Hi balbi,
On Wed, Sep 22, 2010 at 2:21 PM, Felipe Balbi <balbi@xxxxxx> wrote:
> Hi,
>
> On Sat, Sep 18, 2010 at 11:33:56AM -0500, kishore kadiyala wrote:
>>
>> @@ -223,6 +224,81 @@ int twl6030_interrupt_mask(u8 bit_mask, u8 offset)
>> }
>> EXPORT_SYMBOL(twl6030_interrupt_mask);
>>
>> +int twl6030_mmc_card_detect_config(void)
>> +{
>> + int ret;
>> + u8 reg_val = 0;
>> +
>> + /* Unmasking the Card detect Interrupt line for MMC1 from Phoenix
>> */
>> + if (twl_class_is_6030()) {
>
> which other class can this be ?
It can only be a 6030 class.
as twl6030_mmc_card_detect_config is called only in board file I can
remove the check.
>
>> + /*
>> + * Intially Configuring MMC_CTRL for receving interrupts &
>> + * Card status on TWL6030 for MMC1
>> + */
>> + ret = twl_i2c_read_u8(TWL6030_MODULE_ID0, ®_val,
>> TWL6030_MMCCTRL);
>> + if (ret < 0) {
>> + pr_err("twl6030: Failed to read MMCCTRL, error %d\n",
>> ret);
>> + return ret;
>> + }
>> + reg_val &= ~VMMC_AUTO_OFF;
>> + reg_val |= SW_FC;
>> + ret = twl_i2c_write_u8(TWL6030_MODULE_ID0, reg_val,
>> TWL6030_MMCCTRL);
>> + if (ret < 0) {
>> + pr_err("twl6030: Failed to write MMCCTRL, error %d\n",
>> ret);
>> + return ret;
>> + }
>> +
>> + /* Configuring PullUp-PullDown register */
>> + ret = twl_i2c_read_u8(TWL6030_MODULE_ID0, ®_val,
>> + TWL6030_CFG_INPUT_PUPD3);
>
> is this a gpio ? Could gpiolib take care of this ?
This is not a gpio but an interrupt line from twl6030 to MMC controller
>
>> + if (ret < 0) {
>> + pr_err("twl6030: Failed to read CFG_INPUT_PUPD3, error
>> %d\n",
>> +
>> ret);
>> + return ret;
>> + }
>> + reg_val &= ~(MMC_PU | MMC_PD);
>> + ret = twl_i2c_write_u8(TWL6030_MODULE_ID0, reg_val,
>> + TWL6030_CFG_INPUT_PUPD3);
>
> ditto.
This is not a gpio
>
>> +int twl6030_mmc_card_detect(struct device *dev, int slot)
>> +{
>> + int ret = -EIO;
>> + u8 read_reg = 0;
>> + struct platform_device *pdev = container_of(dev,
>> + struct platform_device, dev);
>
> how about:
>
> struct platform_device *pdev = to_platform_device(dev);
ok will use this .
>
>> diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
>> index 562dbbb..a51894d 100644
>> --- a/drivers/mmc/host/omap_hsmmc.c
>> +++ b/drivers/mmc/host/omap_hsmmc.c
>> @@ -466,8 +466,6 @@ static int omap_hsmmc_gpio_init(struct
>> omap_mmc_platform_data *pdata)
>> int ret;
>>
>> if (gpio_is_valid(pdata->slots[0].switch_pin)) {
>> - pdata->suspend = omap_hsmmc_suspend_cdirq;
>> - pdata->resume = omap_hsmmc_resume_cdirq;
>> if (pdata->slots[0].cover)
>> pdata->slots[0].get_cover_state =
>> omap_hsmmc_get_cover_state;
>> @@ -2211,6 +2209,8 @@ static int __init omap_hsmmc_probe(struct
>> platform_device *pdev)
>> "Unable to grab MMC CD IRQ\n");
>> goto err_irq_cd;
>> }
>> + pdata->suspend = omap_hsmmc_suspend_cdirq;
>> + pdata->resume = omap_hsmmc_resume_cdirq;
>
> this doesn't look to be part of $SUBJECT, care to explain ?
I've just moved the initialization of suspend & resume which was
previously done in omap_hsmmc_gpio_init.
Ok will update in the log
>
>> @@ -173,6 +183,27 @@ int twl_i2c_read(u8 mod_no, u8 *value, u8 reg,
>> unsigned num_bytes);
>> int twl6030_interrupt_unmask(u8 bit_mask, u8 offset);
>> int twl6030_interrupt_mask(u8 bit_mask, u8 offset);
>>
>> +/* Card detect Configuration for MMC1 Controller on OMAP4 */
>> +#ifdef CONFIG_TWL4030_CORE
>> +int twl6030_mmc_card_detect_config(void);
>> +#else
>> +static inline int twl6030_mmc_card_detect_config(void)
>> +{
>> + pr_err("twl6030_mmc_card_detect_config not supported\n");
>
> pr_debug() would be better ??
ok will update with pr_debug
>
>> +/* MMC1 Controller on OMAP4 uses Phoenix irq for Card detect */
>> +#ifdef CONFIG_TWL4030_CORE
>> +int twl6030_mmc_card_detect(struct device *dev, int slot);
>> +#else
>> +static inline int twl6030_mmc_card_detect(struct device *dev, int slot)
>> +{
>> + pr_err("Call back twl6030_mmc_card_detect not supported\n");
>
> ditto.
ok will update with pr_debug
>
> --
> balbi
Regards,
Kishore
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
