#define OMAP3430_PRM_VP1_STATUS OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00c4)
-#define OMAP3_PRM_VP2_CONFIG_OFFSET 0x00d0
-#define OMAP3430_PRM_VP2_CONFIG OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00d0)
-#define OMAP3_PRM_VP2_VSTEPMIN_OFFSET 0x00d4
-#define OMAP3430_PRM_VP2_VSTEPMIN OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00d4)
-#define OMAP3_PRM_VP2_VSTEPMAX_OFFSET 0x00d8
-#define OMAP3430_PRM_VP2_VSTEPMAX OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00d8)
-#define OMAP3_PRM_VP2_VLIMITTO_OFFSET 0x00dc
-#define OMAP3430_PRM_VP2_VLIMITTO OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00dc)
-#define OMAP3_PRM_VP2_VOLTAGE_OFFSET 0x00e0
-#define OMAP3430_PRM_VP2_VOLTAGE OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00e0)
-#define OMAP3_PRM_VP2_STATUS_OFFSET 0x00e4
-#define OMAP3430_PRM_VP2_STATUS OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00e4)
-
-#define OMAP3_PRM_CLKSEL_OFFSET 0x0040
-#define OMAP3430_PRM_CLKSEL OMAP34XX_PRM_REGADDR(OMAP3430_CCR_MOD, 0x0040)
-#define OMAP3_PRM_CLKOUT_CTRL_OFFSET 0x0070
-#define OMAP3430_PRM_CLKOUT_CTRL OMAP34XX_PRM_REGADDR(OMAP3430_CCR_MOD, 0x0070)
-
/*
* Module specific PRM register offsets from PRM_BASE + domain offset
*
@@ -200,67 +46,63 @@
#define PM_EVGENONTIM 0x00d8
#define PM_EVGENOFFTIM 0x00dc
-/* OMAP2xxx specific register offsets */
-#define OMAP24XX_PM_WKEN2 0x00a4
-#define OMAP24XX_PM_WKST2 0x00b4
-
-#define OMAP24XX_PRCM_IRQSTATUS_DSP 0x00f0 /* IVA mod */
-#define OMAP24XX_PRCM_IRQENABLE_DSP 0x00f4 /* IVA mod */
-#define OMAP24XX_PRCM_IRQSTATUS_IVA 0x00f8
-#define OMAP24XX_PRCM_IRQENABLE_IVA 0x00fc
-
-/* OMAP3 specific register offsets */
-#define OMAP3430ES2_PM_WKEN3 0x00f0
-#define OMAP3430ES2_PM_WKST3 0x00b8
-
-#define OMAP3430_PM_MPUGRPSEL 0x00a4
-#define OMAP3430_PM_MPUGRPSEL1 OMAP3430_PM_MPUGRPSEL
-#define OMAP3430ES2_PM_MPUGRPSEL3 0x00f8
-#define OMAP3430_PM_IVAGRPSEL 0x00a8
-#define OMAP3430_PM_IVAGRPSEL1 OMAP3430_PM_IVAGRPSEL
-#define OMAP3430ES2_PM_IVAGRPSEL3 0x00f4
-
-#define OMAP3430_PM_PREPWSTST 0x00e8
-
-#define OMAP3430_PRM_IRQSTATUS_IVA2 0x00f8
-#define OMAP3430_PRM_IRQENABLE_IVA2 0x00fc
+#ifndef __ASSEMBLER__
+#include <linux/io.h>
-#ifndef __ASSEMBLER__
/* Power/reset management domain register get/set */
-extern u32 omap2_prm_read_mod_reg(s16 module, u16 idx);
-extern void omap2_prm_write_mod_reg(u32 val, s16 module, u16 idx);
-extern u32 omap2_prm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx);
-extern u32 omap2_prm_set_mod_reg_bits(u32 bits, s16 module, s16 idx);
-extern u32 omap2_prm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx);
-extern u32 omap2_prm_read_mod_bits_shift(s16 domain, s16 idx, u32 mask);
