On Saturday 05 November 2011 01:34 AM, Olof Johansson wrote:
On Fri, Nov 04, 2011 at 05:20:39PM +0530, Rajendra Nayak wrote:
Define dt bindings for the ti-omap-hsmmc, and adapt
the driver to extract data (which was earlier passed as
platform_data) from device tree node.
Signed-off-by: Rajendra Nayak<rnayak@xxxxxx>
---
.../devicetree/bindings/mmc/ti-omap-hsmmc.txt | 50 +++++++++
drivers/mmc/host/omap_hsmmc.c | 117 ++++++++++++++++++++
2 files changed, 167 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
new file mode 100644
index 0000000..370af1b
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
@@ -0,0 +1,50 @@
+* TI Highspeed MMC host controller for OMAP
+
+The Highspeed MMC Host Controller on TI OMAP family
+provides an interface for MMC, SD, and SDIO types of memory cards.
+
+Required properties:
+- compatible: Should be "ti,omap-hsmmc<n>", "ti,omap2-hsmmc";
+n is controller instance starting 0, for OMAP2/3 controllers
No, no, no. You should not have to specify the unit-address in the compatible
field. They are all programmed the same way, right?
Also, they should go from the specific to the generic, but the first property
is the same for 2/3 and 4. That's wrong.
agreed, will get rid of instance number from the compatible property.
+- compatible: Should be "ti,omap-hsmmc<n>", "ti,omap4-hsmmc";
+n is controller instance starting 0, for OMAP4 controllers
+- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1
I didn't think hwmod bindings were settled on yet?
+- reg : should contain hsmmc registers location and length
+
+Optional properties:
+ti,hsmmc-supports-dual-volt: boolean, supports dual voltage cards
ti,dual-voltage is a better name here (by definition, if it has the property it
supports it, the word "supports" is redundant).
Ok.
+ti,hsmmc-nr-slots: Number of mmc slots
You shouldn't have to specify this, it can be derived from the number of child
nodes.
right, will do that.
+<supply-name>-supply: phandle to the regulator device tree node
+"supply-name" examples are "vmmc", "vmmc_aux" etc
+ti,hsmmc-has-pbias: Has PBIAS cell support
+ti,hsmmc-has-special-reset: Requires a special softreset sequence
you can drop hsmmc- from the properties here
Ok.
+
+For every supported slot a slot node can be defined
+with the following optional properties
+
+ti,hsmmc-slot-name: Name assocaited to the mmc slot
+ti,hsmmc-gpio-cd: gpio for card detect
+ti,hsmmc-gpio-wp: gpio for write protect
Please use the same standard as the other mmc controllers for CD/WP.
Ok.
+ti,hsmmc-ocr-mask: mmc/sd/sdio ocr mask
What is OCR mask?
Its used to derive the vdd range the card supports. I hadn't
looked at this closely, but looks like this isn't something that
needs to be told to the driver anyway, it can always just query the
card about the voltages it supports and derive the ocrmask internally.
One more of the hacks in the driver to be cleaned up. Will drop this
property completely.
+ti,hsmmc-non-removable: non-removable slot (like eMMC)
Same here, non-removable should be standardized.
You mean there is already a binding available for this?
Thanks for the review.
regards,
Rajendra
-Olof
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
