The helper routine is meant to be used by regulator drivers
to extract the regulator_init_data structure passed from device tree.
'consumer_supplies' which is part of regulator_init_data is not extracted
as the regulator consumer mappings are passed through DT differently,
implemented in subsequent patches.
Also add documentation for regulator bindings to be used to pass
regulator_init_data struct information from device tree.
Signed-off-by: Rajendra Nayak <rnayak@xxxxxx>
---
.../devicetree/bindings/regulator/regulator.txt | 37 +++++++++
drivers/of/Kconfig | 6 ++
drivers/of/Makefile | 1 +
drivers/of/of_regulator.c | 85 ++++++++++++++++++++
include/linux/of_regulator.h | 23 +++++
5 files changed, 152 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/regulator/regulator.txt
create mode 100644 drivers/of/of_regulator.c
create mode 100644 include/linux/of_regulator.h
diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
new file mode 100644
index 0000000..001e5ce
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -0,0 +1,37 @@
+Voltage/Current Regulators
+
+Required properties:
+- compatible: Must be "regulator";
+
+Optional properties:
+- supply-regulator: Name of the parent regulator
+- min-uV: smallest voltage consumers may set
+- max-uV: largest voltage consumers may set
+- uV-offset: Offset applied to voltages from consumer to compensate for voltage drops
+- min-uA: smallest current consumers may set
+- max-uA: largest current consumers may set
+- mode-fast: boolean, Can handle fast changes in its load
+- mode-normal: boolean, Normal regulator power supply mode
+- mode-idle: boolean, Can be more efficient during light loads
+- mode-standby: boolean, Can be most efficient during light loads
+- change-voltage: boolean, Output voltage can be changed by software
+- change-current: boolean, Output current can be chnaged by software
+- change-mode: boolean, Operating mode can be changed by software
+- change-status: boolean, Enable/Disable control for regulator exists
+- change-drms: boolean, Dynamic regulator mode switching is enabled
+- input-uV: Input voltage for regulator when supplied by another regulator
+- initial-mode: Mode to set at startup
+- always-on: boolean, regulator should never be disabled
+- boot-on: bootloader/firmware enabled regulator
+- apply-uV: apply uV constraint if min == max
+
+Example:
+
+ xyz-regulator: regulator@0 {
+ compatible = "regulator";
+ min-uV = <1000000>;
+ max-uV = <2500000>;
+ mode-fast;
+ change-voltage;
+ always-on;
+ };
diff --git a/drivers/of/Kconfig b/drivers/of/Kconfig
index b3bfea5..296b96d 100644
--- a/drivers/of/Kconfig
+++ b/drivers/of/Kconfig
@@ -87,4 +87,10 @@ config OF_PCI_IRQ
help
OpenFirmware PCI IRQ routing helpers
+config OF_REGULATOR
+ def_bool y
+ depends on REGULATOR
+ help
+ OpenFirmware regulator framework helpers
+
endmenu # OF
diff --git a/drivers/of/Makefile b/drivers/of/Makefile
index 74b959c..bea2852 100644
--- a/drivers/of/Makefile
+++ b/drivers/of/Makefile
@@ -12,3 +12,4 @@ obj-$(CONFIG_OF_SPI) += of_spi.o
obj-$(CONFIG_OF_MDIO) += of_mdio.o
obj-$(CONFIG_OF_PCI) += of_pci.o
obj-$(CONFIG_OF_PCI_IRQ) += of_pci_irq.o
+obj-$(CONFIG_OF_REGULATOR) += of_regulator.o
diff --git a/drivers/of/of_regulator.c b/drivers/of/of_regulator.c
new file mode 100644
index 0000000..f01d275
--- /dev/null
+++ b/drivers/of/of_regulator.c
@@ -0,0 +1,85 @@
+/*
+ * OF helpers for regulator framework
+ *
+ * Copyright (C) 2011 Texas Instruments, Inc.
