The USB enable GPIO has been in beagleboard xM revision C
The USER button has been moved since beagleboard xM
Also, board specific initialization has been moved to beagle_config struct
and initialized in omap3_beagle_init_rev. Default values in struct are for xMC.
Signed-off-by: Joel A Fernandes <joelagnel@xxxxxx>
Signed-off-by: Koen Kooi <koen@xxxxxxxxxxxxxxxxxxxxx>
---
arch/arm/mach-omap2/board-omap3beagle.c | 70 ++++++++++++++++++++-----------
1 files changed, 46 insertions(+), 24 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c
b/arch/arm/mach-omap2/board-omap3beagle.c
index 7f21d24..261fb53 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -61,7 +61,8 @@
* AXBX = GPIO173, GPIO172, GPIO171: 1 1 1
* C1_3 = GPIO173, GPIO172, GPIO171: 1 1 0
* C4 = GPIO173, GPIO172, GPIO171: 1 0 1
- * XM = GPIO173, GPIO172, GPIO171: 0 0 0
+ * XMA/XMB = GPIO173, GPIO172, GPIO171: 0 0 0
+ * XMC = GPIO173, GPIO172, GPIO171: 0 1 0
*/
enum {
OMAP3BEAGLE_BOARD_UNKN = 0,
@@ -69,14 +70,26 @@ enum {
OMAP3BEAGLE_BOARD_C1_3,
OMAP3BEAGLE_BOARD_C4,
OMAP3BEAGLE_BOARD_XM,
+ OMAP3BEAGLE_BOARD_XMC,
};
static u8 omap3_beagle_version;
-static u8 omap3_beagle_get_rev(void)
-{
- return omap3_beagle_version;
-}
+/*
+ * Board-specific configuration
+ * Defaults to BeagleBoard-xMC
+ */
+static struct {
+ int mmc1_gpio_wp;
+ int usb_pwr_level;
+ int reset_gpio;
+ int usr_button_gpio;
+} beagle_config = {
+ .mmc1_gpio_wp = -EINVAL,
+ .usb_pwr_level = GPIOF_OUT_INIT_LOW,
+ .reset_gpio = 129,
+ .usr_button_gpio = 4,
+};
static struct gpio omap3_beagle_rev_gpios[] __initdata = {
{ 171, GPIOF_IN, "rev_id_0" },
@@ -111,18 +124,32 @@ static void __init omap3_beagle_init_rev(void)
case 7:
printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
+ beagle_config.mmc1_gpio_wp = 29;
+ beagle_config.reset_gpio = 170;
+ beagle_config.usr_button_gpio = 7;
break;
case 6:
printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
+ beagle_config.mmc1_gpio_wp = 23;
+ beagle_config.reset_gpio = 170;
+ beagle_config.usr_button_gpio = 7;
break;
case 5:
printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
+ beagle_config.mmc1_gpio_wp = 23;
+ beagle_config.reset_gpio = 170;
+ beagle_config.usr_button_gpio = 7;
break;
case 0:
printk(KERN_INFO "OMAP3 Beagle Rev: xM\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
+ beagle_config.usb_pwr_level = GPIOF_OUT_INIT_HIGH;
+ break;
+ case 2:
+ printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n");
+ omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC;
break;
default:
printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
@@ -234,7 +261,7 @@ static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
.caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
- .gpio_wp = 29,
+ .gpio_wp = -EINVAL,
},
{} /* Terminator */
};
@@ -252,17 +279,11 @@ static struct gpio_led gpio_leds[];
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
- int r, usb_pwr_level;
-
- if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
- mmc[0].gpio_wp = -EINVAL;
- } else if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
- (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C4)) {
- omap_mux_init_gpio(23, OMAP_PIN_INPUT);
- mmc[0].gpio_wp = 23;
- } else {
- omap_mux_init_gpio(29, OMAP_PIN_INPUT);
- }
+ int r;
+
+ if (beagle_config.mmc1_gpio_wp != -EINVAL)
+ omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
+ mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp;
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
mmc[0].gpio_cd = gpio + 0;
omap2_hsmmc_init(mmc);
@@ -276,9 +297,7 @@ static int beagle_twl_gpio_setup(struct device *dev,
* high / others active low)
* DVI reset GPIO is different between beagle revisions
*/
- if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
- usb_pwr_level = GPIOF_OUT_INIT_HIGH;
- beagle_dvi_device.reset_gpio = 129;
+ if (cpu_is_omap3630()) {
/*
* gpio + 1 on Xm controls the TFP410's enable line (active low)
* gpio + 2 control varies depending on the board rev as below:
@@ -296,8 +315,6 @@ static int beagle_twl_gpio_setup(struct device *dev,
pr_err("%s: unable to configure DVI_LDO_EN\n",
__func__);
} else {
- usb_pwr_level = GPIOF_OUT_INIT_LOW;
- beagle_dvi_device.reset_gpio = 170;
/*
* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
@@ -305,8 +322,10 @@ static int beagle_twl_gpio_setup(struct device *dev,
if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
pr_err("%s: unable to configure EHCI_nOC\n", __func__);
}
+ beagle_dvi_device.reset_gpio = beagle_config.reset_gpio;
- gpio_request_one(gpio + TWL4030_GPIO_MAX, usb_pwr_level, "nEN_USB_PWR");
+ gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
+ "nEN_USB_PWR");
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
@@ -526,7 +545,7 @@ static void __init beagle_opp_init(void)
}
/* Custom OPP enabled for XM */
- if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
+ if (cpu_is_omap3630()) {
struct omap_hwmod *mh = omap_hwmod_lookup("mpu");
struct omap_hwmod *dh = omap_hwmod_lookup("iva");
struct device *dev;
@@ -566,6 +585,9 @@ static void __init omap3_beagle_init(void)
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_beagle_init_rev();
omap3_beagle_i2c_init();
+
+ gpio_buttons[0].gpio = beagle_config.usr_button_gpio;
+
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
omap_display_init(&beagle_dss_data);
--
1.6.1
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
