Re: [PATCH 6/6] OMAPDSS: VENC: Maintian copy of video output polarity in private data

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thursday 16 August 2012 05:08 PM, Tomi Valkeinen wrote:
On Thu, 2012-08-16 at 13:06 +0530, Archit Taneja wrote:
The VENC driver currently relies on the omap_dss_device struct to configure the
video output polarity. This makes the VENC interface driver dependent on the
omap_dss_device struct.

Make the VENC driver data maintain it's own polarity field. A panel driver
is expected to call omapdss_venc_set_vid_out_polarity() before enabling the
interface.

Signed-off-by: Archit Taneja <archit@xxxxxx>
---
  drivers/video/omap2/dss/dss.h        |    2 ++
  drivers/video/omap2/dss/venc.c       |   13 ++++++++++++-
  drivers/video/omap2/dss/venc_panel.c |    6 ++++++
  3 files changed, 20 insertions(+), 1 deletion(-)

diff --git a/drivers/video/omap2/dss/dss.h b/drivers/video/omap2/dss/dss.h
index c17d298..b2cf5530 100644
--- a/drivers/video/omap2/dss/dss.h
+++ b/drivers/video/omap2/dss/dss.h
@@ -479,6 +479,8 @@ u32 omapdss_venc_get_wss(struct omap_dss_device *dssdev);
  int omapdss_venc_set_wss(struct omap_dss_device *dssdev, u32 wss);
  void omapdss_venc_set_type(struct omap_dss_device *dssdev,
  		enum omap_dss_venc_type type);
+void omapdss_venc_set_vid_out_polarity(struct omap_dss_device *dssdev,
+		enum omap_dss_signal_level vid_out_pol);
  int venc_panel_init(void);
  void venc_panel_exit(void);

diff --git a/drivers/video/omap2/dss/venc.c b/drivers/video/omap2/dss/venc.c
index 2d90fcf..8cb372f 100644
--- a/drivers/video/omap2/dss/venc.c
+++ b/drivers/video/omap2/dss/venc.c
@@ -303,6 +303,7 @@ static struct {

  	struct omap_video_timings timings;
  	enum omap_dss_venc_type type;
+	enum omap_dss_signal_level vid_out_pol;
  } venc;

  static inline void venc_write_reg(int idx, u32 val)
@@ -447,7 +448,7 @@ static int venc_power_on(struct omap_dss_device *dssdev)
  	else /* S-Video */
  		l |= (1 << 0) | (1 << 2);

-	if (dssdev->phy.venc.invert_polarity == false)
+	if (venc.vid_out_pol == OMAPDSS_SIG_ACTIVE_HIGH)
  		l |= 1 << 3;

Are you sure this is correct? I know practically nothing about analog
TV, but the TRM doesn't seem to say much about that bit, except it can
be used to "invert the video output". It doesn't say there's an
active/inactive level for the signal.

Well, the code works :), I'm also not totally sure about whether it should be represented as a 2-level signal, it seemed like it would be nicer to give it a signal level rather than keeping it as a bool, which could vary for other SoC's?

I am considering not to pass this via the panel driver for now, I don't know if all VENC IPs needs to do this, maybe it's okay to leave this dssdev reference for now?

Archit


  Tomi


--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux