Shweta Gulati <shweta.gulati@xxxxxx> writes:
> From: Thara Gopinath <thara@xxxxxx>
>
> The smartreflex bit on twl4030 needs to be enabled by default irrespective
> of whether smartreflex module is enabled on the OMAP side or not.
> This is because without this bit enabled the voltage scaling through
> vp forceupdate does not function properly on OMAP3.API added
> 'omap3_twl_set_sr_bit' with parameter to set/clear SR bit. It is cleared
> for platforms where voltage is not scaled using vpforceupdate
> or vc_bypass Method. In those cases 'omap3_twl_set_sr_bit' is called
> from board file, to make sure this bit is not overwritten in
> 'omap3_twl_init', a flag 'twl_sr_enable'
> is added.
As Sanjeev pointed out, the use of 'irrespective' above is confusing, in
fact the whole changelog is kind of confusing.
The changelog states that it has to always be enabled, but then goes on
to describe the situation(s) where it would be disabled.
Here's my rephrasing of how I understand the above changelog
- enable: *always* be enabled
- enable: needed for VP force update
- disable: platforms using VP forced update or VP bypass
-ECONFUSED
Kevin
> This patch is based on LO PM Branch and Smartreflex has been
> tested on OMAP3430 SDP, OMAP3630 SDP and boot tested on
> OMAP2430 SDP.
>
> Signed-off-by: Thara Gopinath <thara@xxxxxx>
> Signed-off-by: Shweta Gulati <shweta.gulati@xxxxxx>
> ---
> arch/arm/mach-omap2/omap_twl.c | 62 ++++++++++++++++++++++++++++++++++++++++
> arch/arm/mach-omap2/pm.h | 1 +
> 2 files changed, 63 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/omap_twl.c b/arch/arm/mach-omap2/omap_twl.c
> index 00e1d2b..871a349 100644
> --- a/arch/arm/mach-omap2/omap_twl.c
> +++ b/arch/arm/mach-omap2/omap_twl.c
> @@ -59,8 +59,15 @@
>
> static bool is_offset_valid;
> static u8 smps_offset;
> +/*
> + * Flag to ensure Smartreflex bit in TWL
> + * being cleared in board file is not overwritten.
> + */
> +static bool twl_sr_enable = true;
>
> +#define TWL4030_DCDC_GLOBAL_CFG 0x06
> #define REG_SMPS_OFFSET 0xE0
> +#define SMARTREFLEX_ENABLE BIT(3)
>
> static unsigned long twl4030_vsel_to_uv(const u8 vsel)
> {
> @@ -269,6 +276,16 @@ int __init omap3_twl_init(void)
> omap3_core_volt_info.vp_vddmax = OMAP3630_VP2_VLIMITTO_VDDMAX;
> }
>
> + /*
> + * The smartreflex bit on twl4030 needs to be enabled by
> + * default irrespective of whether smartreflex module is
> + * enabled on the OMAP side or not. This is because without
> + * this bit enabled the voltage scaling through
> + * vp forceupdate does not function properly on OMAP3.
> + */
> + if (twl_sr_enable)
> + omap3_twl_set_sr_bit(1);
> +
> voltdm = omap_voltage_domain_lookup("mpu");
> omap_voltage_register_pmic(voltdm, &omap3_mpu_volt_info);
>
> @@ -277,3 +294,48 @@ int __init omap3_twl_init(void)
>
> return 0;
> }
> +
> +/**
> + * omap3_twl_set_sr_bit() - API to Set/Clear SR bit on TWL
> + * @flag: Flag to Set/Clear SR bit
> + *
> + * If flag is non zero, enables Smartreflex bit on TWL 4030
> + * to make sure voltage scaling through Vp forceupdate works.
> + * Else, the smartreflex bit on twl4030 is
> + * cleared as there are platforms which use
> + * OMAP3 and T2 but use Synchronized Scaling Hardware
> + * Strategy (ENABLE_VMODE=1) and Direct Strategy Software
> + * Scaling Mode (ENABLE_VMODE=0), for setting the voltages,
> + * in those scenarios this bit is to be cleared.
> + * API returns 0 on sucess, error is returned
> + * if I2C read/write fails.
> + */
> +
> +int omap3_twl_set_sr_bit(u8 flag)
> +{
> + u8 temp;
> + int ret;
> +
> + ret = twl_i2c_read_u8(TWL4030_MODULE_PM_RECEIVER, &temp,
> + TWL4030_DCDC_GLOBAL_CFG);
> + if (ret)
> + goto err;
> +
> + if (flag) {
> + temp |= SMARTREFLEX_ENABLE;
> + twl_sr_enable = true;
> + } else {
> + temp &= ~SMARTREFLEX_ENABLE;
> + twl_sr_enable = false;
> + }
> +
> + ret = twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, temp,
> + TWL4030_DCDC_GLOBAL_CFG);
> + if (ret) {
> +err:
> + pr_err("%s: Unable to Read/Write to TWL4030 through I2C bus "
> + "\n", __func__);
> + return -EINVAL;
> + }
> + return 0;
> +}
> diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h
> index 704766b..c98be66 100644
> --- a/arch/arm/mach-omap2/pm.h
> +++ b/arch/arm/mach-omap2/pm.h
> @@ -127,6 +127,7 @@ static inline void omap_enable_smartreflex_on_init(void) {}
> #ifdef CONFIG_TWL4030_CORE
> extern int omap3_twl_init(void);
> extern int omap4_twl_init(void);
> +extern int omap3_twl_set_sr_bit(u8 flag);
> #else
> static inline int omap3_twl_init(void)
> {
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
