Thara Gopinath had written, on 12/31/2010 02:07 AM, the following:
The smartreflex bit on twl4030 needs to be enabled by default irrespective
of whether smartreflex module is enabled on the OMAP side or not.
This is because without this bit enabled the voltage scaling through
vp forceupdate does not function properly on OMAP3.
s/does not function properly/ does not function ;)
SR I2C is used for forceupdate/vc bypass modes - so neither will
function without switching t2 mode.
T2 voltages could be set in quiet a few methods:
a) Synchronized Scaling Hardware Strategy (ENABLE_VMODE = 1) (for OMAP2
and I had worked on one OMAP3430 product which used this as well) using
VDD1_VFLOOR and VDD1_VROOF
b) Direct Strategy Software Scaling Mode (ENABLE_VMODE = 0) (Smart
reflex disabled) - VDD1_VSEL
c) using smart reflex - as done below - allows OMAP with smart reflex
hardware wired to the twl to use that functionality.
Blindly setting it to smartreflex mode is not correct IMHO. It might
work on SDP and few TI and non-TI platforms, but not all.
Signed-off-by: Thara Gopinath <thara@xxxxxx>
---
This patch is against LO master and has been
tested on OMAP3430 SDP and OMAP2430 SDP.
arch/arm/mach-omap2/omap_twl.c | 16 ++++++++++++++++
1 files changed, 16 insertions(+), 0 deletions(-)
diff --git a/arch/arm/mach-omap2/omap_twl.c b/arch/arm/mach-omap2/omap_twl.c
index 15f8c6c..a59f36b 100644
--- a/arch/arm/mach-omap2/omap_twl.c
+++ b/arch/arm/mach-omap2/omap_twl.c
@@ -58,7 +58,9 @@
static bool is_offset_valid;
static u8 smps_offset;
+#define TWL4030_DCDC_GLOBAL_CFG 0x06
#define REG_SMPS_OFFSET 0xE0
+#define SMARTREFLEX_ENABLE BIT(3)
unsigned long twl4030_vsel_to_uv(const u8 vsel)
{
@@ -256,6 +258,7 @@ int __init omap4_twl_init(void)
int __init omap3_twl_init(void)
{
struct voltagedomain *voltdm;
+ u8 temp;
if (!cpu_is_omap34xx())
return -ENODEV;
@@ -267,6 +270,19 @@ int __init omap3_twl_init(void)
omap3_core_volt_info.vp_vddmax = OMAP3630_VP2_VLIMITTO_VDDMAX;
}
+ /*
+ * The smartreflex bit on twl4030 needs to be enabled by
+ * default irrespective of whether smartreflex module is
+ * enabled on the OMAP side or not. This is because without
+ * this bit enabled the voltage scaling through
+ * vp forceupdate does not function properly on OMAP3.
+ */
+ twl_i2c_read_u8(TWL4030_MODULE_PM_RECEIVER, &temp,
+ TWL4030_DCDC_GLOBAL_CFG);
+ temp |= SMARTREFLEX_ENABLE;
+ twl_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, temp,
+ TWL4030_DCDC_GLOBAL_CFG);
+
voltdm = omap_voltage_domain_lookup("mpu");
omap_voltage_register_pmic(voltdm, &omap3_mpu_volt_info);
--
Regards,
Nishanth Menon
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html