Hi Tony
On Mon, 23 Apr 2012, Tony Lindgren wrote:
> This allows us to pass dma request lines in platform data to
> MMC driver the same way as we already do for omap2430 and later.
>
> Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
This might save you some time, I updated this patch to move the device
creation code to arch/arm/mach-omap2/msdi.c and to change the hwmod name
to 'msdi1' to conform with the new data. Updated patch below.
- Paul
From: Tony Lindgren <tony@xxxxxxxxxxx>
Date: Mon, 23 Apr 2012 17:08:35 -0700
Subject: [PATCH] ARM: OMAP2: Use hwmod to initialize mmc for 2420
This allows us to pass dma request lines in platform data to
MMC driver the same way as we already do for omap2430 and later.
Signed-off-by: Tony Lindgren <tony@xxxxxxxxxxx>
---
arch/arm/mach-omap2/devices.c | 59 -----------------------------------
arch/arm/mach-omap2/msdi.c | 68 +++++++++++++++++++++++++++++++++++++++++
2 files changed, 68 insertions(+), 59 deletions(-)
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index e433603..263a85f 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -27,7 +27,6 @@
#include "iomap.h"
#include <plat/board.h>
-#include <plat/mmc.h>
#include <plat/dma.h>
#include <plat/omap_hwmod.h>
#include <plat/omap_device.h>
@@ -574,64 +573,6 @@ static inline void omap_init_aes(void) { }
/*-------------------------------------------------------------------------*/
-#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
-
-static inline void omap242x_mmc_mux(struct omap_mmc_platform_data
- *mmc_controller)
-{
- if ((mmc_controller->slots[0].switch_pin > 0) && \
- (mmc_controller->slots[0].switch_pin < OMAP_MAX_GPIO_LINES))
- omap_mux_init_gpio(mmc_controller->slots[0].switch_pin,
- OMAP_PIN_INPUT_PULLUP);
- if ((mmc_controller->slots[0].gpio_wp > 0) && \
- (mmc_controller->slots[0].gpio_wp < OMAP_MAX_GPIO_LINES))
- omap_mux_init_gpio(mmc_controller->slots[0].gpio_wp,
- OMAP_PIN_INPUT_PULLUP);
-
- omap_mux_init_signal("sdmmc_cmd", 0);
- omap_mux_init_signal("sdmmc_clki", 0);
- omap_mux_init_signal("sdmmc_clko", 0);
- omap_mux_init_signal("sdmmc_dat0", 0);
- omap_mux_init_signal("sdmmc_dat_dir0", 0);
- omap_mux_init_signal("sdmmc_cmd_dir", 0);
- if (mmc_controller->slots[0].caps & MMC_CAP_4_BIT_DATA) {
- omap_mux_init_signal("sdmmc_dat1", 0);
- omap_mux_init_signal("sdmmc_dat2", 0);
- omap_mux_init_signal("sdmmc_dat3", 0);
- omap_mux_init_signal("sdmmc_dat_dir1", 0);
- omap_mux_init_signal("sdmmc_dat_dir2", 0);
- omap_mux_init_signal("sdmmc_dat_dir3", 0);
- }
-
- /*
- * Use internal loop-back in MMC/SDIO Module Input Clock
- * selection
- */
- if (mmc_controller->slots[0].internal_clock) {
- u32 v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
- v |= (1 << 24);
- omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
- }
-}
-
-void __init omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data)
-{
- char *name = "mmci-omap";
-
- if (!mmc_data[0]) {
- pr_err("%s fails: Incomplete platform data\n", __func__);
