Hi Govindraj,
On 3/28/2012 6:09, Raja, Govindraj wrote:
On Wed, Mar 28, 2012 at 2:38 AM, Jon Hunter<jon-hunter@xxxxxx> wrote:
Hi Govindraj,
On 3/21/2012 5:24, Govindraj.R wrote:
From: "Govindraj.R"<govindraj.raja@xxxxxx>
Currently the errata is populated based on cpu checks this can
be removed and replaced with module version check of uart ip block.
MVR reg is provided within the uart reg map use the same
to populate the errata and thus now errata population and handling
can be managed within the driver itself.
Cc: Paul Walmsley<paul@xxxxxxxxx>
Cc: Kevin Hilman<khilman@xxxxxx>
Signed-off-by: Felipe Balbi<balbi@xxxxxx>
Signed-off-by: Govindraj.R<govindraj.raja@xxxxxx>
---
arch/arm/mach-omap2/serial.c | 8 ---
arch/arm/plat-omap/include/plat/omap-serial.h | 1 -
drivers/tty/serial/omap-serial.c | 62
++++++++++++++++++++++++-
3 files changed, 61 insertions(+), 10 deletions(-)
diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c
index f590afc..330ee04 100644
--- a/arch/arm/mach-omap2/serial.c
+++ b/arch/arm/mach-omap2/serial.c
@@ -357,14 +357,6 @@ void __init omap_serial_init_port(struct
omap_board_data *bdata,
omap_up.dma_rx_poll_rate = info->dma_rx_poll_rate;
omap_up.autosuspend_timeout = info->autosuspend_timeout;
- /* Enable the MDR1 Errata i202 for OMAP2430/3xxx/44xx */
- if (!cpu_is_omap2420()&& !cpu_is_ti816x())
- omap_up.errata |= UART_ERRATA_i202_MDR1_ACCESS;
-
- /* Enable DMA Mode Force Idle Errata i291 for omap34xx/3630 */
- if (cpu_is_omap34xx() || cpu_is_omap3630())
- omap_up.errata |= UART_ERRATA_i291_DMA_FORCEIDLE;
-
pdata =&omap_up;
pdata_size = sizeof(struct omap_uart_port_info);
diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h
b/arch/arm/plat-omap/include/plat/omap-serial.h
index 9ff4444..1a52725 100644
--- a/arch/arm/plat-omap/include/plat/omap-serial.h
+++ b/arch/arm/plat-omap/include/plat/omap-serial.h
@@ -65,7 +65,6 @@ struct omap_uart_port_info {
bool dma_enabled; /* To specify DMA Mode */
unsigned int uartclk; /* UART clock rate */
upf_t flags; /* UPF_* flags */
- u32 errata;
unsigned int dma_rx_buf_size;
unsigned int dma_rx_timeout;
unsigned int autosuspend_timeout;
diff --git a/drivers/tty/serial/omap-serial.c
b/drivers/tty/serial/omap-serial.c
index f809041..c7666d6 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -44,6 +44,13 @@
#include<plat/dmtimer.h>
#include<plat/omap-serial.h>
+#define UART_BUILD_REVISION(x, y) (((x)<< 8) | (y))
+
+#define OMAP_UART_REV_42 0x0402
+#define OMAP_UART_REV_46 0x0406
+#define OMAP_UART_REV_52 0x0502
+#define OMAP_UART_REV_63 0x0603
+
#define DEFAULT_CLK_SPEED 48000000 /* 48Mhz*/
/* SCR register bitmasks */
@@ -1346,6 +1353,58 @@ static void uart_tx_dma_callback(int lch, u16
ch_status, void *data)
return;
}
+static void omap_serial_fill_features_erratas(struct uart_omap_port *up)
+{
+ u32 mvr, scheme;
+ u16 revision, major, minor;
+
+ mvr = serial_in(up, UART_OMAP_MVER);
+
+ /* Check revision register scheme */
+ scheme = mvr& (0x03<< 30);
+ scheme>>= 30;
Minor nit-pick, why not ...
scheme = mvr>> 30;
yes will correct it.
Thinking some more, could be better to add some #defines for
OMAP_MVR_VERSION_MASK/SHIFT here.
+ switch (scheme) {
+ case 0: /* Legacy Scheme: OMAP2/3 */
+ /* MINOR_REV[0:4], MAJOR_REV[4:7] */
This scheme is also true from OMAP1 devices. Maybe we could include in the
comment.
No omap1 from $SUBJECT also reason,
mach-omap1/serial.c => 8250.c
mach-omap2/serial.c => omap-serial.c
Got it! Thanks.
+ major = (mvr& 0xf0)>> 4;
+ minor = (mvr& 0x0f);
+ break;
+ case 1:
+ /* New Scheme: OMAP4+ */
+ /* MINOR_REV[0:5], MAJOR_REV[8:10] */
+ major = (mvr& 0x7<< 8)>> 8;
Nit-pick ...
major = (mvr>> 8)& 0x7;
yes fine will correct this.
May be we should add #defines here to for OMAP_UART_MVR1_MAJ_MASK/SHIFT,
OMAP_UART_MVR1_MIN_MASK/SHIFT, OMAP_UART_MVR2_MAJ_MASK/SHIFT and
OMAP_UART_MVR2_MIN_MASK/SHIFT.
Jon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
