With addition of hwmod support to gpio, the ethernet controller goes undetected for OMAP35xEVM. So explicitly assert the reset signal to ethernet controller smsc911x - - GPIO7 (>=RevG version of EVM's) - GPIO64 (<=RevD version of EVM's) This patch is based on intial version from Charulatha V, reference to original discussion - http://www.mail-archive.com/linux-omap@xxxxxxxxxxxxxxx/msg35784.html Signed-off-by: Vaibhav Hiremath <hvaibhav@xxxxxx> Signed-off-by: Charulatha V <charu@xxxxxx> Tested-by: Kevin Hilman <khilman@xxxxxx> --- Since Kevin reported that this patch doesn't get applied cleanly, so I am reposting it again after making sure that it gets applied cleanly. arch/arm/mach-omap2/board-omap3evm.c | 39 +++++++++++++++++++++++++++++++++- 1 files changed, 38 insertions(+), 1 deletions(-) diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index 323c380..97e0f65 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -58,6 +58,13 @@ #define OMAP3EVM_ETHR_ID_REV 0x50 #define OMAP3EVM_ETHR_GPIO_IRQ 176 #define OMAP3EVM_SMSC911X_CS 5 +/* + * Eth Reset signal + * 64 = Generation 1 (<=RevD) + * 7 = Generation 2 (>=RevE) + */ +#define OMAP3EVM_GEN1_ETHR_GPIO_RST 64 +#define OMAP3EVM_GEN2_ETHR_GPIO_RST 7 static u8 omap3_evm_version; @@ -124,10 +131,15 @@ static struct platform_device omap3evm_smsc911x_device = { static inline void __init omap3evm_init_smsc911x(void) { - int eth_cs; + int eth_cs, eth_rst; struct clk *l3ck; unsigned int rate; + if (get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1) + eth_rst = OMAP3EVM_GEN1_ETHR_GPIO_RST; + else + eth_rst = OMAP3EVM_GEN2_ETHR_GPIO_RST; + eth_cs = OMAP3EVM_SMSC911X_CS; l3ck = clk_get(NULL, "l3_ck"); @@ -136,6 +148,27 @@ static inline void __init omap3evm_init_smsc911x(void) else rate = clk_get_rate(l3ck); + /* Configure ethernet controller reset gpio */ + if (cpu_is_omap3430()) { + if (gpio_request(eth_rst, "SMSC911x gpio") < 0) { + pr_err(KERN_ERR "Failed to request %d for smsc911x\n", + eth_rst); + return; + } + + if (gpio_direction_output(eth_rst, 1) < 0) { + pr_err(KERN_ERR "Failed to set direction of %d for" \ + " smsc911x\n", eth_rst); + return; + } + /* reset pulse to ethernet controller*/ + usleep_range(150, 220); + gpio_set_value(eth_rst, 0); + usleep_range(150, 220); + gpio_set_value(eth_rst, 1); + usleep_range(1, 2); + } + if (gpio_request(OMAP3EVM_ETHR_GPIO_IRQ, "SMSC911x irq") < 0) { printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n", OMAP3EVM_ETHR_GPIO_IRQ); @@ -658,6 +691,10 @@ static struct omap_board_mux board_mux[] __initdata = { OMAP_PIN_OFF_WAKEUPENABLE), OMAP3_MUX(MCSPI1_CS1, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_INPUT_PULLUP | OMAP_PIN_OFF_OUTPUT_LOW), + OMAP3_MUX(SYS_BOOT5, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | + OMAP_PIN_OFF_NONE), + OMAP3_MUX(GPMC_WAIT2, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP | + OMAP_PIN_OFF_NONE), { .reg_offset = OMAP_MUX_TERMINATOR }, }; #endif -- 1.6.2.4 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
