2012/9/18 Mark Jackson <mpfj-list@xxxxxxxxxx>: > I'm using a BeagleBone, and the linux kernel from Koen Kooi (https://github.com/koenkooi/linux.git). > > I have noticed there is a 0.5sec delay between OMAP UART0 being initialised and the console being > enabled. > > I'll dig a bit deeper, but can anyone shed light on what the delay is ? > I think it is the time taken by the console spitting all of it's accumulated printk. In other words, when the console comes up, all the preceding printks are written in one go on the serial port at 115200 bauds. a quick wc on your bootlog leads to a byte count over 6000 at ten bits (8 bits + start + stop) per byte you need 60000 /115200 ie 520 milliseconds. Try booting with the quiet command line argument, look at the dmesg output, delay should be gone > Can this delay be removed ? > > My total boot time is only 1.3sec, so a 0.5sec delay is quite significant !?! > > Below is the first portion of my boot log. > > Thanks for any advice > Mark JACKSON > --- > [ 0.000000] Initializing cgroup subsys cpu > [ 0.000000] Linux version 3.2.28+ (mpfj@mpfj-nanobone) (gcc version 4.5.4 (Buildroot > 2012.08-git-00388-g7019407) ) #20 Thu Sep 13 16:56:56 BST 2012 > [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c53c7d > [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache > [ 0.000000] Machine: am335xevm > [ 0.000000] Memory policy: ECC disabled, Data cache writeback > [ 0.000000] AM335X ES1.0 (sgx neon ) > [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024 > [ 0.000000] Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p2 ro rootfstype=ext2 > rootwait ip=none > [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) > [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) > [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) > [ 0.000000] Memory: 256MB = 256MB total > [ 0.000000] Memory: 253868k/253868k available, 8276k reserved, 0K highmem > [ 0.000000] Virtual kernel memory layout: > [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) > [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) > [ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) > [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) > [ 0.000000] modules : 0xbf800000 - 0xc0000000 ( 8 MB) > [ 0.000000] .text : 0xc0008000 - 0xc04ddadc (4951 kB) > [ 0.000000] .init : 0xc04de000 - 0xc0517000 ( 228 kB) > [ 0.000000] .data : 0xc0518000 - 0xc056e3a8 ( 345 kB) > [ 0.000000] .bss : 0xc056e3cc - 0xc05d8a54 ( 426 kB) > [ 0.000000] NR_IRQS:410 nr_irqs:410 410 > [ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts > [ 0.000000] Total of 128 interrupts on 1 active controller > [ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz > [ 0.000000] OMAP clocksource: GPTIMER1 at 32768 Hz > [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 30517ns, wraps every 131071999ms > [ 0.000000] Console: colour dummy device 80x30 > [ 0.000183] Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) > [ 0.058166] pid_max: default: 32768 minimum: 301 > [ 0.058319] Security Framework initialized > [ 0.058410] Mount-cache hash table entries: 512 > [ 0.058837] Initializing cgroup subsys cpuacct > [ 0.058898] Initializing cgroup subsys devices > [ 0.058898] Initializing cgroup subsys freezer > [ 0.058990] CPU: Testing write buffer coherency: ok > [ 0.060180] devtmpfs: initialized > [ 0.080780] omap_hwmod: gfx: failed to hardreset > [ 0.097503] omap_hwmod: pruss: failed to hardreset > [ 0.098114] print_constraints: dummy: > [ 0.098419] NET: Registered protocol family 16 > [ 0.099731] OMAP GPIO hardware version 0.1 > [ 0.101043] omap_mux_init: Add partition: #1: core, flags: 0 > [ 0.102661] omap_i2c.1: alias fck already exists > [ 0.103057] hw-breakpoint: debug architecture 0x4 unsupported. > [ 0.103240] omap2_mcspi.1: alias fck already exists > [ 0.103393] omap2_mcspi.2: alias fck already exists > [ 0.103607] edma.0: alias fck already exists > [ 0.103637] edma.0: alias fck already exists > [ 0.103668] edma.0: alias fck already exists > [ 0.103759] cape: pcm register > [ 0.114685] bio: create slab <bio-0> at 0 > [ 0.116027] SCSI subsystem initialized > [ 0.117004] usbcore: registered new interface driver usbfs > [ 0.117156] usbcore: registered new interface driver hub > [ 0.117340] usbcore: registered new device driver usb > [ 0.117523] musb-ti81xx musb-ti81xx: musb0, board_mode=0x13, plat_mode=0x3 > [ 0.117675] musb-ti81xx musb-ti81xx: musb1, board_mode=0x13, plat_mode=0x1 > [ 0.118316] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz > [ 0.119598] Advanced Linux Sound Architecture Driver Version 1.0.24. > [ 0.120239] Switching to clocksource gp timer > [ 0.148681] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) > [ 0.148895] musb-hdrc musb-hdrc.0: dma type: pio > [ 0.149078] MUSB0 controller's USBSS revision = 4ea20800 > [ 0.149627] musb-hdrc musb-hdrc.0: USB OTG mode controller at d081c000 using PIO, IRQ 18 > [ 0.149932] musb-hdrc musb-hdrc.1: dma type: pio > [ 0.150115] MUSB1 controller's USBSS revision = 4ea20800 > [ 0.150268] musb-hdrc musb-hdrc.1: MUSB HDRC host driver > [ 0.150451] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 1 > [ 0.150604] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 > [ 0.150634] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 > [ 0.150665] usb usb1: Product: MUSB HDRC host driver > [ 0.150665] usb usb1: Manufacturer: Linux 3.2.28+ musb-hcd > [ 0.150695] usb usb1: SerialNumber: musb-hdrc.1 > [ 0.151519] hub 1-0:1.0: USB hub found > [ 0.151550] hub 1-0:1.0: 1 port detected > [ 0.152099] musb-hdrc musb-hdrc.1: USB Host mode controller at d081e800 using PIO, IRQ 19 > [ 0.152557] NET: Registered protocol family 2 > [ 0.152801] IP route cache hash table entries: 2048 (order: 1, 8192 bytes) > [ 0.153289] TCP established hash table entries: 8192 (order: 4, 65536 bytes) > [ 0.153503] TCP bind hash table entries: 8192 (order: 3, 32768 bytes) > [ 0.153656] TCP: Hash tables configured (established 8192 bind 8192) > [ 0.153656] TCP reno registered > [ 0.153686] UDP hash table entries: 256 (order: 0, 4096 bytes) > [ 0.153717] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) > [ 0.154052] NET: Registered protocol family 1 > [ 0.154449] RPC: Registered named UNIX socket transport module. > [ 0.154479] RPC: Registered udp transport module. > [ 0.154479] RPC: Registered tcp transport module. > [ 0.154510] RPC: Registered tcp NFSv4.1 backchannel transport module. > [ 0.156555] audit: initializing netlink socket (disabled) > [ 0.156616] type=2000 audit(0.150:1): initialized > [ 0.158172] VFS: Disk quotas dquot_6.5.2 > [ 0.158264] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 0.159545] msgmni has been set to 495 > [ 0.161010] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) > [ 0.161041] io scheduler noop registered > [ 0.161071] io scheduler deadline registered > [ 0.161132] io scheduler cfq registered (default) > [ 0.162231] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled > [ 0.163848] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0 > [ 0.757232] console [ttyO0] enabled > [ 0.761535] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1 > [ 0.769409] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2 > [ 0.777282] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3 > [ 0.785156] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4 > [ 0.792999] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5 > ... > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