+static inline u32 omap2_prm_read_mod_reg(s16 module, u16 idx)
+{
+ return __raw_readl(prm_base + module + idx);
+}
+
+static inline void omap2_prm_write_mod_reg(u32 val, s16 module, u16 idx)
+{
+ __raw_writel(val, prm_base + module + idx);
+}
+
+/* Read-modify-write a register in a PRM module. Caller must lock */
+static inline u32 omap2_prm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module,
+ s16 idx)
+{
+ u32 v;
+
+ v = omap2_prm_read_mod_reg(module, idx);
+ v &= ~mask;
+ v |= bits;
+ omap2_prm_write_mod_reg(v, module, idx);
+
+ return v;
+}
+
+/* Read a PRM register, AND it, and shift the result down to bit 0 */
+static inline u32 omap2_prm_read_mod_bits_shift(s16 domain, s16 idx, u32 mask)
+{
+ u32 v;
+
+ v = omap2_prm_read_mod_reg(domain, idx);
+ v &= mask;
+ v >>= __ffs(mask);
+
+ return v;
+}
+
+static inline u32 omap2_prm_set_mod_reg_bits(u32 bits, s16 module, s16 idx)
+{
+ return omap2_prm_rmw_mod_reg_bits(bits, bits, module, idx);
+}
+
+static inline u32 omap2_prm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx)
+{
+ return omap2_prm_rmw_mod_reg_bits(bits, 0x0, module, idx);
+}
/* These omap2_ PRM functions apply to both OMAP2 and 3 */
extern int omap2_prm_is_hardreset_asserted(s16 prm_mod, u8 shift);
extern int omap2_prm_assert_hardreset(s16 prm_mod, u8 shift);
extern int omap2_prm_deassert_hardreset(s16 prm_mod, u8 rst_shift, u8 st_shift);
-/* OMAP3-specific VP functions */
-u32 omap3_prm_vp_check_txdone(u8 vp_id);
-void omap3_prm_vp_clear_txdone(u8 vp_id);
-
-/*
- * OMAP3 access functions for voltage controller (VC) and
- * voltage proccessor (VP) in the PRM.
- */
-extern u32 omap3_prm_vcvp_read(u8 offset);
-extern void omap3_prm_vcvp_write(u32 val, u8 offset);
-extern u32 omap3_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
-
-extern void omap3xxx_prm_reconfigure_io_chain(void);
-
-/* PRM interrupt-related functions */
-extern void omap3xxx_prm_read_pending_irqs(unsigned long *events);
-extern void omap3xxx_prm_ocp_barrier(void);
-extern void omap3xxx_prm_save_and_clear_irqen(u32 *saved_mask);
-extern void omap3xxx_prm_restore_irqen(u32 *saved_mask);
-
#endif /* __ASSEMBLER */
/*
diff --git a/arch/arm/mach-omap2/prm2xxx_3xxx.c b/arch/arm/mach-omap2/prm3xxx.c
similarity index 57%
copy from arch/arm/mach-omap2/prm2xxx_3xxx.c
copy to arch/arm/mach-omap2/prm3xxx.c
index 9529984..88f7d8d 100644
--- a/arch/arm/mach-omap2/prm2xxx_3xxx.c
+++ b/arch/arm/mach-omap2/prm3xxx.c
@@ -1,7 +1,7 @@
/*
- * OMAP2/3 PRM module functions
+ * OMAP3xxx PRM module functions
*
- * Copyright (C) 2010-2011 Texas Instruments, Inc.
+ * Copyright (C) 2010-2012 Texas Instruments, Inc.
