Tony, Does this one look better? On 06/15/11 00:16, Igor Grinberg wrote: > cm-t3730 is basically the same board as cm-t35, > but has AM/DM3730 SoC assembled and therefore some changes are required. > > Signed-off-by: Igor Grinberg <grinberg@xxxxxxxxxxxxxx> > Acked-by: Mike Rapoport <mike@xxxxxxxxxxxxxx> > --- > v3: fix MACH_* selection > remove completely the use of cpu_is_* > v2: Add debug uart entry > > > arch/arm/mach-omap2/Kconfig | 6 ++- > arch/arm/mach-omap2/board-cm-t35.c | 77 ++++++++++++++++++++----- > arch/arm/plat-omap/include/plat/uncompress.h | 1 + > 3 files changed, 67 insertions(+), 17 deletions(-) > > diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig > index 19d5891..4ae6257 100644 > --- a/arch/arm/mach-omap2/Kconfig > +++ b/arch/arm/mach-omap2/Kconfig > @@ -266,9 +266,10 @@ config MACH_OMAP_ZOOM3 > select REGULATOR_FIXED_VOLTAGE > > config MACH_CM_T35 > - bool "CompuLab CM-T35 module" > + bool "CompuLab CM-T35/CM-T3730 modules" > depends on ARCH_OMAP3 > default y > + select MACH_CM_T3730 > select OMAP_PACKAGE_CUS > > config MACH_CM_T3517 > @@ -277,6 +278,9 @@ config MACH_CM_T3517 > default y > select OMAP_PACKAGE_CBB > > +config MACH_CM_T3730 > + bool > + > config MACH_IGEP0020 > bool "IGEP v2 board" > depends on ARCH_OMAP3 > diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c > index 256b81c..ea31281 100644 > --- a/arch/arm/mach-omap2/board-cm-t35.c > +++ b/arch/arm/mach-omap2/board-cm-t35.c > @@ -1,5 +1,5 @@ > /* > - * board-cm-t35.c (CompuLab CM-T35 module) > + * CompuLab CM-T35/CM-T3730 modules support > * > * Copyright (C) 2009-2011 CompuLab, Ltd. > * Authors: Mike Rapoport <mike@xxxxxxxxxxxxxx> > @@ -574,17 +574,11 @@ static struct omap_board_mux board_mux[] __initdata = { > OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT), > > - /* DSS */ > + /* common DSS */ > OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > @@ -597,12 +591,6 @@ static struct omap_board_mux board_mux[] __initdata = { > OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA18, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA19, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA20, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA21, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA22, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > - OMAP3_MUX(DSS_DATA23, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT), > > /* display controls */ > OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT), > @@ -615,19 +603,53 @@ static struct omap_board_mux board_mux[] __initdata = { > > { .reg_offset = OMAP_MUX_TERMINATOR }, > }; > + > +static void __init cm_t3x_common_dss_mux_init(int mux_mode) > +{ > + omap_mux_init_signal("dss_data18", mux_mode); > + omap_mux_init_signal("dss_data19", mux_mode); > + omap_mux_init_signal("dss_data20", mux_mode); > + omap_mux_init_signal("dss_data21", mux_mode); > + omap_mux_init_signal("dss_data22", mux_mode); > + omap_mux_init_signal("dss_data23", mux_mode); > +} > + > +static void __init cm_t35_init_mux(void) > +{ > + omap_mux_init_signal("gpio_70", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT); > + omap_mux_init_signal("gpio_71", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT); > + omap_mux_init_signal("gpio_72", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT); > + omap_mux_init_signal("gpio_73", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT); > + omap_mux_init_signal("gpio_74", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT); > + omap_mux_init_signal("gpio_75", OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT); > + cm_t3x_common_dss_mux_init(OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT); > +} > + > +static void __init cm_t3730_init_mux(void) > +{ > + omap_mux_init_signal("sys_boot0", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT); > + omap_mux_init_signal("sys_boot1", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT); > + omap_mux_init_signal("sys_boot3", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT); > + omap_mux_init_signal("sys_boot4", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT); > + omap_mux_init_signal("sys_boot5", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT); > + omap_mux_init_signal("sys_boot6", OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT); > + cm_t3x_common_dss_mux_init(OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT); > +} > +#else > +static inline void cm_t35_init_mux(void) {} > +static inline void cm_t3730_init_mux(void) {} > #endif > > static struct omap_board_config_kernel cm_t35_config[] __initdata = { > }; > > -static void __init cm_t35_init(void) > +static void __init cm_t3x_common_init(void) > { > omap_board_config = cm_t35_config; > omap_board_config_size = ARRAY_SIZE(cm_t35_config); > omap3_mux_init(board_mux, OMAP_PACKAGE_CUS); > omap_serial_init(); > cm_t35_init_i2c(); > - cm_t35_init_nand(); > omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL); > cm_t35_init_ethernet(); > cm_t35_init_led(); > @@ -637,6 +659,19 @@ static void __init cm_t35_init(void) > usbhs_init(&usbhs_bdata); > } > > +static void __init cm_t35_init(void) > +{ > + cm_t3x_common_init(); > + cm_t35_init_mux(); > + cm_t35_init_nand(); > +} > + > +static void __init cm_t3730_init(void) > +{ > + cm_t3x_common_init(); > + cm_t3730_init_mux(); > +} > + > MACHINE_START(CM_T35, "Compulab CM-T35") > .boot_params = 0x80000100, > .reserve = omap_reserve, > @@ -646,3 +681,13 @@ MACHINE_START(CM_T35, "Compulab CM-T35") > .init_machine = cm_t35_init, > .timer = &omap_timer, > MACHINE_END > + > +MACHINE_START(CM_T3730, "Compulab CM-T3730") > + .boot_params = 0x80000100, > + .reserve = omap_reserve, > + .map_io = omap3_map_io, > + .init_early = cm_t35_init_early, > + .init_irq = omap_init_irq, > + .init_machine = cm_t3730_init, > + .timer = &omap_timer, > +MACHINE_END > diff --git a/arch/arm/plat-omap/include/plat/uncompress.h b/arch/arm/plat-omap/include/plat/uncompress.h > index ac4b60d..a067484 100644 > --- a/arch/arm/plat-omap/include/plat/uncompress.h > +++ b/arch/arm/plat-omap/include/plat/uncompress.h > @@ -148,6 +148,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id) > /* omap3 based boards using UART3 */ > DEBUG_LL_OMAP3(3, cm_t35); > DEBUG_LL_OMAP3(3, cm_t3517); > + DEBUG_LL_OMAP3(3, cm_t3730); > DEBUG_LL_OMAP3(3, craneboard); > DEBUG_LL_OMAP3(3, devkit8000); > DEBUG_LL_OMAP3(3, igep0020); -- Regards, Igor. -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html