On Wed, Jun 23, 2010 at 07:18:00AM +0200, ext Nagarajan, Rajkumar wrote: > > DISPC DMA optimization has been enabled and vrfb calls changed as required. > Optimization reduces the memory traffic (DDR memory) when rotation is set > to 90- and 270- degree and SMS-VRFB rotation engine is used. > > With this change, > L3 interconnect traffic is reduced by a factor 2x for YUV422 & UYVY > DDR memory traffic is reduced by a factor 2x for YUV422 & UYVY. > > Signed-off-by: Mukund Mittal <mmittal@xxxxxx> > Signed-off-by: Kishore Y <kishore.y@xxxxxx> > Signed-off-by: Rajkumar N <rajkumar.nagarajan@xxxxxx> > --- > arch/arm/plat-omap/include/plat/vrfb.h | 6 +++- > drivers/media/video/omap/omap_vout.c | 2 +- > drivers/video/omap2/dss/dispc.c | 39 +++++++++++++++++++++++------- > drivers/video/omap2/omapfb/omapfb-main.c | 2 +- > drivers/video/omap2/vrfb.c | 18 ++++++++++--- > 5 files changed, 50 insertions(+), 17 deletions(-) > > diff --git a/arch/arm/plat-omap/include/plat/vrfb.h b/arch/arm/plat-omap/include/plat/vrfb.h > index d8a03ce..fba9ecd 100644 > --- a/arch/arm/plat-omap/include/plat/vrfb.h > +++ b/arch/arm/plat-omap/include/plat/vrfb.h > @@ -23,6 +23,8 @@ > > #define OMAP_VRFB_LINE_LEN 2048 > > +#include <plat/display.h> > + > struct vrfb { > u8 context; > void __iomem *vaddr[4]; > @@ -42,8 +44,8 @@ extern void omap_vrfb_adjust_size(u16 *width, u16 *height, > extern u32 omap_vrfb_min_phys_size(u16 width, u16 height, u8 bytespp); > extern u16 omap_vrfb_max_height(u32 phys_size, u16 width, u8 bytespp); > extern void omap_vrfb_setup(struct vrfb *vrfb, unsigned long paddr, > - u16 width, u16 height, > - unsigned bytespp, bool yuv_mode); > + u16 width, u16 height, unsigned bytespp, > + enum omap_color_mode color_mode, int rotation); > extern int omap_vrfb_map_angle(struct vrfb *vrfb, u16 height, u8 rot); > extern void omap_vrfb_restore_context(void); > > diff --git a/drivers/media/video/omap/omap_vout.c b/drivers/media/video/omap/omap_vout.c > index b74884b..b3f94ca 100644 > --- a/drivers/media/video/omap/omap_vout.c > +++ b/drivers/media/video/omap/omap_vout.c > @@ -465,7 +465,7 @@ static int omap_vout_vrfb_buffer_setup(struct omap_vout_device *vout, > for (i = 0; i < *count; i++) > omap_vrfb_setup(&vout->vrfb_context[i], > vout->smsshado_phy_addr[i], vout->pix.width, > - vout->pix.height, vout->bpp, yuv_mode); > + vout->pix.height, vout->bpp, vout->dss_mode, vout->rotation); > > return 0; > } > diff --git a/drivers/video/omap2/dss/dispc.c b/drivers/video/omap2/dss/dispc.c > index e777e35..cb8eba4 100644 > --- a/drivers/video/omap2/dss/dispc.c > +++ b/drivers/video/omap2/dss/dispc.c > @@ -1059,12 +1059,16 @@ static void _dispc_set_vid_accu1(enum omap_plane plane, int haccu, int vaccu) > dispc_write_reg(ac1_reg[plane-1], val); > } > > +static void _dispc_set_vdma_attrs(enum omap_plane plane, bool enable) > +{ > + REG_FLD_MOD(dispc_reg_att[plane], enable ? 1 : 0, 20, 20); > +} > > static void _dispc_set_scaling(enum omap_plane plane, > u16 orig_width, u16 orig_height, > u16 out_width, u16 out_height, > bool ilace, bool five_taps, > - bool fieldmode) > + bool fieldmode, bool vdma) > { > int fir_hinc; > int fir_vinc; > @@ -1080,12 +1084,12 @@ static void _dispc_set_scaling(enum omap_plane plane, > > _dispc_set_scale_coef(plane, hscaleup, vscaleup, five_taps); > > - if (!orig_width || orig_width == out_width) > + if (!orig_width || (!vdma && (orig_width == out_width))) > fir_hinc = 0; > else > fir_hinc = 1024 * orig_width / out_width; > > - if (!orig_height || orig_height == out_height) > + if (!orig_height || (!vdma && (orig_height == out_height))) > fir_vinc = 0; > else > fir_vinc = 1024 * orig_height / out_height; > @@ -1164,10 +1168,6 @@ static void _dispc_set_rotation_attrs(enum omap_plane plane, u8 rotation, > > REG_FLD_MOD(dispc_reg_att[plane], vidrot, 13, 12); > > - if (rotation == OMAP_DSS_ROT_90 || rotation == OMAP_DSS_ROT_270) > - REG_FLD_MOD(dispc_reg_att[plane], 0x1, 18, 18); > - else > - REG_FLD_MOD(dispc_reg_att[plane], 0x0, 18, 18); So VIDROWREPEAT is supposed to be off when vid DMA optimization is on? There's no mention of that in the TRM. > } else { > REG_FLD_MOD(dispc_reg_att[plane], 0, 13, 12); > REG_FLD_MOD(dispc_reg_att[plane], 0, 18, 18); > @@ -1504,6 +1504,17 @@ static unsigned long calc_fclk(u16 width, u16 height, > return dispc_pclk_rate() * vf * hf; > } > > +static int dispc_is_vdma_req(u8 