> -----Original Message-----
> From: Valkeinen, Tomi
> Sent: Monday, May 16, 2011 2:23 PM
> To: Igor Grinberg
> Cc: Janorkar, Mayuresh; tony@xxxxxxxxxxx; linux-omap@xxxxxxxxxxxxxxx;
> Stanley Miao
> Subject: Re: [PATCH 4/6] OMAP: LDP: Port the display driver to new DSS2
>
> On Thu, 2011-05-12 at 09:40 +0300, Igor Grinberg wrote:
> >
> > On 05/11/11 09:32, Tomi Valkeinen wrote:
> >
> > > On Wed, 2011-05-11 at 10:28 +0530, Janorkar, Mayuresh wrote:
> > >
> > >>> +static void __init ldp_display_init(void)
> > >>> +{
> > >>> + int r;
> > >>> +
> > >>> + struct gpio gpios[] = {
> > >>> + {LCD_PANEL_RESET_GPIO, GPIOF_OUT_INIT_HIGH, "LCD
> RESET"},
> > >>> + {LCD_PANEL_QVGA_GPIO, GPIOF_OUT_INIT_HIGH, "LCD QVGA"},
> > >>> + {LCD_PANEL_ENABLE_GPIO, GPIOF_OUT_INIT_LOW, "LCD
> ENABLE"},
> > >>> + {LCD_PANEL_BACKLIGHT_GPIO, GPIOF_OUT_INIT_LOW, "LCD
> > >>> BACKLIGHT"},
> > >>> + };
> > >>> +
> > >>> + r = gpio_request_array(gpios, ARRAY_SIZE(gpios));
> > >>> + if (r) {
> > >>> + pr_err("Cannot request LCD GPIOs, error %d\n", r);
> > >>> + return;
> > >>> + }
> > >> If I test with this patch, this request is returning error.
> > > Hmm. Well, the GPIOs are the same as in the old driver. However, the
> old
> > > driver doesn't even seem to check if it manages to request the GPIOs,
> so
> > > it may well be that it was failing also.
> > >
> > > Can you check from /sys/class/gpio/ if some of the GPIOs are already
> > > allocated: 207, 199, 55, 56?
> > >
> > > The definition of two of those GPIOs look kinda funny to me: (15 +
> > > OMAP_MAX_GPIO_LINES). I don't know what OMAP_MAX_GPIO_LINES means, but
> > > it sure doesn't sound ok to have a GPIO number that is 15 over the
> > > maximum =).
> > >
> >
> > This means that some kind of gpio expander is used.
> > I bet those are twl gpios (or may be some other discrete chip).
> > If those are twl gpios then you need to provide the .setup callback
> > in struct twl4030_gpio_platform_data which will request and setup those
> gpios.
>
> Here's an updated patch with the twl gpio code.
>
> All the old omapfb porting patches, including new drivers for DSS2, can
> be found from
>
> git://gitorious.org/linux-omap-dss2/linux.git old-omapfb-port
>
> Tomi
>
> diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-
> ldp.c
> index e2ba779..ed78b9a 100644
> --- a/arch/arm/mach-omap2/board-ldp.c
> +++ b/arch/arm/mach-omap2/board-ldp.c
> @@ -44,6 +44,9 @@
> #include <asm/delay.h>
> #include <plat/usb.h>
>
> +#include <video/omapdss.h>
> +#include <video/omap-panel-generic-dpi.h>
> +
> #include "board-flash.h"
> #include "mux.h"
> #include "hsmmc.h"
> @@ -275,19 +278,70 @@ static inline void __init ldp_init_smsc911x(void)
> gpio_direction_input(eth_gpio);
> }
>
> -static struct platform_device ldp_lcd_device = {
> - .name = "ldp_lcd",
> - .id = -1,
> +/* LCD */
> +
> +static int ldp_backlight_gpio;
> +static int ldp_lcd_enable_gpio;
> +
> +#define LCD_PANEL_RESET_GPIO 55
> +#define LCD_PANEL_QVGA_GPIO 56
> +
> +static int ldp_panel_enable_lcd(struct omap_dss_device *dssdev)
> +{
> + gpio_direction_output(ldp_lcd_enable_gpio, 1);
> + gpio_direction_output(ldp_backlight_gpio, 1);
> +
> + return 0;
> +}
> +
> +static void ldp_panel_disable_lcd(struct omap_dss_device *dssdev)
> +{
> + gpio_direction_output(ldp_lcd_enable_gpio, 0);
> + gpio_direction_output(ldp_backlight_gpio, 0);
> +}
> +
> +static struct panel_generic_dpi_data ldp_panel_data = {
> + .name = "2430sdp",
> + .platform_enable = ldp_panel_enable_lcd,
> + .platform_disable = ldp_panel_disable_lcd,
> +};
> +
> +static struct omap_dss_device ldp_lcd_device = {
> + .name = "lcd",
> + .driver_name = "generic_dpi_panel",
> + .type = OMAP_DISPLAY_TYPE_DPI,
> + .phy.dpi.data_lines = 16,
>From a working DSS code at:
http://lxr.linux.no/#linux+v2.6.38/drivers/video/omap/lcd_ldp.c
.data_lines should be 18
