Nishanth Menon <nm@xxxxxx> writes: > From: Deepak K <deepak.k@xxxxxx> > > Original patch: > http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=42d4a342c009bd9727c100abc8a4bc3063c22f0c > > Errata i202 (OMAP3430 - 1.12, OMAP3630 - 1.6): This workaround is currently done for all OMAPs. Presumably, this errata will eventually be fixed. So, as with other errata fixes, we need some sort of SoC-rev based flag and the errata workaround done based on that flag. Also, shouldn't there be a fix for this in the 8250 and omap-serial drivers too? Kevin > UART module MDR1 register access can cause a dummy underrun > condition which could result in a freeze in the case of IrDA > communication or if used as UART, corrupted data. > > Workaround is as follows for everytime MDR1 register is changed: > * setup all required UART registers > * setup MDR1.MODE_SELECT bit field > * Wait 5 L4 clk cycles + 5 UART functional clock cycles > * Clear the Tx and RX fifo using FCR register > > Note: The following step is not done as I am assuming it is not > needed due to reconfiguration being done and there is no halted > operation perse. > * Read if required, the RESUME register to resume halted operation > > Cc: Govindraj R <govindraj.raja@xxxxxx> > Cc: Kevin Hilman <khilman@xxxxxxxxxxxxxxxxxxx> > Cc: Tero Kristo <tero.kristo@xxxxxxxxx> > > Signed-off-by: Deepak K <deepak.k@xxxxxx> > Signed-off-by: Nishanth Menon <nm@xxxxxx> > --- > Changes from V2: > * Use macros instead of hardcoded values > > Ref: > V2: http://marc.info/?t=127084514600010&r=1&w=2&n=2 > v1: http://marc.info/?t=127074933100005&r=1&w=2 > > arch/arm/mach-omap2/serial.c | 41 ++++++++++++++++++++++++++++++++++++++--- > 1 files changed, 38 insertions(+), 3 deletions(-) > > diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c > index a7c45b5..6d13183 100644 > --- a/arch/arm/mach-omap2/serial.c > +++ b/arch/arm/mach-omap2/serial.c > @@ -185,6 +185,42 @@ static inline void __init omap_uart_reset(struct omap_uart_state *uart) > > #if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP3) > > +/* > + * Work Around for Errata i202 (3430 - 1.12, 3630 - 1.6) > + * The access to uart register after MDR1 Access > + * causes UART to corrupt data. > + * > + * Need a delay = > + * 5 L4 clock cycles + 5 UART functional clock cycle (@48MHz = ~0.2uS) > + * give 10 times as much > + */ > +static void omap_uart_mdr1_errataset(struct omap_uart_state *uart, u8 mdr1_val, > + u8 fcr_val) > +{ > + struct plat_serial8250_port *p = uart->p; > + u8 timeout = 255; > + > + serial_write_reg(p, UART_OMAP_MDR1, mdr1_val); > + udelay(2); > + serial_write_reg(p, UART_FCR, fcr_val | UART_FCR_CLEAR_XMIT | > + UART_FCR_CLEAR_RCVR); > + /* > + * Wait for FIFO to empty: when empty, RX_FIFO_E bit is 0 and > + * TX_FIFO_E bit is 1. > + */ > + while (UART_LSR_THRE != (serial_read_reg(p, UART_LSR) & > + (UART_LSR_THRE | UART_LSR_DR))) { > + timeout--; > + if (!timeout) { > + /* Should *never* happen. we warn and carry on */ > + dev_crit(&uart->pdev.dev, "Errata i202: timedout %x\n", > + serial_read_reg(p, UART_LSR)); > + break; > + } > + udelay(1); > + } > +} > + > static void omap_uart_save_context(struct omap_uart_state *uart) > { > u16 lcr = 0; > @@ -222,7 +258,7 @@ static void omap_uart_restore_context(struct omap_uart_state *uart) > > uart->context_valid = 0; > > - serial_write_reg(p, UART_OMAP_MDR1, 0x7); > + omap_uart_mdr1_errataset(uart, 0x07, 0xA0); > serial_write_reg(p, UART_LCR, 0xBF); /* Config B mode */ > efr = serial_read_reg(p, UART_EFR); > serial_write_reg(p, UART_EFR, UART_EFR_ECB); > @@ -235,14 +271,13 @@ static void omap_uart_restore_context(struct omap_uart_state *uart) > serial_write_reg(p, UART_IER, uart->ier); > serial_write_reg(p, UART_LCR, 0x80); > serial_write_reg(p, UART_MCR, uart->mcr); > - serial_write_reg(p, UART_FCR, 0xA1); > serial_write_reg(p, UART_LCR, 0xBF); /* Config B mode */ > serial_write_reg(p, UART_EFR, efr); > serial_write_reg(p, UART_LCR, UART_LCR_WLEN8); > serial_write_reg(p, UART_OMAP_SCR, uart->scr); > serial_write_reg(p, UART_OMAP_WER, uart->wer); > serial_write_reg(p, UART_OMAP_SYSC, uart->sysc); > - serial_write_reg(p, UART_OMAP_MDR1, 0x00); /* UART 16x mode */ > + omap_uart_mdr1_errataset(uart, 0x00, 0xA1); > } > #else > static inline void omap_uart_save_context(struct omap_uart_state *uart) {} > -- > 1.6.3.3 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
