Kevin Hilman wrote:
While handling PRCM IRQs, mask out interrupts that are not enabled in
PRM_IRQENABLE_MPU. If these are not masked out, non-enabled
interrupts are caught and a WARN() is dumped.
This was noticed using SmartReflex transitions which cause the VPx_*
interrupts to be handled since they are set in PRM_IRQSTATUS_MPU even
but not enabled in PRM_IRQENABLE_MPU.
Signed-off-by: Kevin Hilman <khilman@xxxxxxxxxxxxxxxxxxx>
---
For review here, will be queued with other PM updates for 2.6.35.
arch/arm/mach-omap2/pm34xx.c | 15 ++++++++++-----
1 files changed, 10 insertions(+), 5 deletions(-)
diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c
index fee2efb..63d1843 100644
--- a/arch/arm/mach-omap2/pm34xx.c
+++ b/arch/arm/mach-omap2/pm34xx.c
@@ -266,13 +266,15 @@ static int _prcm_int_handle_wakeup(void)
*/
static irqreturn_t prcm_interrupt_handler (int irq, void *dev_id)
{
- u32 irqstatus_mpu;
+ u32 irqenable_mpu, irqstatus_mpu;
int c = 0;
- do {
- irqstatus_mpu = prm_read_mod_reg(OCP_MOD,
- OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+ irqenable_mpu = prm_read_mod_reg(OCP_MOD,
+ OMAP3_PRM_IRQENABLE_MPU_OFFSET);
+ irqstatus_mpu = prm_read_mod_reg(OCP_MOD,
+ OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+ do {
if (irqstatus_mpu & (OMAP3430_WKUP_ST | OMAP3430_IO_ST)) {
c = _prcm_int_handle_wakeup();
@@ -291,7 +293,10 @@ static irqreturn_t prcm_interrupt_handler (int irq, void *dev_id)
prm_write_mod_reg(irqstatus_mpu, OCP_MOD,
OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
I think that this is partially correct. Only iterating for status bits
that correspond to enabled interrupts is correct. However I think
clearing all of the status bits indiscriminately is bad.
The root of the problem is that status bits get set regardless of
whether the IRQ is enabled (which defies common assumptions). I have
seen the exact same issue on Android after introducing ABB and I just
stopped clearing the register altogether:
http://review.omapzoom.org/#patch,sidebyside,2675,2,arch/arm/mach-omap2/pm34xx.c
This turned about to be a bad idea; for instance VP1_TRANXDONE_ST and
ABB_TRANXDONE_ST are currently polled (no interrupt is enabled). With
the above code it is possible to have a vpforceupdate voltage change or
an ABB OPP change, then get interrupted, and then have the timeouts for
the polled code fail after the interrupt is served since those status
bits got cleared resulting in wasted poll loops and false-positive
WARNs. This has been observed.
I think a better solution for both code bases might be,
prm_write_mod_reg((irqstatus_mpu | irqenable_mpu), OCP_MOD,
OMAP3_PRM_MPU_OFFSET);
Regards,
Mike
- } while (prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET));
+ irqstatus_mpu = prm_read_mod_reg(OCP_MOD,
+ OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+
+ } while (irqstatus_mpu & irqenable_mpu);
return IRQ_HANDLED;
}
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html