Thara Gopinath <thara@xxxxxx> writes: > From: thara gopinath <thara@xxxxxx> > > This patch series introduces smartreflex and voltage driver support > for OMAP3430 and OMAP3630. SmartReflex modules do adaptive voltage > control for real-time voltage adjustments. [...] > This patch series is based against origin/pm-core branch off > Kevin's pm tree which in turn is based off lo-master. > This series will apply against lo-master also but will > break compilation due to lack of opp framework support > on lo-master. > > This patch series has been tested on OMAP3430 SDP with the extra five patches > from origin/cpufreq branch off Kevin's pm tree applied. This series > has been tested with with omap3_defconfig with the following > menuconfig options enabled. > System type -> TI OMAP Implementations -> Smartreflex Support > System type -> TI OMAP Implementations -> > Class 3 mode of Smartreflex Implementation Using the same baseline as you mention above (pm-core + pm-opp), I applied this series (and the OMAP4 series) and tested on 34xx/n900 and 36xx/Zoom3 using omap2plus_defconfig and it booted ok. (I also patched the n900 board file to call sr_class3_init(), which you should include as part of the series too.) I then did some experiments, including updating the pm-sr branch to be this latest series and testing with omap3_pm_defconfig. With that, I notcied that within a few seconds of reaching the shell, the system rebooted. I tracked this down to the fact that CONFIG_OMAP_WATCHDOG was not enabled in omap3_pm_defconfig. Enabling the watchdog, and it no longer reboots. /me confused Using just the pm-sr branch by itself and omap2plus_defconfig, even with the watchdog disabled, it doesn't reboot. Do you have any ideas what else might be causing this reboot when using the PM branch + omap3_pm_defconfig? Kevin > Thara Gopinath (11): > OMAP: PM: Export the main pm debugfs directory > OMAP3: PM: Adding voltage driver support for OMAP3 > OMAP3: PM: Adding smartreflex driver support. > OMAP3: PM: Adding smartreflex device file. > OMAP3: PM: Adding smartreflex hwmod data > OMAP3: PM: Adding smartreflex class3 driver > OMAP3: PM: Adding T2 enabling of smartreflex support > OMAP3: PM: Adding debug support to Voltage and Smartreflex drivers > OMAP3: PM: Smartreflex Class3 initialization from board files. > OMAP3: PM: Program correct init voltages for VDD1 and VDD2 > OMAP3: PM: Register TWL4030 pmic info with the voltage driver. > > arch/arm/mach-omap2/Makefile | 5 +- > arch/arm/mach-omap2/board-3430sdp.c | 2 + > arch/arm/mach-omap2/board-zoom-peripherals.c | 2 + > arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 249 +++++ > arch/arm/mach-omap2/pm-debug.c | 18 + > arch/arm/mach-omap2/pm.c | 67 ++- > arch/arm/mach-omap2/pm.h | 1 + > arch/arm/mach-omap2/smartreflex-class3.c | 61 ++ > arch/arm/mach-omap2/smartreflex-class3.h | 23 + > arch/arm/mach-omap2/smartreflex.c | 1039 +++++++++++++++++++ > arch/arm/mach-omap2/sr_device.c | 174 ++++ > arch/arm/mach-omap2/voltage.c | 1319 +++++++++++++++++++++++++ > arch/arm/plat-omap/Kconfig | 41 + > arch/arm/plat-omap/include/plat/control.h | 27 + > arch/arm/plat-omap/include/plat/smartreflex.h | 276 ++++++ > arch/arm/plat-omap/include/plat/voltage.h | 141 +++ > arch/arm/plat-omap/opp_twl_tps.c | 17 + > drivers/mfd/twl-core.c | 7 +- > drivers/mfd/twl4030-power.c | 29 + > include/linux/i2c/twl.h | 1 + > 20 files changed, 3495 insertions(+), 4 deletions(-) > create mode 100644 arch/arm/mach-omap2/smartreflex-class3.c > create mode 100644 arch/arm/mach-omap2/smartreflex-class3.h > create mode 100644 arch/arm/mach-omap2/smartreflex.c > create mode 100644 arch/arm/mach-omap2/sr_device.c > create mode 100644 arch/arm/mach-omap2/voltage.c > create mode 100644 arch/arm/plat-omap/include/plat/smartreflex.h > create mode 100644 arch/arm/plat-omap/include/plat/voltage.h -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