* Copyright (C) 2010 Nokia Corporation
* Benoît Cousson
* Paul Walmsley
@@ -17,15 +17,14 @@
#include <linux/io.h>
#include <linux/irq.h>
+#include "common.h"
+#include <plat/cpu.h>
#include <plat/prcm.h>
-#include "soc.h"
-#include "common.h"
#include "vp.h"
-#include "prm2xxx_3xxx.h"
+#include "prm3xxx.h"
#include "cm2xxx_3xxx.h"
-#include "prm-regbits-24xx.h"
#include "prm-regbits-34xx.h"
static const struct omap_prcm_irq omap3_prcm_irqs[] = {
@@ -46,138 +45,6 @@ static struct omap_prcm_irq_setup omap3_prcm_irq_setup = {
.restore_irqen = &omap3xxx_prm_restore_irqen,
};
-u32 omap2_prm_read_mod_reg(s16 module, u16 idx)
-{
- return __raw_readl(prm_base + module + idx);
-}
-
-void omap2_prm_write_mod_reg(u32 val, s16 module, u16 idx)
-{
- __raw_writel(val, prm_base + module + idx);
-}
-
-/* Read-modify-write a register in a PRM module. Caller must lock */
-u32 omap2_prm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx)
-{
- u32 v;
-
- v = omap2_prm_read_mod_reg(module, idx);
- v &= ~mask;
- v |= bits;
- omap2_prm_write_mod_reg(v, module, idx);
-
- return v;
-}
-
-/* Read a PRM register, AND it, and shift the result down to bit 0 */
-u32 omap2_prm_read_mod_bits_shift(s16 domain, s16 idx, u32 mask)
-{
- u32 v;
-
- v = omap2_prm_read_mod_reg(domain, idx);
- v &= mask;
- v >>= __ffs(mask);
-
- return v;
-}
-
-u32 omap2_prm_set_mod_reg_bits(u32 bits, s16 module, s16 idx)
-{
- return omap2_prm_rmw_mod_reg_bits(bits, bits, module, idx);
-}
-
-u32 omap2_prm_clear_mod_reg_bits(u32 bits, s16 module, s16 idx)
-{
- return omap2_prm_rmw_mod_reg_bits(bits, 0x0, module, idx);
-}
-
-
-/**
- * omap2_prm_is_hardreset_asserted - read the HW reset line state of
- * submodules contained in the hwmod module
- * @prm_mod: PRM submodule base (e.g. CORE_MOD)
- * @shift: register bit shift corresponding to the reset line to check
- *
- * Returns 1 if the (sub)module hardreset line is currently asserted,
- * 0 if the (sub)module hardreset line is not currently asserted, or
- * -EINVAL if called while running on a non-OMAP2/3 chip.
- */
-int omap2_prm_is_hardreset_asserted(s16 prm_mod, u8 shift)
-{
- if (!(cpu_is_omap24xx() || cpu_is_omap34xx()))
- return -EINVAL;
-
- return omap2_prm_read_mod_bits_shift(prm_mod, OMAP2_RM_RSTCTRL,
- (1 << shift));
-}
-
-/**
- * omap2_prm_assert_hardreset - assert the HW reset line of a submodule
- * @prm_mod: PRM submodule base (e.g. CORE_MOD)
- * @shift: register bit shift corresponding to the reset line to assert
- *
- * Some IPs like dsp or iva contain processors that require an HW
- * reset line to be asserted / deasserted in order to fully enable the
- * IP. These modules may have multiple hard-reset lines that reset
- * different 'submodules' inside the IP block. This function will
- * place the submodule into reset. Returns 0 upon success or -EINVAL
- * upon an argument error.
- */
-int omap2_prm_assert_hardreset(s16 prm_mod, u8 shift)
-{
- u32 mask;
-
- if (!(cpu_is_omap24xx() || cpu_is_omap34xx()))
- return -EINVAL;
-
- mask = 1 << shift;
- omap2_prm_rmw_mod_reg_bits(mask, mask, prm_mod, OMAP2_RM_RSTCTRL);
-
- return 0;
-}
-
-/**
- * omap2_prm_deassert_hardreset - deassert a submodule hardreset line and wait
- * @prm_mod: PRM submodule base (e.g. CORE_MOD)
- * @rst_shift: register bit shift corresponding to the reset line to deassert
- * @st_shift: register bit shift for the status of the deasserted submodule
- *
- * Some IPs like dsp or iva contain processors that require an HW
- * reset line to be asserted / deasserted in order to fully enable the
- * IP. These modules may have multiple hard-reset lines that reset
- * different 'submodules' inside the IP block. This function will
- * take the submodule out of reset and wait until the PRCM indicates
- * that the reset has completed before returning. Returns 0 upon success or
- * -EINVAL upon an argument error, -EEXIST if the submodule was already out
- * of reset, or -EBUSY if the submodule did not exit reset promptly.