> + .data = &ldp_panel_data,
> };
>
> -static struct omap_lcd_config ldp_lcd_config __initdata = {
> - .ctrl_name = "internal",
> +static struct omap_dss_device *ldp_dss_devices[] = {
> + &ldp_lcd_device,
> };
>
> -static struct omap_board_config_kernel ldp_config[] __initdata = {
> - { OMAP_TAG_LCD, &ldp_lcd_config },
> +static struct omap_dss_board_info ldp_dss_data = {
> + .num_devices = ARRAY_SIZE(ldp_dss_devices),
> + .devices = ldp_dss_devices,
> + .default_device = &ldp_lcd_device,
> };
>
> +static void __init ldp_display_init(void)
> +{
> + int r;
> +
> + static struct gpio gpios[] __initdata = {
> + {LCD_PANEL_RESET_GPIO, GPIOF_OUT_INIT_HIGH, "LCD RESET"},
> + {LCD_PANEL_QVGA_GPIO, GPIOF_OUT_INIT_HIGH, "LCD QVGA"},
> + };
> +
> + r = gpio_request_array(gpios, ARRAY_SIZE(gpios));
> + if (r) {
> + pr_err("Cannot request LCD GPIOs, error %d\n", r);
> + return;
> + }
> +
> + omap_display_init(&ldp_dss_data);
> +}
> +
> static void __init omap_ldp_init_early(void)
> {
> omap2_init_common_infrastructure();
> @@ -298,10 +352,30 @@ static struct twl4030_usb_data ldp_usb_data = {
> .usb_mode = T2_USB_MODE_ULPI,
> };
>
> +static int ldp_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned
> ngpio)
> +{
> + int r;
> +
> + struct gpio gpios[] = {
> + {gpio + 7 , GPIOF_OUT_INIT_LOW, "LCD ENABLE"},
> + {gpio + 15, GPIOF_OUT_INIT_LOW, "LCD BACKLIGHT"},
> + };
> +
> + r = gpio_request_array(gpios, ARRAY_SIZE(gpios));
> + if (r)
> + pr_err("Cannot request LCD GPIOs, error %d\n", r);
> +
> + ldp_backlight_gpio = gpio + 15;
> + ldp_lcd_enable_gpio = gpio + 7;
> +
> + return r;
> +}
> +
> static struct twl4030_gpio_platform_data ldp_gpio_data = {
> .gpio_base = OMAP_MAX_GPIO_LINES,
> .irq_base = TWL4030_GPIO_IRQ_BASE,
> .irq_end = TWL4030_GPIO_IRQ_END,
> + .setup = ldp_twl_gpio_setup,
> };
>
> static struct twl4030_madc_platform_data ldp_madc_data = {
> @@ -347,6 +421,26 @@ static struct regulator_init_data ldp_vaux1 = {
> .consumer_supplies = ldp_vaux1_supplies,
> };
>
> +static struct regulator_consumer_supply ldp_vpll2_supplies[] = {
> + REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
> + REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi1"),
> +};
> +
> +static struct regulator_init_data ldp_vpll2 = {
> + .constraints = {
> + .name = "VDVI",
> + .min_uV = 1800000,
> + .max_uV = 1800000,
> + .apply_uV = true,
> + .valid_modes_mask = REGULATOR_MODE_NORMAL
> + | REGULATOR_MODE_STANDBY,
> + .valid_ops_mask = REGULATOR_CHANGE_MODE
> + | REGULATOR_CHANGE_STATUS,
> + },
> + .num_consumer_supplies = ARRAY_SIZE(ldp_vpll2_supplies),
> + .consumer_supplies = ldp_vpll2_supplies,
> +};
> +
> static struct twl4030_platform_data ldp_twldata = {
> .irq_base = TWL4030_IRQ_BASE,
> .irq_end = TWL4030_IRQ_END,
> @@ -356,6 +450,7 @@ static struct twl4030_platform_data ldp_twldata = {
> .usb = &ldp_usb_data,
> .vmmc1 = &ldp_vmmc1,
> .vaux1 = &ldp_vaux1,
> + .vpll2 = &ldp_vpll2,
> .gpio = &ldp_gpio_data,
> .keypad = &ldp_kp_twl4030_data,
> };
> @@ -390,7 +485,6 @@ static struct omap2_hsmmc_info mmc[] __initdata = {
>
> static struct platform_device *ldp_devices[] __initdata = {
> &ldp_smsc911x_device,
> - &ldp_lcd_device,
> &ldp_gpio_keys_device,
> };
>
> @@ -441,8 +535,6 @@ static struct mtd_partition ldp_nand_partitions[] = {
> static void __init omap_ldp_init(void)
> {
> omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
> - omap_board_config = ldp_config;
> - omap_board_config_size = ARRAY_SIZE(ldp_config);
> ldp_init_smsc911x();
> omap_i2c_init();
> platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
> @@ -459,6 +551,8 @@ static void __init omap_ldp_init(void)
> omap2_hsmmc_init(mmc);
> /* link regulators to MMC adapters */
> ldp_vmmc1_supply.dev = mmc[0].dev;
> +
> + ldp_display_init();
> }
>
> MACHINE_START(OMAP_LDP, "OMAP LDP board")
>
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
