On Thu, Dec 16, 2010 at 11:47 PM, Kevin Hilman <khilman@xxxxxxxxxxxxxxxxxxx> wrote: > Hi Govindraj, > > "Raja, Govindraj" <govindraj.raja@xxxxxx> writes: > >> On Wed, Dec 15, 2010 at 9:42 PM, Kevin Hilman <khilman@xxxxxxxxxxxxxxxxxxx> >> wrote: >> >> "Govindraj.R" <govindraj.raja@xxxxxx> writes: >> >> > Changes invloves: >> > ---------------- >> > 1) Addition of hwmod data for omap2/3/4. >> > 1) McSPI driver hwmod adaptation with cleanup of base address >> > macros and using omap-device API's. >> > 2) Runtime Conversion of McSPI driver >> > >> > Changes from v1: >> > --------------- >> > 1) Fixing patch 5/5 comments for hwmod+runtime >> > Split the patch 5/5 to hwmod adaptation >> > and then runtime conversion >> > http://www.mail-archive.com/linux-omap@xxxxxxxxxxxxxxx/msg33387.html >> > >> > Testing Updates: >> > ---------------- >> > Was tested using data transfer test module available at: >> > http://dev.omapzoom.org/?p=richo/device_driver_test.git;a=blob;f=mcspi/ >> test_code/ >> > utils/mcspi_modules/omap_mcspi_datatest.c; >> > h=e42ec10c5c844abdde6a7175a268b379fbbdb655; >> > hb=5d9a755d50e58de861c5e8991f2f607bc49b5dc3 >> >> Can you summarize what this test does? >> >> On what platforms was this tested? >> >> How was it tested for OMAP1 and OMAP2? >> >> >> >> Using the above mentioned test module we had done some >> data transfer tests. >> Platforms used used where : >> 1) OMAP2430 SDP. >> 2) OMAP3 (ZOOM boards zoom2/3). >> 3) OMAP4430 SDP [ Here even basic Ethernet functionality was checked which is >> over SPI interface] > > Can you describe a little more about the testing please? What exactly > does the data transfer test do? Is it a loopback test? Does it use > on-board SPI peripherals? If so, which ones, etc. > Yes its an loopback test based on SPI interface available from development board expansion connector. MISO <---> MOSI [Loopback test] So basically looking into the Board schematics we decide which SPI interface is available on the board expansion connector and use SPI interface available. On zoom boards SPI3 was available on expansion connector and same was used. On 4430SDP SPI2 interface was used. On 2430SDP SPI2. Also for testing, spi_board_info was populated in board file and spi_register_board_info was done, here bus info was populated based on spi bus available on the board. In spi_board_info structure we initialize spi_bus and name as spitst and speed and chip-select later once test module is loaded word-length, speed etc is modified from proc interface available from the test module and data test is done. -- Thanks, Govindraj.R >> We boot tested on 2420/n800. >> >> Coming to omap1, >> >> This driver[omap2_mcspi.c] is applicable only from omap2_plus >> for omap1 omap_uwire.c is the spi driver file. > > OK, thanks for clarification. > > Kevin > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
