Hi,
On Wed, Jul 11, 2012 at 3:59 PM, Damodar Santhapuri <x0132156@xxxxxx> wrote:
> From: Ajay Kumar Gupta <ajay.gupta@xxxxxx>
>
> AM335x uses NOP transceiver driver and need to enable builtin PHY
> by writing into usb_ctrl register available in system control
> module register space. This is being added at musb glue driver
> layer untill a separate system control module driver is available.
>
> Signed-off-by: Ajay Kumar Gupta <ajay.gupta@xxxxxx>
> Signed-off-by: Damodar Santhapuri <x0132156@xxxxxx>
> ---
> Changes from v0:
> - Used platform_get_resource() instead of platform_get_resource_byname()
> based on Kishon's comment.
>
> arch/arm/mach-omap2/board-ti8168evm.c | 1 -
> arch/arm/mach-omap2/omap_phy_internal.c | 35 ------------
> arch/arm/plat-omap/include/plat/usb.h | 5 +-
> drivers/usb/musb/musb_dsps.c | 87 +++++++++++++++++++++++++------
> 4 files changed, 73 insertions(+), 55 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/board-ti8168evm.c b/arch/arm/mach-omap2/board-ti8168evm.c
> index d4c8392..0c7c098 100644
> --- a/arch/arm/mach-omap2/board-ti8168evm.c
> +++ b/arch/arm/mach-omap2/board-ti8168evm.c
> @@ -26,7 +26,6 @@
> #include <plat/usb.h>
>
> static struct omap_musb_board_data musb_board_data = {
> - .set_phy_power = ti81xx_musb_phy_power,
> .interface_type = MUSB_INTERFACE_ULPI,
> .mode = MUSB_OTG,
> .power = 500,
> diff --git a/arch/arm/mach-omap2/omap_phy_internal.c b/arch/arm/mach-omap2/omap_phy_internal.c
> index d52651a..d80bb16 100644
> --- a/arch/arm/mach-omap2/omap_phy_internal.c
> +++ b/arch/arm/mach-omap2/omap_phy_internal.c
> @@ -254,38 +254,3 @@ void am35x_set_mode(u8 musb_mode)
>
> omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
> }
> -
> -void ti81xx_musb_phy_power(u8 on)
> -{
> - void __iomem *scm_base = NULL;
> - u32 usbphycfg;
> -
> - scm_base = ioremap(TI81XX_SCM_BASE, SZ_2K);
> - if (!scm_base) {
> - pr_err("system control module ioremap failed\n");
> - return;
> - }
> -
> - usbphycfg = __raw_readl(scm_base + USBCTRL0);
> -
> - if (on) {
> - if (cpu_is_ti816x()) {
> - usbphycfg |= TI816X_USBPHY0_NORMAL_MODE;
> - usbphycfg &= ~TI816X_USBPHY_REFCLK_OSC;
> - } else if (cpu_is_ti814x()) {
> - usbphycfg &= ~(USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN
> - | USBPHY_DPINPUT | USBPHY_DMINPUT);
> - usbphycfg |= (USBPHY_OTGVDET_EN | USBPHY_OTGSESSEND_EN
> - | USBPHY_DPOPBUFCTL | USBPHY_DMOPBUFCTL);
> - }
> - } else {
> - if (cpu_is_ti816x())
> - usbphycfg &= ~TI816X_USBPHY0_NORMAL_MODE;
> - else if (cpu_is_ti814x())
> - usbphycfg |= USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN;
> -
> - }
> - __raw_writel(usbphycfg, scm_base + USBCTRL0);
> -
> - iounmap(scm_base);
> -}
> diff --git a/arch/arm/plat-omap/include/plat/usb.h b/arch/arm/plat-omap/include/plat/usb.h
> index 548a4c8..c2aa4ae 100644
> --- a/arch/arm/plat-omap/include/plat/usb.h
> +++ b/arch/arm/plat-omap/include/plat/usb.h
> @@ -95,7 +95,6 @@ extern void am35x_musb_reset(void);
> extern void am35x_musb_phy_power(u8 on);
> extern void am35x_musb_clear_irq(void);
> extern void am35x_set_mode(u8 musb_mode);
> -extern void ti81xx_musb_phy_power(u8 on);
>
> /* AM35x */
> /* USB 2.0 PHY Control */
> @@ -120,8 +119,8 @@ extern void ti81xx_musb_phy_power(u8 on);
> #define CONF2_DATPOL (1 << 1)
>
> /* TI81XX specific definitions */
> -#define USBCTRL0 0x620
> -#define USBSTAT0 0x624
> +#define MUSB_USBSS_REV_816X 0x9
> +#define MUSB_USBSS_REV_814X 0xb
>
> /* TI816X PHY controls bits */
> #define TI816X_USBPHY0_NORMAL_MODE (1 << 0)
> diff --git a/drivers/usb/musb/musb_dsps.c b/drivers/usb/musb/musb_dsps.c
> index 494772f..72eda64 100644
> --- a/drivers/usb/musb/musb_dsps.c
> +++ b/drivers/usb/musb/musb_dsps.c
> @@ -115,9 +115,46 @@ struct dsps_glue {
> struct platform_device *musb; /* child musb pdev */
> const struct dsps_musb_wrapper *wrp; /* wrapper register offsets */
> struct timer_list timer; /* otg_workaround timer */
> + u32 __iomem *usb_ctrl;
> + u8 usbss_rev;
> };
>
> /**
> + * musb_dsps_phy_control - phy on/off
> + * @glue: struct dsps_glue *
> + * @on: flag for phy to be switched on or off
> + *
> + * This is to enable the PHY using usb_ctrl register in system control
> + * module space.
> + *
> + * XXX: This function will be removed once we have a seperate driver for
> + * control module
> + */
> +static void musb_dsps_phy_control(struct dsps_glue *glue, u8 on)
I think this function should be added in your transceiver driver. I
don't see glue as an appropriate place for this.
> +{
> + u32 usbphycfg;
> +
> + usbphycfg = __raw_readl(glue->usb_ctrl);
> +
> + if (on) {
> + if (glue->usbss_rev == MUSB_USBSS_REV_816X) {
> + usbphycfg |= TI816X_USBPHY0_NORMAL_MODE;
> + usbphycfg &= ~TI816X_USBPHY_REFCLK_OSC;
> + } else if (glue->usbss_rev == MUSB_USBSS_REV_814X) {
> + usbphycfg &= ~(USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN
> + | USBPHY_DPINPUT | USBPHY_DMINPUT);
> + usbphycfg |= (USBPHY_OTGVDET_EN | USBPHY_OTGSESSEND_EN
> + | USBPHY_DPOPBUFCTL | USBPHY_DMOPBUFCTL);
> + }
> + } else {
> + if (glue->usbss_rev == MUSB_USBSS_REV_816X)
> + usbphycfg &= ~TI816X_USBPHY0_NORMAL_MODE;
> + else if (glue->usbss_rev == MUSB_USBSS_REV_814X)
> + usbphycfg |= USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN;
> + }
> + __raw_writel(usbphycfg, glue->usb_ctrl);
> +}
> +/**
Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
