On Wednesday 29 February 2012 07:56 PM, Tero Kristo wrote:
From: Vishwanath BS<vishwanath.bs@xxxxxx>
Since IO Daisychain modifies only PRM registers, it makes sense to move
it to PRM File.
Signed-off-by: Vishwanath BS<vishwanath.bs@xxxxxx>
Tested-by: Govindraj.R<govindraj.raja@xxxxxx>
Signed-off-by: Tero Kristo<t-kristo@xxxxxx>
---
arch/arm/mach-omap2/pm34xx.c | 30 +-----------------------------
arch/arm/mach-omap2/prm2xxx_3xxx.c | 32 ++++++++++++++++++++++++++++++++
arch/arm/mach-omap2/prm2xxx_3xxx.h | 14 ++++++++++++++
3 files changed, 47 insertions(+), 29 deletions(-)
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index b0821a8..e97ec3f 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -85,34 +85,6 @@ static inline void omap3_per_restore_context(void)
omap_gpio_restore_context();
}
-static void omap3_enable_io_chain(void)
-{
- int timeout = 0;
-
- omap2_prm_set_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD,
- PM_WKEN);
- /* Do a readback to assure write has been done */
- omap2_prm_read_mod_reg(WKUP_MOD, PM_WKEN);
-
- while (!(omap2_prm_read_mod_reg(WKUP_MOD, PM_WKST)&
- OMAP3430_ST_IO_CHAIN_MASK)) {
- timeout++;
- if (timeout> 1000) {
- pr_err("Wake up daisy chain activation failed.\n");
- return;
- }
- }
- omap2_prm_clear_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD,
- PM_WKEN);
-
-}
-
-static void omap3_disable_io_chain(void)
-{
- omap2_prm_clear_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD,
- PM_WKEN);
-}
-
static void omap3_core_save_context(void)
{
omap3_ctrl_save_padconf();
@@ -324,7 +296,7 @@ void omap_sram_idle(void)
core_next_state< PWRDM_POWER_ON)) {
omap2_prm_set_mod_reg_bits(OMAP3430_EN_IO_MASK, WKUP_MOD, PM_WKEN);
if (omap3_has_io_chain_ctrl())
- omap3_enable_io_chain();
+ omap3_trigger_io_chain();
}
pwrdm_pre_transition();
diff --git a/arch/arm/mach-omap2/prm2xxx_3xxx.c b/arch/arm/mach-omap2/prm2xxx_3xxx.c
index 9ce7654..fc98781 100644
--- a/arch/arm/mach-omap2/prm2xxx_3xxx.c
+++ b/arch/arm/mach-omap2/prm2xxx_3xxx.c
@@ -301,6 +301,38 @@ void omap3xxx_prm_restore_irqen(u32 *saved_mask)
OMAP3_PRM_IRQENABLE_MPU_OFFSET);
}
+/**
+ * Maximum time(us) it takes to output the signal WUCLKOUT of the last pad of
+ * the I/O ring after asserting WUCLKIN high
+ */
+#define MAX_IOPAD_LATCH_TIME 1000
Since we are changing the implementation to use omap_test_timeout()
in this patch, it makes sense to make this 100 so we have a max 100us
delay, similar to what we did on OMAP4.
+
+/* OMAP3 Daisychain enable sequence */
+void omap3_trigger_io_chain(void)
+{
+ int i = 0;
+
+ omap2_prm_set_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD,
+ PM_WKEN);
+ /* Do a readback to assure write has been done */
+ omap2_prm_read_mod_reg(WKUP_MOD, PM_WKEN);
+
+ omap_test_timeout(((omap2_prm_read_mod_reg(WKUP_MOD, PM_WKST)&
+ OMAP3430_ST_IO_CHAIN_MASK) == 1),
+ MAX_IOPAD_LATCH_TIME, i);
+
+ omap2_prm_clear_mod_reg_bits(OMAP3430_EN_IO_CHAIN_MASK, WKUP_MOD,
+ PM_WKEN);
The comment from Djamil should hold good here too. We should wait for
IO chain status to show 0 here.
+}
+
regards,
Rajendra
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
