On 06/27/2012 04:43 PM, Jon Hunter wrote:
Hi Franky,
On 06/25/2012 03:52 PM, Franky Lin wrote:
Hi Kevin, Tarun,
We are using the expansion connector A on Panda board to mount a SDIO
WiFi dongle on MMC2 with a level triggered interrupt signal connected to
GPIO 138. It's been working fine until 3.5 rc1. The board hang randomly
within 5 mins during a network traffic test. After bisecting we found
the culprit is "[PATCH 8/8] gpio/omap: fix missing check in
*_runtime_suspend()" [1].
I have been looking into this today to see if I can replicate the
problem that you have reported. However, so far I have not had any luck.
Please note that my test setup is not exactly the same as yours as I
don't have your wlan module. However, I have been using a 2nd board to
generate gpio events to a panda-es to see I can make it lock up. I have
tried mainline kernel 3.5-rc1 and 3.5-rc3 but I have not seen any
problems after sending 100k gpio events (over many minutes). My setup is
as follows ...
- OMAP4460 panda-es with gpio-138 connected to OMAP3430 beagle gpio-11.
- Mainline kernel 3.5-rc1/3 using omap2plus_defconfig (no changes)
- Created a simple kernel module that acquires gpio-138 and sets up a
IRQ with flag IRQF_TRIGGER_HIGH (for active high level interrupt).
- GPIO events are triggered roughly every 1ms
Don't know if it's related, but we also mux several other pins on
connector A:
/* MMC2 Mux for extension board */
/* MMC2 CMD */
OMAP4_MUX(GPMC_NWE, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
/* MMC2 CLK */
OMAP4_MUX(GPMC_NOE, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
/* MMC2 DAT 0-3 */
OMAP4_MUX(GPMC_AD0, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
OMAP4_MUX(GPMC_AD1, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
OMAP4_MUX(GPMC_AD2, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
OMAP4_MUX(GPMC_AD3, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
/* GPIO MUX for OOB interupt of dongle */
OMAP4_MUX(MCSPI1_CS1, OMAP_MUX_MODE3 | OMAP_PIN_INPUT_PULLDOWN),
/* GPIO MUX for WLAN_ENABLE for dongle */
OMAP4_MUX(MCSPI1_CLK, OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT),
Can you confirm ...
1. You are just using omap2plus_defconfig with no changes?
No, we enable following options
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
CONFIG_USB_OHCI_HCD=y
2. Rough frequency of gpio events?
3367 interrupts were triggered during a 10 secs throughput test.
3. Is the gpio configured for active low or high?
active high
4. When the hang occurs, what is the state of the gpio? Active or
inactive? Can you probe it with a scope? If it was always active I
could see that this would lock the device up, but I am not sure how
that would relate to the results from your bisect???
I dont have a scope nearby. Let me see if I can find one tomorrow.
I noticed Kevin raised some similar cases on other platforms and also
provided two patches in the patch mail thread. But unfortunately those
two patches doesn't help in our case. I tested the driver with 3.5-rc3
mainline kernel and the issue is still there. I can only "fix" the hang
by either reverting the commit or disabling CONFIG_PM_RUNTIME. Also, the
hang only happens on Panda ES board. Old Panda with 4430 works good.
It does not make sense to me yet why this would only impact 4460, but I
will keep this in mind.
In your wlan driver are you acquiring and freeing the gpio often? Or are
you only acquiring the gpio on boot?
The reason I ask is because for omap4, it seems that we are not
currently calling omap2_gpio_prepare_for_idle() during idle and so the
only time I see us call the runtime_suspend/resume handlers for omap4 is
during probe and when we acquire and free the gpio.
So if you were not acquiring and freeing the gpio and are using the
stock kernel, then as far as I can tell, the runtime pm code is not
being exercised much. My test is not acquiring and releasing the gpio
and so I am wondering if that is the secret to reproducing this problem :-)
We only request the irq once during initialization. But we do frequently
disable and re-enable it since we need to access to the module through
SDIO to clear the interrupt. Apparently we can't finish all this in irq
handler.
Hope these could help.
Regards,
Franky
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
