On Wed, Mar 31, 2010 at 02:23:53PM +0200, ext Charulatha V wrote:
This patch adds support for implementing OMAP3 GPIO as an
early platform device and adds gpio_init specific to OMAP3
This patch adds device structures for each GPIO device in
OMAP3 architecture. These strutures are not created in a
separate *_data.c file because these structures would be
removed once the driver gets adapted to HWMOD way.
Signed-off-by: Charulatha V <charu@xxxxxx>
---
arch/arm/mach-omap2/gpio3xxx.c | 351 +++++++++++++++++++++++++++++++
arch/arm/mach-omap2/include/mach/gpio.h | 13 +-
2 files changed, 363 insertions(+), 1 deletions(-)
create mode 100644 arch/arm/mach-omap2/gpio3xxx.c
diff --git a/arch/arm/mach-omap2/gpio3xxx.c b/arch/arm/mach-omap2/gpio3xxx.c
new file mode 100644
index 0000000..8f404e7
--- /dev/null
+++ b/arch/arm/mach-omap2/gpio3xxx.c
@@ -0,0 +1,351 @@
+/*
+ * gpio3xxx.c - OMAP3-specific gpio code
+ *
+ * Copyright (C) 2010 Texas Instruments, Inc.
+ *
+ * Author:
+ * Charulatha V <charu@xxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <plat/gpio.h>
+
+/*
+ * OMAP3 GPIO reg offsets
+ */
+static struct gpio_reg_offset omap3_gpio_reg = {
+ .data_in = OMAP24XX_GPIO_DATAIN,
+ .data_out = OMAP24XX_GPIO_DATAOUT,
+ .data_out_set = OMAP24XX_GPIO_SETDATAOUT,
+ .data_out_clear = OMAP24XX_GPIO_CLEARDATAOUT,
+ .dir_ctrl = OMAP24XX_GPIO_OE,
+ .irq_status0 = OMAP24XX_GPIO_IRQSTATUS1,
+ .irq_status1 = OMAP24XX_GPIO_IRQSTATUS2,
+ .irq_mask = OMAP24XX_GPIO_IRQENABLE1,
+ .irq_set = OMAP24XX_GPIO_SETIRQENABLE1,
+ .irq_clear = OMAP24XX_GPIO_CLEARIRQENABLE1,
+ .irq_mask_bits = 0xffffffff,
+ .irq_inv = 0,
+ .wkup_enable = OMAP24XX_GPIO_WAKE_EN,
+ .wkup_clear = OMAP24XX_GPIO_CLEARWKUENA,
+ .wkup_set = OMAP24XX_GPIO_SETWKUENA,
+ .debounce_ena = OMAP24XX_GPIO_DEBOUNCE_EN,
+ .debounce_val = OMAP24XX_GPIO_DEBOUNCE_VAL,
+ .ctrl = OMAP24XX_GPIO_CTRL,
+ .syscfg = OMAP24XX_GPIO_SYSCONFIG,
+ .leveldetect0 = OMAP24XX_GPIO_LEVELDETECT0,
+ .leveldetect1 = OMAP24XX_GPIO_LEVELDETECT1,
+ .rise_detect = OMAP24XX_GPIO_RISINGDETECT,
+ .fall_detect = OMAP24XX_GPIO_FALLINGDETECT,
+ .rev_reg = OMAP24XX_GPIO_REVISION,
+};
+
+/*
+ * OMAP3 GPIO1 interface data
+ */
+static struct __initdata resource omap3_gpio1_resources[] = {
+ {
+ .start = OMAP34XX_GPIO1_BASE,
+ .end = OMAP34XX_GPIO1_BASE + OMAP3_GPIO_AS_LEN - 1,
OMAP34XX_GPIO1_BASE + SZ_4K - 1
+ .flags = IORESOURCE_MEM,
+ },
+ {
+ .start = INT_34XX_GPIO_BANK1,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct __initdata omap_gpio_platform_data omap3_gpio1_config = {
+ .ick_name = "gpio1_ick",
+ .dbck_name = "gpio1_dbck",
do not pass clock names. Update the clkdev entries clk*_data.c
+int __init omap3_early_init_gpio(struct platform_device ***pdev)
I don't see the point in passing ***pdev.
+int __init omap3_gpio_dev_reg(void)
+{
+ if (cpu_is_omap34xx()) {
+ platform_device_register(&omap3_gpio1);
+ platform_device_register(&omap3_gpio2);
+ platform_device_register(&omap3_gpio3);
+ platform_device_register(&omap3_gpio4);
+ platform_device_register(&omap3_gpio5);
+ platform_device_register(&omap3_gpio6);
+ }
platform_add_devices(omap3_gpio_early_dev,
ARRAY_SIZE(omap3_gpio_early_dev);
--
balbi
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
