2010/9/24 Tony Lindgren <tony@xxxxxxxxxxx>:
> * MichaÅ MirosÅaw <mirqus@xxxxxxxxx> [100924 09:03]:
>> W dniu 24 wrzeÅnia 2010 17:38 uÅytkownik Cory Maccarrone
>> <darkstar6262@xxxxxxxxx> napisaÅ:
>> > 2010/9/24 MichaÅ MirosÅaw <mirqus@xxxxxxxxx>:
>> >> 2010/8/18 Cory Maccarrone <darkstar6262@xxxxxxxxx>:
>> >>> This change adds in MMC and I2C support to the HTC Herald board, as well
>> >>> as adding the HTCPLD driver for the PLD used on this phone. ÂIt also
>> >>> adds in the gpio-keys entries for the front directional keys and
>> >>> selector and the cursor keys on the slide-out keyboard, and gpio-leds
>> >>> support for the LEDs attached to the htcpld.
>> >>>
>> >>> Additionally, SPI bus support (using the spi100k driver) and
>> >>> touchscreen support (using the ads7846 driver) were added.
>> >>>
>> >>> Signed-off-by: Cory Maccarrone <darkstar6262@xxxxxxxxx>
>> >>> ---
>> >> [...]
>> >>> +/* MMC Card */
>> >>> +#if defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE)
>> >>> +static struct omap_mmc_platform_data htc_mmc1_data = {
>> >>> +    .nr_slots            = 1,
>> >>> +    .switch_slot          Â= NULL,
>> >>> + Â Â Â .slots[0] Â Â Â = {
>> >>> +        .ocr_mask        = MMC_VDD_28_29 | MMC_VDD_30_31 |
>> >>> + Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â MMC_VDD_32_33 | MMC_VDD_33_34,
>> >>> +        .name          = "mmcblk",
>> >>> +        .nomux         Â= 1,
>> >>> +        .wires         Â= 4,
>> >>> +        .switch_pin       = -1,
>> >>> + Â Â Â },
>> >>> +};
>> >> [...]
>> >> What voltages can this MMC controller provide? That's a rather unusual OCR mask.
>> > Not really sure, I wasn't the one who first came up with that mask.
>> > All I know is that it seems to work, and not just for my device, but
>> > lots of other HTC OMAP850 devices we've tried it on too.
>> >
>> > I'm interested though, what in particular makes it unusual?
>>
>> It specifies, that device supports voltage ranges:
>> 2.8V - 2.9V, 3.0V - 3.1V, 3.2V - 3.4V
>> (so: 2.9V - 3.0V and 3.1V - 3.2V are not available).
>> Are there really 2.8V, 3.0V, 3.3V VDDs settable?
>>
>> If the host supports only VDD = 3.3V for example, then correct OCR
>> mask would be: MMC_VDD_32_33 | MMC_VDD_33_34 (or just one flag).
>
> Looks like also board-sx1-mmc.c and board-h[23]-mmc.c have the
> same spotty voltage range.
>
> Cory, care to do a patch that fixes it for all of them?
>
Yeah, I can do that. I'll resubmit this patch too with the fixed up ranges.
- Cory
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
