On 06/11/09 13:32, Sid Boyce wrote: > I have been trying the linux-2.6.32-rc5-omap-dss2 kernel and it halts > with a USB error, DEBUG_LL configured. > Reading boot sector > Loading u-boot.bin from mmc > > > U-Boot 2009.01-dirty (Feb 19 2009 - 12:23:21) > > I2C: ready > OMAP3530-GP rev 2, CPU-OPP2 L3-165MHz > OMAP3 Beagle board + LPDDR/NAND > DRAM: 256 MB > NAND: 256 MiB > Using default environment > > MUSB: using high speed > In: serial usbtty > Out: serial usbtty > Err: serial usbtty > Board revision C > Serial #6b22000300000000040323090d00a00a > Hit any key to stop autoboot: 0 > reading boot.scr > > 679 bytes read > Running bootscript from mmc ... > ## Executing script at 80200000 > reading x-load.bin.ift > > 19840 bytes read > ***** Replacing x-load ***** > Usage: > nand - NAND sub-system > > HW ECC selected > > NAND erase: device 0 offset 0x0, size 0x80000 > ^MErasing at 0x0 -- 25% complete.^MErasing at 0x20000 -- 50% > complete.^MErasing at 0x40000 -- 75% complete.^MErasing at 0x60000 -- > 100% complete. > OK > > NAND write: device 0 offset 0x0, size 0x20000 > 131072 bytes written: OK > > NAND write: device 0 offset 0x20000, size 0x20000 > 131072 bytes written: OK > > NAND write: device 0 offset 0x40000, size 0x20000 > 131072 bytes written: OK > > NAND write: device 0 offset 0x60000, size 0x20000 > 131072 bytes written: OK > reading u-boot-f.bin > > ** Unable to read "u-boot-f.bin" from mmc 0:1 ** > ***** Erasing environment settings ***** > Usage: > nand - NAND sub-system > > > NAND erase: device 0 offset 0x160000, size 0x20000 > ^MErasing at 0x160000 -- 100% complete. > OK > reading normal.scr > > 603 bytes read > ***** Executing normal.scr ***** > ## Executing script at 80200000 > reading uImage.bin > > 3160016 bytes read > ***** Kernel: /dev/mmcblk0p1/uImage.bin ***** > reading ramdisk.gz > > ** Unable to read "ramdisk.gz" from mmc 0:1 ** > ***** RootFS: /dev/mmcblk0p2 ***** > ## Booting kernel from Legacy Image at 80200000 ... > Image Name: Linux-2.6.32-rc5-omap-dss2 > Image Type: ARM Linux Kernel Image (uncompressed) > Data Size: 3159952 Bytes = 3 MB > Load Address: 80008000 > Entry Point: 80008000 > Verifying Checksum ... OK > Loading Kernel Image ... OK > OK > > Starting kernel ... > > Error, the USB hardware is not on B mode > > .config with hashes removed attached. > Same result with other versions of MLO and u-boot.bin. > Regards > Sid. > Sorry attached the wrong file. Regards Sid. -- Sid Boyce ... Hamradio License G3VBV, Licensed Private Pilot Emeritus IBM/Amdahl Mainframes and Sun/Fujitsu Servers Tech Support Specialist, Cricket Coach Microsoft Windows Free Zone - Linux used for all Computing Tasks
Attachment:
o-dss2
Description: Binary data