- */
-int omap2_prm_deassert_hardreset(s16 prm_mod, u8 rst_shift, u8 st_shift)
-{
- u32 rst, st;
- int c;
-
- if (!(cpu_is_omap24xx() || cpu_is_omap34xx()))
- return -EINVAL;
-
- rst = 1 << rst_shift;
- st = 1 << st_shift;
-
- /* Check the current status to avoid de-asserting the line twice */
- if (omap2_prm_read_mod_bits_shift(prm_mod, OMAP2_RM_RSTCTRL, rst) == 0)
- return -EEXIST;
-
- /* Clear the reset status by writing 1 to the status bit */
- omap2_prm_rmw_mod_reg_bits(0xffffffff, st, prm_mod, OMAP2_RM_RSTST);
- /* de-assert the reset control line */
- omap2_prm_rmw_mod_reg_bits(rst, 0, prm_mod, OMAP2_RM_RSTCTRL);
- /* wait the status to be set */
- omap_test_timeout(omap2_prm_read_mod_bits_shift(prm_mod, OMAP2_RM_RSTST,
- st),
- MAX_MODULE_HARDRESET_WAIT, c);
-
- return (c == MAX_MODULE_HARDRESET_WAIT) ? -EBUSY : 0;
-}
-
/* PRM VP */
/*
@@ -348,18 +215,19 @@ static void __init omap3xxx_prm_enable_io_wakeup(void)
PM_WKEN);
}
-static int __init omap3xxx_prcm_init(void)
+static int __init omap3xxx_prm_init(void)
{
- int ret = 0;
+ int ret;
+
+ if (!cpu_is_omap34xx())
+ return 0;
- if (cpu_is_omap34xx()) {
- omap3xxx_prm_enable_io_wakeup();
- ret = omap_prcm_register_chain_handler(&omap3_prcm_irq_setup);
- if (!ret)
- irq_set_status_flags(omap_prcm_event_to_irq("io"),
- IRQ_NOAUTOEN);
- }
+ omap3xxx_prm_enable_io_wakeup();
+ ret = omap_prcm_register_chain_handler(&omap3_prcm_irq_setup);
+ if (!ret)
+ irq_set_status_flags(omap_prcm_event_to_irq("io"),
+ IRQ_NOAUTOEN);
return ret;
}
-subsys_initcall(omap3xxx_prcm_init);
+subsys_initcall(omap3xxx_prm_init);
diff --git a/arch/arm/mach-omap2/prm3xxx.h b/arch/arm/mach-omap2/prm3xxx.h
new file mode 100644
index 0000000..6821e83
--- /dev/null
+++ b/arch/arm/mach-omap2/prm3xxx.h
@@ -0,0 +1,158 @@
+/*
+ * OMAP3xxx Power/Reset Management (PRM) register definitions
+ *
+ * Copyright (C) 2007-2009, 2011-2012 Texas Instruments, Inc.
+ * Copyright (C) 2008-2010 Nokia Corporation
+ * Paul Walmsley
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * The PRM hardware modules on the OMAP2/3 are quite similar to each
+ * other. The PRM on OMAP4 has a new register layout, and is handled
+ * in a separate file.
+ */
+#ifndef __ARCH_ARM_MACH_OMAP2_PRM3XXX_H
+#define __ARCH_ARM_MACH_OMAP2_PRM3XXX_H
+
+#include "prcm-common.h"
+#include "prm.h"
+#include "prm2xxx_3xxx.h"
+
+#define OMAP34XX_PRM_REGADDR(module, reg) \
+ OMAP2_L4_IO_ADDRESS(OMAP3430_PRM_BASE + (module) + (reg))
+
+
+/*
+ * OMAP3-specific global PRM registers
+ * Use __raw_{read,write}l() with these registers.