+ * Rajendra Nayak <rnayak@xxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/regulator/machine.h>
+
+static void of_get_regulation_constraints(struct device_node *np,
+ struct regulator_init_data **init_data)
+{
+ unsigned int valid_modes_mask = 0, valid_ops_mask = 0;
+
+ of_property_read_u32(np, "min-uV", &(*init_data)->constraints.min_uV);
+ of_property_read_u32(np, "max-uV", &(*init_data)->constraints.max_uV);
+ of_property_read_u32(np, "uV-offset", &(*init_data)->constraints.uV_offset);
+ of_property_read_u32(np, "min-uA", &(*init_data)->constraints.min_uA);
+ of_property_read_u32(np, "max-uA", &(*init_data)->constraints.max_uA);
+
+ /* valid modes mask */
+ if (of_find_property(np, "mode-fast", NULL))
+ valid_modes_mask |= REGULATOR_MODE_FAST;
+ if (of_find_property(np, "mode-normal", NULL))
+ valid_modes_mask |= REGULATOR_MODE_NORMAL;
+ if (of_find_property(np, "mode-idle", NULL))
+ valid_modes_mask |= REGULATOR_MODE_IDLE;
+ if (of_find_property(np, "mode-standby", NULL))
+ valid_modes_mask |= REGULATOR_MODE_STANDBY;
+
+ /* valid ops mask */
+ if (of_find_property(np, "change-voltage", NULL))
+ valid_ops_mask |= REGULATOR_CHANGE_VOLTAGE;
+ if (of_find_property(np, "change-current", NULL))
+ valid_ops_mask |= REGULATOR_CHANGE_CURRENT;
+ if (of_find_property(np, "change-mode", NULL))
+ valid_ops_mask |= REGULATOR_CHANGE_MODE;
+ if (of_find_property(np, "change-status", NULL))
+ valid_ops_mask |= REGULATOR_CHANGE_STATUS;
+
+ (*init_data)->constraints.valid_modes_mask = valid_modes_mask;
+ (*init_data)->constraints.valid_ops_mask = valid_ops_mask;
+
+ of_property_read_u32(np, "input-uV",
+ &(*init_data)->constraints.input_uV);
+ of_property_read_u32(np, "initial-mode",
+ &(*init_data)->constraints.initial_mode);
+
+ if (of_find_property(np, "always-on", NULL))
+ (*init_data)->constraints.always_on = true;
+ if (of_find_property(np, "boot-on", NULL))
+ (*init_data)->constraints.boot_on = true;
+ if (of_find_property(np, "apply-uV", NULL))
+ (*init_data)->constraints.apply_uV = true;
+}
+
+/**
+ * of_get_regulator_init_data - extarct regulator_init_data structure info
+ * @np: Pointer to regulator device tree node
+ *
+ * Populates regulator_init_data structure by extracting data from device
+ * tree node, returns a pointer to the populated struture or NULL if memory
+ * alloc fails.
+ */
+struct regulator_init_data *of_get_regulator_init_data(struct device_node *np)
+{
+ struct regulator_init_data *init_data;
+
+ init_data = kzalloc(sizeof(struct regulator_init_data), GFP_KERNEL);
+ if (!init_data)
+ return NULL; /* Out of memory? */
+
+ init_data->supply_regulator = (char *)of_get_property(np,
+ "supply-regulator", NULL);
+ of_get_regulation_constraints(np, &init_data);
+ return init_data;
+}
+EXPORT_SYMBOL(of_get_regulator_init_data);
diff --git a/include/linux/of_regulator.h b/include/linux/of_regulator.h
new file mode 100644
index 0000000..5eb048c
--- /dev/null
+++ b/include/linux/of_regulator.h
@@ -0,0 +1,23 @@
+/*
+ * OpenFirmware regulator support routines
+ *
+ */
+
+#ifndef __LINUX_OF_REG_H
+#define __LINUX_OF_REG_H
+
+#include <linux/regulator/machine.h>
+
+#if defined(CONFIG_OF_REGULATOR)
+extern struct regulator_init_data
+ *of_get_regulator_init_data(struct device_node *np);
+#else
+static inline struct regulator_init_data
+ *of_get_regulator_init_data(struct device_node *np)
+{
+ return NULL;
+}
+#endif /* CONFIG_OF_REGULATOR */
+
+#endif /* __LINUX_OF_REG_H */
+
--
1.7.1
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