- return;
- }
-
- omap242x_mmc_mux(mmc_data[0]);
- omap_mmc_add(name, 0, OMAP2_MMC1_BASE, OMAP2420_MMC_SIZE,
- INT_24XX_MMC_IRQ, mmc_data[0]);
-}
-
-#endif
-
-/*-------------------------------------------------------------------------*/
-
#if defined(CONFIG_HDQ_MASTER_OMAP) || defined(CONFIG_HDQ_MASTER_OMAP_MODULE)
#define OMAP_HDQ_BASE 0x480B2000
static struct resource omap_hdq_resources[] = {
diff --git a/arch/arm/mach-omap2/msdi.c b/arch/arm/mach-omap2/msdi.c
index ef2a692..d75839a 100644
--- a/arch/arm/mach-omap2/msdi.c
+++ b/arch/arm/mach-omap2/msdi.c
@@ -24,9 +24,11 @@
#include <linux/kernel.h>
#include <plat/omap_hwmod.h>
+#include <plat/omap_device.h>
#include <plat/mmc.h>
#include "common.h"
+#include "mux.h"
/*
* MSDI_CON_OFFSET: offset in bytes of the MSDI IP block's CON register
@@ -86,3 +88,69 @@ int omap_msdi_reset(struct omap_hwmod *oh)
return 0;
}
+
+static inline void omap242x_mmc_mux(struct omap_mmc_platform_data
+ *mmc_controller)
+{
+ if ((mmc_controller->slots[0].switch_pin > 0) && \
+ (mmc_controller->slots[0].switch_pin < OMAP_MAX_GPIO_LINES))
+ omap_mux_init_gpio(mmc_controller->slots[0].switch_pin,
+ OMAP_PIN_INPUT_PULLUP);
+ if ((mmc_controller->slots[0].gpio_wp > 0) && \
+ (mmc_controller->slots[0].gpio_wp < OMAP_MAX_GPIO_LINES))
+ omap_mux_init_gpio(mmc_controller->slots[0].gpio_wp,
+ OMAP_PIN_INPUT_PULLUP);
+
+ omap_mux_init_signal("sdmmc_cmd", 0);
+ omap_mux_init_signal("sdmmc_clki", 0);
+ omap_mux_init_signal("sdmmc_clko", 0);
+ omap_mux_init_signal("sdmmc_dat0", 0);
+ omap_mux_init_signal("sdmmc_dat_dir0", 0);
+ omap_mux_init_signal("sdmmc_cmd_dir", 0);
+ if (mmc_controller->slots[0].caps & MMC_CAP_4_BIT_DATA) {
+ omap_mux_init_signal("sdmmc_dat1", 0);
+ omap_mux_init_signal("sdmmc_dat2", 0);
+ omap_mux_init_signal("sdmmc_dat3", 0);
+ omap_mux_init_signal("sdmmc_dat_dir1", 0);
+ omap_mux_init_signal("sdmmc_dat_dir2", 0);
+ omap_mux_init_signal("sdmmc_dat_dir3", 0);
+ }
+
+ /*
+ * Use internal loop-back in MMC/SDIO Module Input Clock
+ * selection
+ */
+ if (mmc_controller->slots[0].internal_clock) {
+ u32 v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
+ v |= (1 << 24);
+ omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
+ }
+}
+
+void __init omap242x_init_mmc(struct omap_mmc_platform_data **mmc_data)
+{
+ struct platform_device *pdev;
+ struct omap_hwmod *oh;
+ int id = 0;
+ char *oh_name = "msdi1";
+ char *dev_name = "mmci-omap";
+
+ if (!mmc_data[0]) {
+ pr_err("%s fails: Incomplete platform data\n", __func__);
+ return;
+ }
+
+ omap242x_mmc_mux(mmc_data[0]);
+
+ oh = omap_hwmod_lookup(oh_name);
+ if (!oh) {
+ pr_err("Could not look up %s\n", oh_name);
+ return;
+ }
+ pdev = omap_device_build(dev_name, id, oh, mmc_data[0],
+ sizeof(struct omap_mmc_platform_data), NULL, 0, 0);
+ if (IS_ERR(pdev))
+ WARN(1, "Can'd build omap_device for %s:%s.\n",
+ dev_name, oh->name);
+}
+
--
1.7.10
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