+ *
+ * With a few exceptions, these are the register names beginning with
+ * PRM_* on 34xx. (The exceptions are the IRQSTATUS and IRQENABLE
+ * bits.)
+ */
+
+#define OMAP3_PRM_REVISION_OFFSET 0x0004
+#define OMAP3430_PRM_REVISION OMAP34XX_PRM_REGADDR(OCP_MOD, 0x0004)
+#define OMAP3_PRM_SYSCONFIG_OFFSET 0x0014
+#define OMAP3430_PRM_SYSCONFIG OMAP34XX_PRM_REGADDR(OCP_MOD, 0x0014)
+
+#define OMAP3_PRM_IRQSTATUS_MPU_OFFSET 0x0018
+#define OMAP3430_PRM_IRQSTATUS_MPU OMAP34XX_PRM_REGADDR(OCP_MOD, 0x0018)
+#define OMAP3_PRM_IRQENABLE_MPU_OFFSET 0x001c
+#define OMAP3430_PRM_IRQENABLE_MPU OMAP34XX_PRM_REGADDR(OCP_MOD, 0x001c)
+
+
+#define OMAP3_PRM_VC_SMPS_SA_OFFSET 0x0020
+#define OMAP3430_PRM_VC_SMPS_SA OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0020)
+#define OMAP3_PRM_VC_SMPS_VOL_RA_OFFSET 0x0024
+#define OMAP3430_PRM_VC_SMPS_VOL_RA OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0024)
+#define OMAP3_PRM_VC_SMPS_CMD_RA_OFFSET 0x0028
+#define OMAP3430_PRM_VC_SMPS_CMD_RA OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0028)
+#define OMAP3_PRM_VC_CMD_VAL_0_OFFSET 0x002c
+#define OMAP3430_PRM_VC_CMD_VAL_0 OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x002c)
+#define OMAP3_PRM_VC_CMD_VAL_1_OFFSET 0x0030
+#define OMAP3430_PRM_VC_CMD_VAL_1 OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0030)
+#define OMAP3_PRM_VC_CH_CONF_OFFSET 0x0034
+#define OMAP3430_PRM_VC_CH_CONF OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0034)
+#define OMAP3_PRM_VC_I2C_CFG_OFFSET 0x0038
+#define OMAP3430_PRM_VC_I2C_CFG OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0038)
+#define OMAP3_PRM_VC_BYPASS_VAL_OFFSET 0x003c
+#define OMAP3430_PRM_VC_BYPASS_VAL OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x003c)
+#define OMAP3_PRM_RSTCTRL_OFFSET 0x0050
+#define OMAP3430_PRM_RSTCTRL OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0050)
+#define OMAP3_PRM_RSTTIME_OFFSET 0x0054
+#define OMAP3430_PRM_RSTTIME OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0054)
+#define OMAP3_PRM_RSTST_OFFSET 0x0058
+#define OMAP3430_PRM_RSTST OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0058)
+#define OMAP3_PRM_VOLTCTRL_OFFSET 0x0060
+#define OMAP3430_PRM_VOLTCTRL OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0060)
+#define OMAP3_PRM_SRAM_PCHARGE_OFFSET 0x0064
+#define OMAP3430_PRM_SRAM_PCHARGE OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0064)
+#define OMAP3_PRM_CLKSRC_CTRL_OFFSET 0x0070
+#define OMAP3430_PRM_CLKSRC_CTRL OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0070)
+#define OMAP3_PRM_VOLTSETUP1_OFFSET 0x0090
+#define OMAP3430_PRM_VOLTSETUP1 OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0090)
+#define OMAP3_PRM_VOLTOFFSET_OFFSET 0x0094
+#define OMAP3430_PRM_VOLTOFFSET OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0094)
+#define OMAP3_PRM_CLKSETUP_OFFSET 0x0098
+#define OMAP3430_PRM_CLKSETUP OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x0098)