rotation, enum omap_color_mode color_mode) > +{ > +/* TODO: VDMA support for RGB16 mode */ > + if (cpu_is_omap3630()) Is video DMA optimization broken on 34xx? I tried to enable it on a 3430 at some point but didn't see any obvious improvement. However the 34xx TRM didn't say anything about 5-tap so perhaps it just didn't actually do anything. > + if ((color_mode == OMAP_DSS_COLOR_YUV2) || > + (color_mode == OMAP_DSS_COLOR_UYVY)) > + if ((rotation == 1) || (rotation == 3)) > + return true; > + return false; > +} > + > void dispc_set_channel_out(enum omap_plane plane, enum omap_channel channel_out) > { > enable_clocks(1); > @@ -1623,6 +1634,8 @@ static int _dispc_setup_plane(enum omap_plane plane, > if (cpu_is_omap34xx() && height > out_height && > fclk > dispc_fclk_rate()) > five_taps = true; > + if (dispc_is_vdma_req(rotation, color_mode)) > + five_taps = true; Maybe it would make sense to change the code back to trying 5-tap first and fall back to 3-tap if the required clock is too high? > } > > if (width > (2048 >> five_taps)) { > @@ -1694,9 +1707,17 @@ static int _dispc_setup_plane(enum omap_plane plane, > _dispc_set_pic_size(plane, width, height); > > if (plane != OMAP_DSS_GFX) { > - _dispc_set_scaling(plane, width, height, > + if (dispc_is_vdma_req(rotation, color_mode)) { > + _dispc_set_scaling(plane, width, height, > out_width, out_height, > - ilace, five_taps, fieldmode); > + ilace, five_taps, fieldmode, 1); > + _dispc_set_vdma_attrs(plane, 1); > + } else { > + _dispc_set_scaling(plane, width, height, > + out_width, out_height, > + ilace, five_taps, fieldmode, 0); > + _dispc_set_vdma_attrs(plane, 0); > + } Less copy-pasting: bool vdma = dispc_is_vdma_req(); _dispc_set_scaling(..., vdma); _dispc_set_vdma_attrs(..., vdma); > _dispc_set_vid_size(plane, out_width, out_height); > _dispc_set_vid_color_conv(plane, cconv); > } > diff --git a/drivers/video/omap2/omapfb/omapfb-main.c b/drivers/video/omap2/omapfb/omapfb-main.c > index 73ecc9f..33fd427 100644 > --- a/drivers/video/omap2/omapfb/omapfb-main.c > +++ b/drivers/video/omap2/omapfb/omapfb-main.c > @@ -552,7 +552,7 @@ static int setup_vrfb_rotation(struct fb_info *fbi) > omap_vrfb_setup(&rg->vrfb, rg->paddr, > var->xres_virtual, > var->yres_virtual, > - bytespp, yuv_mode); > + bytespp, mode, 0); > > /* Now one can ioremap the 0 angle view */ > r = omap_vrfb_map_angle(vrfb, var->yres_virtual, 0); > diff --git a/drivers/video/omap2/vrfb.c b/drivers/video/omap2/vrfb.c > index fd22716..38d03d1 100644 > --- a/drivers/video/omap2/vrfb.c > +++ b/drivers/video/omap2/vrfb.c > @@ -157,7 +157,7 @@ EXPORT_SYMBOL(omap_vrfb_max_height); > > void omap_vrfb_setup(struct vrfb *vrfb, unsigned long paddr, > u16 width, u16 height, > - unsigned bytespp, bool yuv_mode) > + unsigned bytespp, enum omap_color_mode color_mode, int rotation) > { > unsigned pixel_size_exp; > u16 vrfb_width; > @@ -167,11 +167,12 @@ void omap_vrfb_setup(struct vrfb *vrfb, unsigned long paddr, > u32 control; > > DBG("omapfb_set_vrfb(%d, %lx, %dx%d, %d, %d)\n", ctx, paddr, > - width, height, bytespp, yuv_mode); > + width, height, bytespp, color_mode); > > /* For YUV2 and UYVY modes VRFB needs to handle pixels a bit > * differently. See TRM. */ > - if (yuv_mode) { > + if (color_mode == OMAP_DSS_COLOR_YUV2 || > + color_mode == OMAP_DSS_COLOR_UYVY) { > bytespp *= 2; > width /= 2; > } > @@ -183,6 +184,13 @@ void omap_vrfb_setup(struct vrfb *vrfb, unsigned long paddr, > else > BUG(); > > + /* for vdma */ > + /* TODO: VDMA support for RGB16 mode */ > + if (cpu_is_omap3630()) > + if (color_mode == OMAP_DSS_COLOR_YUV2) > + if ((rotation == 1) || (rotation == 3)) > + pixel_size_exp = 2; > + where did UYVY go? Also what's this supposed to do? pixel_size_exp will be to 2 for YUV anyway. > vrfb_width = ALIGN(width * bytespp, VRFB_PAGE_WIDTH) / bytespp; > vrfb_height = ALIGN(height, VRFB_PAGE_HEIGHT); > > @@ -211,7 +219,9 @@ void omap_vrfb_setup(struct vrfb *vrfb, unsigned long paddr, > vrfb->xoffset = vrfb_width - width; > vrfb->yoffset = vrfb_height - height; > vrfb->bytespp = bytespp; > - vrfb->yuv_mode = yuv_mode; > + if (color_mode == OMAP_DSS_COLOR_YUV2 || > + color_mode == OMAP_DSS_COLOR_UYVY) > + vrfb->yuv_mode = true; > } > EXPORT_SYMBOL(omap_vrfb_setup); > > -- > 1.5.4.3 > -- > To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html -- Ville Syrjälä -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html