Hi Daniel > > >>> This series of patches adds, > > >>> a) Multi instances support in musb driver > > >>> b) DT support for musb_dsps glue layer > > >>> c) DT support for NOP transceiver > > >>> > > >>> AM33xx and TI81xx has dual musb controller and has two usb > > >> PHY of same type. > > >>> This patch series uses 'phandle' based API > > >>> devm_usb_get_phy_by_phandle() to get the PHY of same type. This > > >>> API support is being added by Kishon's patch discussed at [1] > > >>> > > >>> The series applies to linux-omap (master branch) > > >>> + Vaibhav baseport patches on his tree at [3] > > >>> + Kishon's multi phy patches on Felipe's branch 'xceiv' > > >>> + Kishon's patch on phandle at [1] > > >>> + AM33xx musb glue compile and bugfix patches at [4], > > >> [5], [6] and [7] > > >>> + Damodar's recent patch at [2] > > >>> > > >>> and have been tested on Beaglebone board. > > > > > > Have you applied the above patches before applying these patches. > > > > Somehow, I was missing some of Ajay's patches. I resolved that, and > > now the series applied. > > > > However, I needed to add a phandle "usb0-phy = <&usb0_phy>" to the > > usb_otg_hs DTSI block, otherwise devm_usb_get_phy_by_phandle() in > > drivers/usb/musb/musb_dsps.c would fail. Is that correct? I > can't seem > > to find that in your patches. > > It's getting done in patch 11/11. Refer patch 11/11 available at http://marc.info/?l=linux-usb&m=134390988804627&w=2 Ravi Babu > > > > > With this addition, I see the following: > > > > [ 1.782180] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) > > [ 1.809966] musb-hdrc musb-hdrc.0: MUSB HDRC host driver > > [ 1.819068] musb-hdrc musb-hdrc.0: new USB bus > registered, assigned > > bus number 1 > > [ 1.827970] usb usb1: New USB device found, idVendor=1d6b, > > idProduct=0002 > > [ 1.835184] usb usb1: New USB device strings: Mfr=3, Product=2, > > SerialNumber=1 > > [ 1.842818] usb usb1: Product: MUSB HDRC host driver > > [ 1.848031] usb usb1: Manufacturer: Linux > > 3.6.0-rc1-00038-g8a1ec8f-dirty musb-hcd > > [ 1.855933] usb usb1: SerialNumber: musb-hdrc.0 > > [ 1.866913] hub 1-0:1.0: USB hub found > > [ 1.871192] hub 1-0:1.0: 1 port detected > > [ 1.878106] musb-hdrc musb-hdrc.0: USB Host mode controller at > > d08c0000 using PIO, IRQ 18 > > > > ... but no USB functions. Also, every two seconds, the following > > message is > > printed: > > > > [ 11.036608] musb_bus_suspend 2308: trying to suspend as > a_wait_vrise > > while active > > [ 13.044811] musb_bus_suspend 2308: trying to suspend as > a_wait_vrise > > while active > > [ 15.052196] musb_bus_suspend 2308: trying to suspend as > a_wait_vrise > > while active > > Do you see them even when you connect a device to port? > > Ajay > > > > > > Anything obvious that I'm missing? > > > > > > Thanks, > > Daniel > > -- > > To unsubscribe from this list: send the line "unsubscribe > linux-usb" > > in the body of a message to majordomo@xxxxxxxxxxxxxxx More > majordomo > > info at http://vger.kernel.org/majordomo-info.html > -------------------------------------------------------------- > --------------------- > This email message is for the sole use of the intended > recipient(s) and may contain confidential information. Any > unauthorized review, use, disclosure or distribution is > prohibited. If you are not the intended recipient, please > contact the sender by reply email and destroy all copies of > the original message. > -------------------------------------------------------------- > --------------------- > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