+#define OMAP3_PRM_POLCTRL_OFFSET 0x009c
+#define OMAP3430_PRM_POLCTRL OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x009c)
+#define OMAP3_PRM_VOLTSETUP2_OFFSET 0x00a0
+#define OMAP3430_PRM_VOLTSETUP2 OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00a0)
+#define OMAP3_PRM_VP1_CONFIG_OFFSET 0x00b0
+#define OMAP3430_PRM_VP1_CONFIG OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00b0)
+#define OMAP3_PRM_VP1_VSTEPMIN_OFFSET 0x00b4
+#define OMAP3430_PRM_VP1_VSTEPMIN OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00b4)
+#define OMAP3_PRM_VP1_VSTEPMAX_OFFSET 0x00b8
+#define OMAP3430_PRM_VP1_VSTEPMAX OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00b8)
+#define OMAP3_PRM_VP1_VLIMITTO_OFFSET 0x00bc
+#define OMAP3430_PRM_VP1_VLIMITTO OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00bc)
+#define OMAP3_PRM_VP1_VOLTAGE_OFFSET 0x00c0
+#define OMAP3430_PRM_VP1_VOLTAGE OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00c0)
+#define OMAP3_PRM_VP1_STATUS_OFFSET 0x00c4
+#define OMAP3430_PRM_VP1_STATUS OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00c4)
+#define OMAP3_PRM_VP2_CONFIG_OFFSET 0x00d0
+#define OMAP3430_PRM_VP2_CONFIG OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00d0)
+#define OMAP3_PRM_VP2_VSTEPMIN_OFFSET 0x00d4
+#define OMAP3430_PRM_VP2_VSTEPMIN OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00d4)
+#define OMAP3_PRM_VP2_VSTEPMAX_OFFSET 0x00d8
+#define OMAP3430_PRM_VP2_VSTEPMAX OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00d8)
+#define OMAP3_PRM_VP2_VLIMITTO_OFFSET 0x00dc
+#define OMAP3430_PRM_VP2_VLIMITTO OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00dc)
+#define OMAP3_PRM_VP2_VOLTAGE_OFFSET 0x00e0
+#define OMAP3430_PRM_VP2_VOLTAGE OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00e0)
+#define OMAP3_PRM_VP2_STATUS_OFFSET 0x00e4
+#define OMAP3430_PRM_VP2_STATUS OMAP34XX_PRM_REGADDR(OMAP3430_GR_MOD, 0x00e4)
+
+#define OMAP3_PRM_CLKSEL_OFFSET 0x0040
+#define OMAP3430_PRM_CLKSEL OMAP34XX_PRM_REGADDR(OMAP3430_CCR_MOD, 0x0040)
+#define OMAP3_PRM_CLKOUT_CTRL_OFFSET 0x0070
+#define OMAP3430_PRM_CLKOUT_CTRL OMAP34XX_PRM_REGADDR(OMAP3430_CCR_MOD, 0x0070)
+
+/* OMAP3 specific register offsets */
+#define OMAP3430ES2_PM_WKEN3 0x00f0
+#define OMAP3430ES2_PM_WKST3 0x00b8
+
+#define OMAP3430_PM_MPUGRPSEL 0x00a4
+#define OMAP3430_PM_MPUGRPSEL1 OMAP3430_PM_MPUGRPSEL
+#define OMAP3430ES2_PM_MPUGRPSEL3 0x00f8
+
+#define OMAP3430_PM_IVAGRPSEL 0x00a8
+#define OMAP3430_PM_IVAGRPSEL1 OMAP3430_PM_IVAGRPSEL
+#define OMAP3430ES2_PM_IVAGRPSEL3 0x00f4
+
+#define OMAP3430_PM_PREPWSTST 0x00e8
+
+#define OMAP3430_PRM_IRQSTATUS_IVA2 0x00f8
+#define OMAP3430_PRM_IRQENABLE_IVA2 0x00fc
+
+
+#ifndef __ASSEMBLER__
+
+/* OMAP3-specific VP functions */
+u32 omap3_prm_vp_check_txdone(u8 vp_id);
+void omap3_prm_vp_clear_txdone(u8 vp_id);
+
+/*
+ * OMAP3 access functions for voltage controller (VC) and
+ * voltage proccessor (VP) in the PRM.
+ */
+extern u32 omap3_prm_vcvp_read(u8 offset);
+extern void omap3_prm_vcvp_write(u32 val, u8 offset);
+extern u32 omap3_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
+
+extern void omap3xxx_prm_reconfigure_io_chain(void);
+
+/* PRM interrupt-related functions */
+extern void omap3xxx_prm_read_pending_irqs(unsigned long *events);
+extern void omap3xxx_prm_ocp_barrier(void);
+extern void omap3xxx_prm_save_and_clear_irqen(u32 *saved_mask);
+extern void omap3xxx_prm_restore_irqen(u32 *saved_mask);
+
+#endif /* __ASSEMBLER */
+
+
+#endif
diff --git a/arch/arm/mach-omap2/prm44xx.c b/arch/arm/mach-omap2/prm44xx.c
index f0c4d5f..06bb679 100644
--- a/arch/arm/mach-omap2/prm44xx.c
+++ b/arch/arm/mach-omap2/prm44xx.c
@@ -291,12 +291,13 @@ static void __init omap44xx_prm_enable_io_wakeup(void)
OMAP4_PRM_IO_PMCTRL_OFFSET);
}
-static int __init omap4xxx_prcm_init(void)
+static int __init omap4xxx_prm_init(void)
{
- if (cpu_is_omap44xx()) {
- omap44xx_prm_enable_io_wakeup();
- return omap_prcm_register_chain_handler(&omap4_prcm_irq_setup);
- }
- return 0;
+ if (!cpu_is_omap44xx())
+ return 0;
+
+ omap44xx_prm_enable_io_wakeup();
+
+ return omap_prcm_register_chain_handler(&omap4_prcm_irq_setup);
}
-subsys_initcall(omap4xxx_prcm_init);
+subsys_initcall(omap4xxx_prm_init);
diff --git a/arch/arm/mach-omap2/sdrc2xxx.c b/arch/arm/mach-omap2/sdrc2xxx.c
index 73e55e4..9abd6e2 100644
--- a/arch/arm/mach-omap2/sdrc2xxx.c
+++ b/arch/arm/mach-omap2/sdrc2xxx.c
@@ -31,7 +31,7 @@
#include "soc.h"
#include "iomap.h"
#include "common.h"
-#include "prm2xxx_3xxx.h"
+#include "prm2xxx.h"
#include "clock.h"
#include "sdrc.h"
diff --git a/arch/arm/mach-omap2/sleep34xx.S b/arch/arm/mach-omap2/sleep34xx.S
index 5069879..d83b918 100644
--- a/arch/arm/mach-omap2/sleep34xx.S
+++ b/arch/arm/mach-omap2/sleep34xx.S
@@ -31,7 +31,7 @@
#include "omap34xx.h"
#include "iomap.h"
#include "cm2xxx_3xxx.h"
-#include "prm2xxx_3xxx.h"
+#include "prm3xxx.h"
#include "sdrc.h"
#include "control.h"
diff --git a/arch/arm/mach-omap2/sram242x.S b/arch/arm/mach-omap2/sram242x.S
index 8f7326c..c720443 100644
--- a/arch/arm/mach-omap2/sram242x.S
+++ b/arch/arm/mach-omap2/sram242x.S
@@ -34,7 +34,7 @@
#include "soc.h"
#include "iomap.h"
-#include "prm2xxx_3xxx.h"
+#include "prm2xxx.h"
#include "cm2xxx_3xxx.h"
#include "sdrc.h"
diff --git a/arch/arm/mach-omap2/sram243x.S b/arch/arm/mach-omap2/sram243x.S
index b140d65..cfdc0bc 100644
--- a/arch/arm/mach-omap2/sram243x.S
+++ b/arch/arm/mach-omap2/sram243x.S
@@ -34,7 +34,7 @@
#include "soc.h"
#include "iomap.h"
-#include "prm2xxx_3xxx.h"
+#include "prm2xxx.h"
#include "cm2xxx_3xxx.h"
#include "sdrc.h"
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
