**-- SNIP ME
V3 - Bunch of changes:
* Introduce debugfs entries for SR - since these
are variable updates, you can essentially do what we do
with test values, change things but without a rebuild!
* Removed the test values altogether
* srid is standardised to u8 and it is not a bit field
* Guilhem's changes for non-twl5030 PMIC incorporated
* uses ioremap
V2 - made possible to work with non twl5030 PMICs
V1 - original rewrite
**-- END OF SNIP ME
Refactor the smart reflex implementation.
Original implementation summary:
Eduardo Valentin (1):
OMAP3: PM: SmartReflex: Fix scheduled while atomic problem
Kalle Jokiniemi (1):
OMAP3: PM: SmartReflex driver integration
Kevin Hilman (1):
temp: SR: IO_ADDRESS conversion
Phil Carmody (2):
OMAP3: PM: Don't do unnecessary searches in omap_sr_vdd*_autocomp_store
OMAP3: PM: Early exit on invalid parameters
Rajendra Nayak (10):
OMAP3: SR: Fix init voltage on OPP change
OMAP3: SR: Update VDD1/2 voltages at boot
OMAP3: SR: Use sysclk for SR CLKLENGTH calc
OMAP3: SR: Reset voltage level on SR disable
OMAP3: SR: Replace printk's with pr_* calls
OMAP3: SR: Remove redundant defines
OMAP3: SR: Replace (0x1 << n) with BIT(n)
OMAP3: SR: Fix SR driver to check for omap-pm return values
OMAP3: PM: Put optimal SMPS stabilization delay
OMAP3: SR: Wait for VP idle before a VP disable
Roger Quadros (4):
OMAP3: PM: Fix Smartreflex when used with PM_NOOP layer
OMAP3: PM: Make Smartreflex driver independent of SRF
OMAP3: PM: Do not Enable SmartReflex if OPP tables not defined
OMAP3: PM: Smartreflex: Fix VDD2 OPP determining logic
Teerth Reddy (1):
OMAP3: SR: Replace SR_PASS/FAIL,SR_TRUE/FALSE
This patch introduces the following changes in addition to refactoring
the implementation:
a) changes the DVFS transition sequences from:
freq, voltage(SR+vp) and viceversa
TO:
disable_vp,SR; freq, voltage(SR+vp) and viceversa; enable_vp,SR
[NOTE: sequence change for disable path - was sr_dis,vp_dis]
This change prevents spikes and unexpected voltage changes
as a result of SR being left enabled at wrong times
b) Major rewrite of smartreflex.c to do the following:
1) Support VCbypass style of voltage configuration as optional
introduce and support forceupdate default as recommended by
OMAP3430 TRM.
2) Centralize operations to allow for simpler and predictable code
flows
3) Modification to SR configured values to be inline with
silicon characterization results
4) cleanup of header
5) Introduce a few omap_pmic weak functions which can be overridden
by platforms implementing PMICs which are different from TWL4030
derivatives
6) srid is standardised to u8 and it is not a bit field
c) Fix ERRCONFIG access to prevent unplanned cleanup of interrupt
status registers - this is done using a interrupt status mask
d) Test nvalues removed instead use debugfs entries to set any values
you like - no more Kconfig option either..
e) Setup h/w timeout based on cpu sysclk and not hardcoded values
g) finegrained with raw register values available over
debugfs in <debugfs mount point>/<pm_debug mount point>/
smartreflex/{srid}/
nvalue_opp[1-5] - nvalues for all 5 opps
following register tweakability:
VP register values:
vplimito_value
vpstepmax_value
vpstepmin_value
vpconfig_value
SR Register values:
sr_errconfig_value
sr_config_value
Advice: disable SR before hitting them, no checks at this point.
test value equivalent userspace bash script would be:
mount -t debugfs none /dbg
mount -t sysfs none /sys
#vdd1:
#0x00AAB48A - OPP3
echo -n "11187338" >/dbg/pm_debug/smartreflex/1/nvalue_opp3
#0x00ABA2E6 - OPP4
echo -n "11248358" >/dbg/pm_debug/smartreflex/1/nvalue_opp4
# 0x00AB90D3 - OPP5
echo -n "11243731" >/dbg/pm_debug/smartreflex/1/nvalue_opp5
#setup senn and senp value (essentially +120)
x=`cat /dbg/pm_debug/smartreflex/1/sr_config_value`
y=$((x + 120))
echo -n $y>/dbg/pm_debug/smartreflex/1/sr_config_value
#and enable it..
echo -n "1" >/sys/power/sr_vdd1_autocomp
#vdd2
#0x00AAC695 -OPP3
echo -n "11191957" > /dbg/pm_debug/smartreflex/2/nvalue_opp3
#setup senn and senp value (essentially +120)
x=`cat /dbg/pm_debug/smartreflex/2/sr_config_value`
y=$((x + 120))
echo -n $y>/dbg/pm_debug/smartreflex/2/sr_config_value
#and enable it..
echo -n "1" >/sys/power/sr_vdd2_autocomp
Tested on:
SDP3430 with test N values as above and with ES3.1 silicon
TODO:
a) Handle scenarios for multiple OMAP variants with differing
SR capabilities (e.g. varying OPP levels - e.g. 3630, 4430 etc..)
[IMMEDIATE ISSUE]
b) Handling OMAP variants with different tuning values
c) Handling different SR capable PMIC with different tuning values
d) A proper handling of locking mechanism b/w dvfs and userspace access of
sr[x]_vddautocomp
e) A more robust error handling
f) using SR on larger number of boards and any tuning parameters
which may be needed additionally (HS/FS I2C4 ops etc..)
g) Wider testing and and bug fixes
h) Analyse how to use SR decided voltages for OPP1 as retention voltage.
some systems may choose to disable OPP1, what do we do then?
Cc: Rajendra Nayak <rnayak@xxxxxx>
Cc: Roger Quadros <ext-roger.quadros@xxxxxxxxx>
Cc: Kalle Jokiniemi <ext-kalle.jokiniemi@xxxxxxxxx>
Cc: Teerth Reddy <teerth@xxxxxx>
Cc: Kevin Hilman <khilman@xxxxxxxxxxxxxxxxxxx>
Cc: Paul Walmsley <paul@xxxxxxxxx>
Cc: Högander Jouni <jouni.hogander@xxxxxxxxx>
Cc: Mike Chan <mikechan@xxxxxxxxxx>
Signed-off-by: Imberton Guilhem <guilhem.imberton@xxxxxxxxxxxx>
Signed-off-by: Nishanth Menon <nm@xxxxxx>
---
arch/arm/mach-omap2/pm-debug.c | 3 +
arch/arm/mach-omap2/resource34xx.c | 8 +-
arch/arm/mach-omap2/smartreflex.c | 1434 ++++++++++++++++++++++++++++++++++++
arch/arm/mach-omap2/smartreflex.h | 274 +++++++
arch/arm/plat-omap/Kconfig | 15 +-
5 files changed, 1723 insertions(+), 11 deletions(-)
create mode 100644 arch/arm/mach-omap2/smartreflex.c
create mode 100644 arch/arm/mach-omap2/smartreflex.h
diff --git a/arch/arm/mach-omap2/pm-debug.c b/arch/arm/mach-omap2/pm-debug.c
index 5aac64f..1af5e5f 100644
--- a/arch/arm/mach-omap2/pm-debug.c
+++ b/arch/arm/mach-omap2/pm-debug.c
@@ -35,6 +35,7 @@
#include "cm.h"
#include "pm.h"
#include "prm-regbits-34xx.h"
+#include "smartreflex.h"
int omap2_pm_debug;
@@ -617,6 +618,8 @@ static int __init pm_dbg_init(void)
&voltage_off_while_idle,
&pm_dbg_option_fops);
+ (void)sr_debugfs_create_entries(d);
+
pm_dbg_init_done = 1;
return 0;
diff --git a/arch/arm/mach-omap2/resource34xx.c b/arch/arm/mach-omap2/resource34xx.c
index e1a540e..410cb2b 100644
--- a/arch/arm/mach-omap2/resource34xx.c
+++ b/arch/arm/mach-omap2/resource34xx.c
@@ -292,17 +292,23 @@ static int program_opp(int res, struct omap_opp *opp, int target_level,
else
raise = 0;
+#ifdef CONFIG_OMAP_SMARTREFLEX
+ sr_vp_disable_both(t_opp, c_opp);
+#endif
for (i = 0; i < 2; i++) {
if (i == raise)
ret = program_opp_freq(res, target_level,
current_level);
#ifdef CONFIG_OMAP_SMARTREFLEX
else
- sr_voltagescale_vcbypass(t_opp, c_opp,
+ sr_voltage_set(t_opp, c_opp,
opp[target_level].vsel,
opp[current_level].vsel);
#endif
}
+#ifdef CONFIG_OMAP_SMARTREFLEX
+ sr_vp_enable_both(t_opp, c_opp);
+#endif
return ret;
}
diff --git a/arch/arm/mach-omap2/smartreflex.c b/arch/arm/mach-omap2/smartreflex.c
new file mode 100644
index 0000000..b9edfad
--- /dev/null
+++ b/arch/arm/mach-omap2/smartreflex.c
@@ -0,0 +1,1434 @@
+/*
+ * linux/arch/arm/mach-omap3/smartreflex.c
+ *
+ * OMAP34XX SmartReflex Voltage Control
+ *
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ * Nishanth Menon
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Kalle Jokiniemi
+ *
+ * Copyright (C) 2007 Texas Instruments, Inc.
+ * Lesly A M <x0080970@xxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/sysfs.h>
+#include <linux/kobject.h>
+#include <linux/i2c/twl4030.h>
+#include <linux/io.h>
+#include <linux/debugfs.h>
+
+#include <mach/omap34xx.h>
+#include <mach/control.h>
+#include <mach/clock.h>
+#include <mach/omap-pm.h>
+#include <mach/resource.h>
+#include <mach/powerdomain.h>
+
+#include "prm.h"
+#include "smartreflex.h"
+#include "prm-regbits-34xx.h"
+
+/* MCUDISACK is expected to happen within 1uSec. */
+#define COUNT_TIMEOUT_MCUDISACK 200
+
+/* VPINIDLE is expected to happen within 100uSec. Typical is 2uSec */
+#define COUNT_TIMEOUT_VPINIDLE 200
+
+/* Time taken for setting the device - worst case as FS I2C
+ * Depends on SMPSWAITIME MIN/MAX Typical is 200uSec
+ */
+#define COUNT_TIMEOUT_TRANSDONE_SET 400
+
+/* Time to clear out multiple transdone events typical is 3uSec */
+#define COUNT_TIMEOUT_TRANSDONE_CLR 50
+
+/* Time For VCBypass mode for TWL4030 derivative chip. */
+#define COUNT_TIMEOUT_TWL4030_VCBYPASS 500
+
+/* How many retries to do for I2C errors seen on bus for Forceupdate? */
+#define COUNT_RETRY_SMPSNOACK 4
+
+#define SR_REGADDR(offset) (sr->srbase_addr + (offset))
+
+/* Which function to use for setting voltage */
+#ifdef CONFIG_OMAP_VC_BYPASS_UPDATE
+#define SR_CHOSEN_VOLTAGE_UPDATE_MECH sr_vc_bypass
+#else
+#define SR_CHOSEN_VOLTAGE_UPDATE_MECH sr_vp_forceupdate
+#endif
+
+/* Structure for Voltage processor */
+struct omap_sr_vp {
+ /* Store the commonly used register offsets.
+ * this saves a if condition decision
+ */
+ u16 prm_vpx_status_offset;
+ u16 prm_vpx_config_offset;
+ u16 prm_vpx_stepmin_offset;
+ u16 prm_vpx_stepmax_offset;
+ u16 prm_vpx_limito_offset;
+ /* Store the defaults
+ * allowing us to save OCP read
+ * operation
+ */
+ u32 vpconfig_value;
+ u32 vpstepmin_value;
+ u32 vpstepmax_value;
+ u32 vplimito_value;
+ u32 vpenable_mask;
+ u32 irqmask_trans_done;
+ u32 irqmask_smps_noack;
+};
+
+/* Structure for Smart Reflex */
+struct omap_sr {
+ u8 srid;
+ /* SR activity marker */
+ u8 is_sr_reset;
+ u8 is_autocomp_active;
+ u32 req_opp_no;
+ u32 opp_nvalue[5];
+ u32 sr_config_value;
+ u32 sr_errconfig_value;
+ struct clk *fclk;
+ struct clk *iclk;
+ void __iomem *srbase_addr;
+ /* Lock for maintaining SR+VP programming sequence atomicity */
+ /* Voltage processor for the specific SR module */
+ struct omap_sr_vp vp;
+};
+
+/* Smart Reflex 1 structure */
+static struct omap_sr sr1 = {
+ /* *INDENT-OFF* */
+ .srid = SR1,
+ .is_sr_reset = 1,
+ .is_autocomp_active = 0,
+ .srbase_addr = (void *)OMAP34XX_SR1_BASE,
+ .vp = {
+ .prm_vpx_status_offset = OMAP3_PRM_VP1_STATUS_OFFSET,
+ .prm_vpx_config_offset = OMAP3_PRM_VP1_CONFIG_OFFSET,
+ .prm_vpx_stepmin_offset = OMAP3_PRM_VP1_VSTEPMIN_OFFSET,
+ .prm_vpx_stepmax_offset = OMAP3_PRM_VP1_VSTEPMAX_OFFSET,
+ .prm_vpx_limito_offset = OMAP3_PRM_VP1_VLIMITTO_OFFSET,
+ .vpconfig_value = PRM_VP1_CONFIG_ERROROFFSET |
+ PRM_VP1_CONFIG_TIMEOUTEN,
+ .vpstepmin_value = PRM_VP1_VSTEPMIN_SMPSWAITTIMEMIN |
+ PRM_VP1_VSTEPMIN_VSTEPMIN,
+ .vpstepmax_value = PRM_VP1_VSTEPMAX_SMPSWAITTIMEMAX |
+ PRM_VP1_VSTEPMAX_VSTEPMAX,
+ .vplimito_value = PRM_VP1_VLIMITTO_VDDMAX |
+ PRM_VP1_VLIMITTO_VDDMIN,
+ .vpenable_mask = PRM_VP1_CONFIG_VPENABLE,
+ .irqmask_trans_done = VP1_IRQMASK_TRANSDONE,
+ .irqmask_smps_noack = OMAP3430_VP1_NOSMPSACK_ST,
+ },
+ /* *INDENT-ON* */
+};
+
+/* Smart Reflex 2 structure */
+static struct omap_sr sr2 = {
+ /* *INDENT-OFF* */
+ .srid = SR2,
+ .is_sr_reset = 1,
+ .is_autocomp_active = 0,
+ .srbase_addr = (void *)OMAP34XX_SR2_BASE,
+ .vp = {
+ .prm_vpx_status_offset = OMAP3_PRM_VP2_STATUS_OFFSET,
+ .prm_vpx_config_offset = OMAP3_PRM_VP2_CONFIG_OFFSET,
+ .prm_vpx_stepmin_offset = OMAP3_PRM_VP2_VSTEPMIN_OFFSET,
+ .prm_vpx_stepmax_offset = OMAP3_PRM_VP2_VSTEPMAX_OFFSET,
+ .prm_vpx_limito_offset = OMAP3_PRM_VP2_VLIMITTO_OFFSET,
+ .vpconfig_value = PRM_VP2_CONFIG_ERROROFFSET |
+ PRM_VP2_CONFIG_TIMEOUTEN,
+ .vpstepmin_value = PRM_VP2_VSTEPMIN_SMPSWAITTIMEMIN |
+ PRM_VP2_VSTEPMIN_VSTEPMIN,
+ .vpstepmax_value = PRM_VP2_VSTEPMAX_SMPSWAITTIMEMAX |
+ PRM_VP2_VSTEPMAX_VSTEPMAX,
+ .vplimito_value = PRM_VP2_VLIMITTO_VDDMAX |
+ PRM_VP2_VLIMITTO_VDDMIN,
+ .vpenable_mask = PRM_VP2_CONFIG_VPENABLE,
+ .irqmask_trans_done = VP2_IRQMASK_TRANSDONE,
+ .irqmask_smps_noack = OMAP3430_VP1_NOSMPSACK_ST,
+ },
+ /* *INDENT-ON* */
+};
+
+/****************** SMART REFLEX DEBUGFS ENTRIES *************************/
+
+#ifdef __SR_DEBUG
+
+/**
+ * @brief sr_debugfs_set - set variable with value
+ *
+ * @param data - variable pointer
+ * @param val - value to set
+ *
+ * @return - 0
+ */
+static int sr_debugfs_set(void *data, u64 val)
+{
+ u32 *option = data;
+
+ *option = val;
+
+ return 0;
+}
+
+/**
+ * @brief sr_debugfs_get - setup the params
+ *
+ * @param data - variable to set
+ * @param val - value to return
+ *
+ * @return - 0
+ */
+static int sr_debugfs_get(void *data, u64 * val)
+{
+ u32 *option = data;
+
+ *val = *option;
+
+ return 0;
+}
+
+DEFINE_SIMPLE_ATTRIBUTE(sr_debugfs_option_fops, sr_debugfs_get, sr_debugfs_set,
+ "%llu\n");
+
+/**
+ * @brief sr_debugfs_create_entries - create the Smart Reflex entries - called
+ * from pm-debug
+ *
+ * @param d - parent directory tree
+ *
+ * @return 0 if all ok, else returns with error
+ */
+int sr_debugfs_create_entries(struct dentry *d)
+{
+ struct dentry *sr_dir;
+ struct dentry *sr_sub_dir;
+ struct omap_sr *sr_list[] = { &sr1, &sr2 };
+ int count;
+
+ sr_dir = debugfs_create_dir("smartreflex", d);
+ if (IS_ERR(sr_dir))
+ return PTR_ERR(sr_dir);
+ for (count = 0; count < (sizeof(sr_list) / sizeof(struct omap_sr *));
+ count++) {
+ struct omap_sr *sr = sr_list[count];
+ char name[2] = "0";
+ name[0] += sr->srid;
+ sr_sub_dir = debugfs_create_dir(name, sr_dir);
+ if (IS_ERR(sr_sub_dir))
+ continue;
+
+ (void)debugfs_create_file("nvalue_opp1", S_IRUGO | S_IWUGO,
+ sr_sub_dir, &(sr->opp_nvalue[0]),
+ &sr_debugfs_option_fops);
+ (void)debugfs_create_file("nvalue_opp2", S_IRUGO | S_IWUGO,
+ sr_sub_dir, &(sr->opp_nvalue[1]),
+ &sr_debugfs_option_fops);
+ (void)debugfs_create_file("nvalue_opp3", S_IRUGO | S_IWUGO,
+ sr_sub_dir, &(sr->opp_nvalue[2]),
+ &sr_debugfs_option_fops);
+ (void)debugfs_create_file("nvalue_opp4", S_IRUGO | S_IWUGO,
+ sr_sub_dir, &(sr->opp_nvalue[3]),
+ &sr_debugfs_option_fops);
+ (void)debugfs_create_file("nvalue_opp5", S_IRUGO | S_IWUGO,
+ sr_sub_dir, &(sr->opp_nvalue[4]),
+ &sr_debugfs_option_fops);
+ (void)debugfs_create_file("sr_errconfig_value",
+ S_IRUGO | S_IWUGO, sr_sub_dir,
+ &(sr->sr_errconfig_value),
+ &sr_debugfs_option_fops);
+ (void)debugfs_create_file("sr_config_value", S_IRUGO | S_IWUGO,
+ sr_sub_dir, &(sr->sr_config_value),
+ &sr_debugfs_option_fops);
+ (void)debugfs_create_file("vpconfig_value", S_IRUGO | S_IWUGO,
+ sr_sub_dir, &(sr->vp.vpconfig_value),
+ &sr_debugfs_option_fops);
+ (void)debugfs_create_file("vpstepmin_value", S_IRUGO | S_IWUGO,
+ sr_sub_dir, &(sr->vp.vpstepmin_value),
+ &sr_debugfs_option_fops);
+ (void)debugfs_create_file("vpstepmax_value", S_IRUGO | S_IWUGO,
+ sr_sub_dir, &(sr->vp.vpstepmax_value),
+ &sr_debugfs_option_fops);
+ (void)debugfs_create_file("vplimito_value", S_IRUGO | S_IWUGO,
+ sr_sub_dir, &(sr->vp.vplimito_value),
+ &sr_debugfs_option_fops);
+ (void)debugfs_create_file("vplimito_value", S_IRUGO | S_IWUGO,
+ sr_sub_dir, &(sr->vp.vplimito_value),
+ &sr_debugfs_option_fops);
+ }
+
+ return 0;
+}
+
+#endif /* __SR_DEBUG */
+
+/****************** PMIC WEAK FUNCTIONS FOR TWL4030 derivatives **********/
+
+/**
+ * @brief pmic_srinit - Power management IC initialization
+ * for smart reflex. The current code is written for TWL4030
+ * derivatives, replace in board file if PMIC requires
+ * a different sequence
+ *
+ * @return result of operation
+ */
+int __weak __init omap_pmic_srinit(void)
+{
+ int ret = -ENODEV;
+#ifdef CONFIG_TWL4030_CORE
+ u8 reg;
+ /* Enable SR on T2 */
+ ret = twl4030_i2c_read_u8(TWL4030_MODULE_PM_RECEIVER, ®,
+ R_DCDC_GLOBAL_CFG);
+
+ reg |= DCDC_GLOBAL_CFG_ENABLE_SRFLX;
+ ret |= twl4030_i2c_write_u8(TWL4030_MODULE_PM_RECEIVER, reg,
+ R_DCDC_GLOBAL_CFG);
+#endif /* End of CONFIG_TWL4030_CORE */
+ return ret;
+}
+
+/**
+ * @brief omap_pmic_voltage_ramp_delay - how much should this pmic ramp delay
+ * Various PMICs have different ramp up and down delays. choose to implement
+ * in required pmic file to override this function.
+ * On TWL4030 derivatives:
+ * T2 SMPS slew rate (min) 4mV/uS, step size 12.5mV,
+ * 2us added as buffer.
+ *
+ * @param srid - which SR is this for?
+ * @param target_vsel - targetted voltage selction
+ * @param current_vsel - current voltage selection
+ *
+ * @return delay in uSeconds
+ */
+u32 __weak omap_pmic_voltage_ramp_delay(u8 srid, u8 target_vsel,
+ u8 current_vsel)
+{
+ u32 t2_smps_steps = abs(target_vsel - current_vsel);
+ u32 t2_smps_delay = ((t2_smps_steps * 125) / 40) + 2;
+ return t2_smps_delay;
+}
+
+#ifdef CONFIG_OMAP_VC_BYPASS_UPDATE
+/**
+ * @brief omap_pmic_voltage_cmds - hook for pmic command sequence
+ * to be send out which are specific to pmic to set a specific voltage.
+ * this should inturn call vc_send_command with the required sequence
+ * The current implementation is for TWL4030 derivatives
+ *
+ * @param srid - which SR is this for?
+ * @param target_vsel - what voltage is desired to be set?
+ *
+ * @return specific value to set.
+ */
+int __weak omap_pmic_voltage_cmds(u8 srid, u8 target_vsel)
+{
+ u8 reg_addr = (srid == SR1) ? R_VDD1_SR_CONTROL : R_VDD2_SR_CONTROL;
+ u16 timeout = COUNT_TIMEOUT_TWL4030_VCBYPASS;
+ return vc_send_command(R_SRI2C_SLAVE_ADDR, reg_addr, target_vsel,
+ &timeout);
+}
+#endif /* ifdef CONFIG_OMAP_VC_BYPASS_UPDATE */
+
+/*********************** Voltage Controller functions *************************/
+
+/**
+ * @brief vc_send_command - The actual command transmission using
+ * Voltage controller on I2C4
+ *
+ * @param slave_addr - what is the PMIC slave address
+ * @param reg_addr - what is the register address I should be using?
+ * @param data - what value do you want to write here?
+ * @param timeout_us timeout in uSeconds - returns actual time left
+ *
+ * @return 0 if all ok, else error value
+ */
+int vc_send_command(u8 slave_addr, u8 reg_addr, u8 data, u16 *timeout_us)
+{
+ u32 value;
+ u32 count;
+
+ if (unlikely(!timeout_us))
+ return -EINVAL;
+
+ /* timeout = timeout_us/10 -> each udelay event
+ * 1 udelay event every 50 iteration, assuming
+ * each iteration is instaneous,
+ * count = (timeout_us/10) * 50 or timeout_us * 5
+ */
+ count = *timeout_us * 5;
+
+ value = (data << OMAP3430_DATA_SHIFT) |
+ (reg_addr << OMAP3430_REGADDR_SHIFT) |
+ (slave_addr << OMAP3430_SLAVEADDR_SHIFT);
+
+ prm_write_mod_reg(value, OMAP3430_GR_MOD,
+ OMAP3_PRM_VC_BYPASS_VAL_OFFSET);
+
+ value = prm_set_mod_reg_bits(OMAP3430_VALID, OMAP3430_GR_MOD,
+ OMAP3_PRM_VC_BYPASS_VAL_OFFSET);
+ /*
+ * Do continous 50 checks then follow with a 10usec delay,
+ * then check again
+ */
+ do {
+ value = prm_read_mod_reg(OMAP3430_GR_MOD,
+ OMAP3_PRM_VC_BYPASS_VAL_OFFSET)
+ & OMAP3430_VALID;
+ /* should i wait? */
+ if (value && (count % 50))
+ udelay(10);
+ count--;
+ *timeout_us -= 5;
+ } while (value && count);
+ if (!count) {
+ pr_err("VC:Command Timedout! slave_addr=0x%02X,"
+ "reg=0x%02X, value=0x%02X", slave_addr, reg_addr, data);
+ return -ETIMEDOUT;
+ }
+ return 0;
+}
+EXPORT_SYMBOL(vc_send_command);
+
+/**
+ * @brief sr_vc_bypass - setup voltage using VC Bypass technique
+ *
+ * @param target_opp - target opp to go to
+ * @param current_opp - current opp
+ * @param target_vsel - which voltage to go to?
+ * @param current_vsel - current voltage
+ *
+ * @return -success or failure
+ */
+#ifdef CONFIG_OMAP_VC_BYPASS_UPDATE
+static int sr_vc_bypass(struct omap_sr *sr,
+ u32 target_opp_no, u8 target_vsel, u8 current_vsel)
+{
+ int ret = 0;
+ struct omap_sr_vp *vp = &sr->vp;
+ u32 vc_cmd_val_offs;
+ u32 vpconfig_value;
+
+ vc_cmd_val_offs =
+ (sr->srid ==
+ SR1) ? OMAP3_PRM_VC_CMD_VAL_0_OFFSET :
+ OMAP3_PRM_VC_CMD_VAL_1_OFFSET;
+
+ vpconfig_value = vp->vpconfig_value;
+ vpconfig_value |= ((target_opp_no < 3) ? SR_ERRGAIN_LOWOP :
+ SR_ERRGAIN_HIGHOPP) << OMAP3430_ERRORGAIN_SHIFT;
+ vpconfig_value |= target_vsel << OMAP3430_INITVOLTAGE_SHIFT;
+ prm_write_mod_reg(vpconfig_value, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+
+ prm_rmw_mod_reg_bits(OMAP3430_VC_CMD_ON_MASK,
+ (target_vsel << OMAP3430_VC_CMD_ON_SHIFT),
+ OMAP3430_GR_MOD, vc_cmd_val_offs);
+
+ /*
+ * Various PMIC might need a set of commands
+ * provide hooks for specific PMICs to implement
+ */
+ ret = omap_pmic_voltage_cmds(sr->srid, target_vsel);
+
+ /* delay based on pmic */
+ if (!ret)
+ udelay(omap_pmic_voltage_ramp_delay(sr->srid,
+ target_vsel, current_vsel));
+
+ WARN_ON(ret);
+
+ return ret;
+}
+#endif /* ifdef CONFIG_OMAP_VC_BYPASS_UPDATE */
+
+/********************* SR Private functions ***************************/
+
+/**
+ * @brief sr_write_reg - write to Smart Reflex Register
+ *
+ * @param sr - pointer to SR structure
+ * @param offset - SR reg offset to write to
+ * @param value - value to write with
+ */
+static inline void sr_write_reg(struct omap_sr *sr, unsigned offset, u32 value)
+{
+ __raw_writel(value, SR_REGADDR(offset));
+}
+
+/**
+ * @brief sr_modify_reg - Modify a register and write a new value to a field
+ *
+ * @param sr -pointer to SR structure
+ * @param offset -register offset
+ * @param mask -mask to clear out
+ * @param value -value to write there
+ */
+static inline void sr_modify_reg(struct omap_sr *sr, unsigned offset, u32 mask,
+ u32 value)
+{
+ u32 reg_val;
+
+ reg_val = __raw_readl(SR_REGADDR(offset));
+ reg_val &= ~mask;
+ reg_val |= value;
+
+ __raw_writel(reg_val, SR_REGADDR(offset));
+}
+
+/**
+ * @brief sr_read_reg - read a SR register
+ *
+ * @param sr - pointer to SR structure
+ * @param offset - register offset
+ *
+ * @return value in that register
+ */
+static inline u32 sr_read_reg(struct omap_sr *sr, unsigned offset)
+{
+ return __raw_readl(SR_REGADDR(offset));
+}
+
+/**
+ * @brief sr_vplimito_value -return the timeout value based on sysclk
+ * and desired timeout uSec
+ *
+ * @param sys_clk_speed - internal sysclk freq in hz
+ * @param timeout_us - timeout in uSec
+ *
+ * @return timeout value to use in VPLIMITTO:TIMEOUT reg
+ */
+static inline u32 sr_vplimito_value(u32 sys_clk_speed, u16 timeout_us)
+{
+ u32 timeout_val;
+ /* prevent round off errors, we will divide by 10 later */
+ timeout_val = (sys_clk_speed / 100000);
+ timeout_val *= timeout_us;
+ timeout_val /= 10;
+ return timeout_val;
+}
+
+/**
+ * @brief sr_clk_enable - SR clock enable
+ *
+ * @param sr - Structure to SR structure
+ *
+ * @return - result
+ */
+static int sr_clk_enable(struct omap_sr *sr)
+{
+ if (clk_enable(sr->iclk) != 0) {
+ pr_crit("SR:Could not enable %s for [%d]\n",
+ sr->iclk->name, sr->srid);
+ return -EINVAL;
+ }
+ if (clk_enable(sr->fclk) != 0) {
+ pr_crit("SR:Could not enable %s for [%d]\n",
+ sr->fclk->name, sr->srid);
+ clk_disable(sr->iclk);
+ return -EINVAL;
+ }
+ sr_modify_reg(sr, ERRCONFIG,
+ SR_CLKACTIVITY_MASK | ERRCONFIG_INTERRUPT_STATUS_MASK,
+ SR_CLKACTIVITY_IOFF_FON);
+ sr->is_sr_reset = 0;
+
+ return 0;
+}
+
+/**
+ * @brief sr_clk_disable - SR func clock disable
+ *
+ * @param sr - pointer to SR structure
+ */
+static void sr_clk_disable(struct omap_sr *sr)
+{
+ /* set fclk, iclk- idle */
+ sr_modify_reg(sr, ERRCONFIG,
+ SR_CLKACTIVITY_MASK | ERRCONFIG_INTERRUPT_STATUS_MASK,
+ SR_CLKACTIVITY_IOFF_FOFF);
+
+ clk_disable(sr->fclk);
+ clk_disable(sr->iclk);
+ sr->is_sr_reset = 1;
+}
+
+/****************** Voltage processor functions ***************************/
+
+/**
+ * @brief sr_vp_clear_vptransdone - clear vptrans_done event
+ *
+ * @param sr - sr pointer
+ *
+ * @return 0 if cleared ok, else 1 if timedout!
+ */
+static int sr_vp_clear_vptransdone(struct omap_sr *sr)
+{
+ struct omap_sr_vp *vp = &sr->vp;
+ u32 irqstat;
+ u32 count = COUNT_TIMEOUT_TRANSDONE_CLR;
+ do {
+ prm_write_mod_reg(vp->irqmask_trans_done, OCP_MOD,
+ OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+ irqstat = prm_read_mod_reg(OCP_MOD,
+ OMAP3_PRM_IRQSTATUS_MPU_OFFSET) &
+ vp->irqmask_trans_done;
+ if (irqstat)
+ udelay(1);
+ count--;
+ } while (count && irqstat);
+ if (!count) {
+ pr_crit("SR:VPTransdone[%d]:Timedout\n", sr->srid);
+ return -ETIMEDOUT;
+ }
+ return 0;
+}
+
+/**
+ * @brief sr_vp_forceupdate - do a forceupdate method
+ * to update the voltage level
+ *
+ * @param sr - pointer to sr structure
+ * @param target_opp_no - targetted opp number
+ * @param target_vsel - targetted voltage level
+ * @param current_vsel - current voltage level
+ *
+ * @return 0 if all worked out, else 1
+ */
+#ifndef CONFIG_OMAP_VC_BYPASS_UPDATE
+static int sr_vp_forceupdate(struct omap_sr *sr, u32 target_opp_no,
+ u8 target_vsel, u8 current_vsel)
+{
+ u32 count;
+ u32 irqstat;
+ u32 vpconfig_value;
+ u32 retry_counter = COUNT_RETRY_SMPSNOACK;
+
+ struct omap_sr_vp *vp = &sr->vp;
+
+retry_forceupdate:
+ /* First clear any pending events in the system */
+ if (sr_vp_clear_vptransdone(sr)) {
+ pr_crit("SR:forceupdate-transdone1[%d]:timedout\n", sr->srid);
+ return -ETIMEDOUT;
+ }
+
+ vpconfig_value = vp->vpconfig_value;
+ vpconfig_value |= ((target_opp_no < 3) ? SR_ERRGAIN_LOWOP :
+ SR_ERRGAIN_HIGHOPP) << OMAP3430_ERRORGAIN_SHIFT;
+ vpconfig_value |= target_vsel << OMAP3430_INITVOLTAGE_SHIFT;
+
+ prm_write_mod_reg(vpconfig_value, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+
+ /* Trigger initVDD value copy to voltage processor */
+ prm_set_mod_reg_bits(OMAP3430_INITVDD, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+
+ /* Force update of voltage */
+ prm_set_mod_reg_bits(OMAP3430_FORCEUPDATE, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+
+ /* Clear initVDD copy trigger bit */
+ prm_clear_mod_reg_bits(OMAP3430_INITVDD, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+ /* Clear force bit */
+ prm_clear_mod_reg_bits(OMAP3430_FORCEUPDATE, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+
+ /* Now wait for the i2c transactions to complete */
+ count = COUNT_TIMEOUT_TRANSDONE_SET;
+ irqstat = 0;
+ do {
+ irqstat = prm_read_mod_reg(OCP_MOD,
+ OMAP3_PRM_IRQSTATUS_MPU_OFFSET) &
+ vp->irqmask_trans_done;
+ if (!irqstat)
+ udelay(1);
+ count--;
+ } while (count && !irqstat);
+ if (!count) {
+ irqstat = prm_read_mod_reg(OCP_MOD,
+ OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+ if (irqstat & vp->irqmask_smps_noack) {
+ WARN(irqstat, "SMPS NO ACK DETECTED[0x%08X]!!"
+ "ATTEMPTING RECOVERY [%d left]\n",
+ irqstat, retry_counter);
+ prm_write_mod_reg(irqstat, OCP_MOD,
+ OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+ retry_counter--;
+ if (retry_counter)
+ goto retry_forceupdate;
+ }
+ pr_crit("SR:forceupdate-transdone[%d]:timedout-"
+ "irqstat=0x%08X\n", sr->srid, irqstat);
+ BUG();
+ return -ETIMEDOUT;
+ }
+
+ /*
+ * Now we wait for voltage to rise on PMIC
+ */
+ udelay(omap_pmic_voltage_ramp_delay(sr->srid, target_vsel,
+ current_vsel));
+
+ /* clear that event */
+ if (sr_vp_clear_vptransdone(sr)) {
+ pr_crit("SR:forceupdate-transdone2[%d]:timedout\n", sr->srid);
+ BUG();
+ return -ETIMEDOUT;
+ }
+ return 0;
+}
+#endif /* ifndef CONFIG_OMAP_VC_BYPASS_UPDATE */
+
+/**
+ * @brief sr_vp_enable - enable VP enable code
+ *
+ * @param sr
+ */
+static int sr_vp_enable(struct omap_sr *sr, u32 target_opp_no)
+{
+ u32 vpconfig_value;
+ struct omap_sr_vp *vp = &sr->vp;
+
+ /* Disable VP */
+ prm_clear_mod_reg_bits(vp->vpenable_mask, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+ /* Clear INITVDD */
+ prm_clear_mod_reg_bits(OMAP3430_INITVDD, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+
+ vpconfig_value = vp->vpconfig_value;
+ vpconfig_value |= ((sr->srid == SR1) ? mpu_opps[target_opp_no].vsel :
+ l3_opps[target_opp_no].vsel) <<
+ OMAP3430_INITVOLTAGE_SHIFT;
+ vpconfig_value |=
+ ((target_opp_no < 3) ? SR_ERRGAIN_LOWOP : SR_ERRGAIN_HIGHOPP) <<
+ OMAP3430_ERRORGAIN_SHIFT;
+
+ prm_write_mod_reg(vpconfig_value, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+
+ prm_write_mod_reg(vp->vpstepmin_value, OMAP3430_GR_MOD,
+ vp->prm_vpx_stepmin_offset);
+ prm_write_mod_reg(vp->vpstepmax_value, OMAP3430_GR_MOD,
+ vp->prm_vpx_stepmax_offset);
+ prm_write_mod_reg(vp->vplimito_value, OMAP3430_GR_MOD,
+ vp->prm_vpx_limito_offset);
+
+ /* write1 to latch */
+ prm_set_mod_reg_bits(OMAP3430_INITVDD, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+ /* write2 clear */
+ prm_clear_mod_reg_bits(OMAP3430_INITVDD, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+ /* Enable VP */
+ prm_set_mod_reg_bits(vp->vpenable_mask, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+ return 0;
+}
+
+/**
+ * @brief sr_vp_disable - disbale Voltage processor
+ *
+ * @param sr - sr structure
+ *
+ * @return 0 if all ok, else return -ETIMEDOUT
+ */
+static int sr_vp_disable(struct omap_sr *sr)
+{
+ int count;
+ u32 v;
+ struct omap_sr_vp *vp = &sr->vp;
+
+ v = prm_read_mod_reg(OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset) & vp->vpenable_mask;
+ /* Am i already disabled? */
+ if (!v) {
+ pr_info("SR[%d] attempt to disable VP when already disabled!\n",
+ sr->srid);
+ return 0;
+ }
+
+ /* Disable VP */
+ prm_clear_mod_reg_bits(vp->vpenable_mask, OMAP3430_GR_MOD,
+ vp->prm_vpx_config_offset);
+
+ /* Wait for vp to get idle - clear any events pending */
+ count = COUNT_TIMEOUT_MCUDISACK;
+ do {
+ v = prm_read_mod_reg(OMAP3430_GR_MOD,
+ vp->prm_vpx_status_offset) &
+ PRM_VP_STATUS_VPINIDLE;
+ if (!v)
+ udelay(1);
+ count--;
+ } while (count && !v);
+ if (unlikely(!count)) {
+ v = prm_read_mod_reg(OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET);
+ pr_warning("SR:vpdisable-vpinidle[%d][opp=%d]:timedout-"
+ "irqstat=0x%08X\n", sr->srid, sr->req_opp_no, v);
+ return -ETIMEDOUT;
+ }
+ return 0;
+}
+
+/**
+ * @brief sr_vp_configure - configure the basic SR structure
+ *
+ * @param sr - pointer to SR structure
+ */
+static void sr_vp_configure(struct omap_sr *sr)
+{
+ u32 target_opp_no;
+ u32 target_vsel;
+ u32 prm_vpx_voltage;
+
+ if (sr->srid == SR1) {
+ target_opp_no = mpu_opps[resource_get_level("vdd1_opp")].opp_id;
+ target_vsel = mpu_opps[resource_get_level("vdd1_opp")].vsel;
+ prm_vpx_voltage = prm_read_mod_reg(OMAP3430_GR_MOD,
+ OMAP3_PRM_VP1_VOLTAGE_OFFSET);
+ } else {
+ target_opp_no = l3_opps[resource_get_level("vdd2_opp")].opp_id;
+ target_vsel = l3_opps[resource_get_level("vdd2_opp")].vsel;
+ prm_vpx_voltage = prm_read_mod_reg(OMAP3430_GR_MOD,
+ OMAP3_PRM_VP2_VOLTAGE_OFFSET);
+ }
+
+ sr_vp_enable(sr, target_opp_no);
+ if (SR_CHOSEN_VOLTAGE_UPDATE_MECH
+ (sr, target_opp_no, target_vsel, prm_vpx_voltage))
+ pr_crit("SR[%d] CONFIGURE VP failed!!\n", sr->srid);
+}
+
+/**
+ * @brief sr_vp_reset_voltage - reset the voltages back to DVFS values
+ *
+ * @param srid -SRID
+ *
+ * @return 0 if ok, else result
+ */
+static int sr_vp_reset_voltage(u8 srid)
+{
+ u32 target_opp_no;
+ u32 target_vsel;
+ u32 prm_vpx_voltage;
+ struct omap_sr *sr;
+ if (srid == SR1) {
+ sr = &sr1;
+ target_opp_no = sr1.req_opp_no;
+ target_vsel = mpu_opps[target_opp_no].vsel;
+ prm_vpx_voltage = prm_read_mod_reg(OMAP3430_GR_MOD,
+ OMAP3_PRM_VP1_VOLTAGE_OFFSET);
+ } else {
+ sr = &sr2;
+ target_opp_no = sr2.req_opp_no;
+ target_vsel = l3_opps[target_opp_no].vsel;
+ prm_vpx_voltage = prm_read_mod_reg(OMAP3430_GR_MOD,
+ OMAP3_PRM_VP2_VOLTAGE_OFFSET);
+ }
+ return SR_CHOSEN_VOLTAGE_UPDATE_MECH(sr, target_opp_no,
+ target_vsel, prm_vpx_voltage);
+
+}
+
+/*********************** SR functions *************************/
+
+/**
+ * @brief sr_enable - enable smart reflex
+ *
+ * @param sr - smartreflex structure we are interest
+ * @param target_opp_no - target opp we want to switch to
+ *
+ * @return 0 if all went right, else return err val
+ */
+static int sr_enable(struct omap_sr *sr, u32 target_opp_no)
+{
+ u32 value;
+
+ if (!sr->is_sr_reset) {
+ pr_info("SR[%d]already enabled\n", sr->srid);
+ return -EINVAL;
+ }
+
+ sr->req_opp_no = target_opp_no;
+
+ value = sr->opp_nvalue[target_opp_no - 1];
+ if (value == 0) {
+ pr_info("SR[%d]:OPP%d doesn't support SmartReflex\n",
+ sr->srid, target_opp_no);
+ return -EINVAL;
+ }
+
+ sr_clk_enable(sr);
+ /* Start with setting SREnable as 0 */
+ sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0);
+
+ sr_write_reg(sr, SRCONFIG, sr->sr_config_value);
+
+ sr_write_reg(sr, NVALUERECIPROCAL, value);
+
+ value = sr->sr_errconfig_value |
+ ((target_opp_no < 3) ? SR_ERRMINLIMIT_LOWOPP :
+ SR_ERRMINLIMIT_HIGHOPP);
+
+ sr_write_reg(sr, ERRCONFIG, value);
+
+ /* SRCONFIG - enable SR */
+ sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, SRCONFIG_SRENABLE);
+
+ return 0;
+}
+
+/**
+ * @brief sr_disable - disable Smart Reflex
+ *
+ * @param sr - pointer to sr structure of interest
+ *
+ * @return 0 if all went right, else return INVAL/TIMEDOUT
+ */
+int sr_disable(struct omap_sr *sr)
+{
+ int count;
+ u32 stat;
+ u32 value;
+
+ if (sr->is_sr_reset) {
+ pr_info("SR[%d]-disable:already Disabled\n", sr->srid);
+ return -EINVAL;
+ }
+ value = sr_read_reg(sr, SRCONFIG) & SRCONFIG_SRENABLE;
+ if (!value) {
+ pr_info("SR[%d] attempt to disable SR when already disabled!\n",
+ sr->srid);
+ return 0;
+ }
+ value = sr->opp_nvalue[sr->req_opp_no - 1];
+ if (value == 0) {
+ pr_info("SR[%d]-disable:"
+ "OPP%d doesn't support SmartReflex\n",
+ sr->srid, sr->req_opp_no);
+ return -EINVAL;
+ }
+ /* Enable the MCUDISACKINST */
+ sr_modify_reg(sr, ERRCONFIG, ERRCONFIG_MCUDISACKINTEN |
+ ERRCONFIG_INTERRUPT_STATUS_MASK,
+ ERRCONFIG_MCUDISACKINTEN);
+
+ /* SRCONFIG - disable SR */
+ sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0);
+
+ /* Disable VPBOUND interrupt and clear any status
+ * before actually waiting for disack
+ * should be done after sr is disabled
+ */
+ sr_modify_reg(sr, ERRCONFIG, ERRCONFIG_VPBOUNDINTEN |
+ ERRCONFIG_INTERRUPT_STATUS_MASK, ERRCONFIG_VPBOUNDINTST);
+
+ /* Wait for MCUDISACKINTST to be set */
+ count = COUNT_TIMEOUT_MCUDISACK;
+ do {
+ stat = sr_read_reg(sr, ERRCONFIG) & ERRCONFIG_MCUDISACKINTST;
+ if (!stat)
+ udelay(1);
+ count--;
+ } while (count && !stat);
+ /* Clear the event and disable MCUDISACKINST */
+ sr_modify_reg(sr, ERRCONFIG, ERRCONFIG_MCUDISACKINTEN |
+ ERRCONFIG_INTERRUPT_STATUS_MASK,
+ ERRCONFIG_MCUDISACKINTST);
+
+ if (!count) {
+ pr_crit("SR[%d]-disable:MCUDIS timedout\n", sr->srid);
+ return -ETIMEDOUT;
+ }
+ sr_clk_disable(sr);
+ return 0;
+}
+
+/**************** Common enable/disable functionality *********************/
+
+/**
+ * @brief srvp_disable - disable SR and VP
+ * These functions are based on h/w timeouts and should ideally not fail.
+ *
+ * @param sr -sr struct
+ *
+ * @return result
+ */
+static int srvp_disable(struct omap_sr *sr)
+{
+ int ret;
+ /* If we dont have an nvalue, dont bother.. */
+ if (!sr->opp_nvalue[sr->req_opp_no - 1]) {
+ pr_warning("SR[%d]: OPP%d does not support SR to disable\n",
+ sr->srid, sr->req_opp_no);
+ return -EINVAL;
+ }
+ ret = sr_vp_disable(sr);
+ if (unlikely(ret)) {
+ pr_err("SR[%d]: failed to disable vp:%d\n", sr->srid, ret);
+ } else {
+ ret = sr_disable(sr);
+ if (unlikely(ret))
+ pr_err("SR[%d]: failed to disable sr:%d\n",
+ sr->srid, ret);
+ }
+ /*
+ * Does not make much sense renabling SR as
+ * system is going to be in an invalid state
+ */
+ WARN_ON(ret);
+ return ret;
+}
+
+/**
+ * @brief srvp_enable - enable SR and VP
+ * These functions are based on h/w timeouts and should ideally not fail.
+ *
+ * @param sr -sr struct
+ * @param target_opp -opp to go to
+ *
+ * @return result
+ */
+static int srvp_enable(struct omap_sr *sr, u32 target_opp)
+{
+ int ret;
+ /* If we dont have an nvalue, dont bother.. */
+ if (!sr->opp_nvalue[target_opp - 1]) {
+ pr_warning("SR[%d]: OPP%d does not support SR to enable\n",
+ sr->srid, target_opp);
+ return -EINVAL;
+ }
+ ret = sr_vp_enable(sr, target_opp);
+ if (unlikely(ret)) {
+ pr_err("SR[%d]: failed to enable vp:%d\n", sr->srid, ret);
+ } else {
+ ret = sr_enable(sr, target_opp);
+ /* Attempt to recover */
+ if (unlikely(ret)) {
+ pr_err("SR[%d]: failed to enable sr:%d\n", sr->srid,
+ ret);
+ /* nothing we can do if vp_disable fails */
+ (void)sr_vp_disable(sr);
+ }
+ }
+ /*
+ * potentially system in an invalid state - warn..
+ */
+ WARN_ON(ret);
+ return ret;
+}
+
+/*********************** DVFS Entry POINTS **********************************/
+
+/**
+ * @brief sr_vp_enable_both - enable both vp and sr
+ *
+ * @param target_opp - targetted op
+ * @param current_opp - current opp
+ *
+ * @return 0 if ok, 1 if not ok
+ */
+int sr_vp_enable_both(u32 target_opp, u32 current_opp)
+{
+ struct omap_sr *sr;
+ u32 vdd, target_opp_no;
+ int ret = 0;
+
+ vdd = get_vdd(target_opp);
+ target_opp_no = get_opp_no(target_opp);
+ sr = (vdd == PRCM_VDD1) ? &sr1 : &sr2;
+
+ if (sr->is_autocomp_active && sr->is_sr_reset) {
+ ret = srvp_enable(sr, target_opp_no);
+ if (ret) {
+ pr_err("SR[%d]:enableboth:"
+ "failed enable SR\n", sr->srid);
+ }
+ }
+ return 0;
+}
+EXPORT_SYMBOL(sr_vp_enable_both);
+
+/**
+ * @brief sr_vp_disable_both - disable both vp and sr
+ *
+ * @param target_opp - targetted opp
+ * @param current_opp - current opp
+ *
+ * @return 0 if ok, 1 if not ok
+ */
+int sr_vp_disable_both(u32 target_opp, u32 current_opp)
+{
+ struct omap_sr *sr;
+ u32 vdd;
+ int ret = 0;
+
+ vdd = get_vdd(target_opp);
+ sr = (vdd == PRCM_VDD1) ? &sr1 : &sr2;
+
+ if (sr->is_autocomp_active && !sr->is_sr_reset) {
+ ret = srvp_disable(sr);
+ if (ret) {
+ pr_err("SR[%d]:disableboth:"
+ "failed disable SR\n", sr->srid);
+ }
+ }
+
+ return 0;
+
+}
+EXPORT_SYMBOL(sr_vp_disable_both);
+
+/**
+ * @brief sr_voltage_set - setup a voltage requested
+ *
+ * @param target_opp - targetted opp
+ * @param current_opp - current opp
+ * @param target_vsel - targeted voltage
+ * @param current_vsel - current voltage
+ *
+ * @return - result of op -0 if ok, else value
+ */
+int sr_voltage_set(u32 target_opp, u32 current_opp,
+ u8 target_vsel, u8 current_vsel)
+{
+ struct omap_sr *sr;
+ u32 vdd, target_opp_no;
+ int ret;
+
+ vdd = get_vdd(target_opp);
+ target_opp_no = get_opp_no(target_opp);
+ sr = (vdd == PRCM_VDD1) ? &sr1 : &sr2;
+
+ ret =
+ SR_CHOSEN_VOLTAGE_UPDATE_MECH(sr, target_opp_no, target_vsel,
+ current_vsel);
+
+ return ret;
+}
+EXPORT_SYMBOL(sr_voltage_set);
+
+/*********************** CPUIDLE ENTRY POINTS *********************************/
+
+/**
+ * @brief disable_smartreflex - disable SmartReflex before WFI
+ *
+ * @param srid SRID
+ */
+void disable_smartreflex(u8 srid)
+{
+ struct omap_sr *sr = NULL;
+ int ret;
+ u32 current_opp_no;
+
+ /* I want to be in irq_disabled context..
+ * else I will die.. find the rootcause and fix it instead
+ */
+ BUG_ON(!irqs_disabled());
+
+ sr = (srid == SR1) ? &sr1 : &sr2;
+
+ current_opp_no = (sr->srid == SR1) ?
+ mpu_opps[resource_get_level("vdd1_opp")].opp_id :
+ l3_opps[resource_get_level("vdd2_opp")].opp_id;
+
+ if (sr->is_autocomp_active && !sr->is_sr_reset) {
+ sr->req_opp_no = current_opp_no;
+ ret = srvp_disable(sr);
+ if (ret)
+ pr_err("SR[%d]:disable_smartreflex:"
+ "failed disable SR\n", sr->srid);
+ }
+
+ /* Reset the voltage for current OPP to nominal if SR was enabled */
+ if (sr->is_autocomp_active)
+ sr_vp_reset_voltage(srid);
+}
+EXPORT_SYMBOL(disable_smartreflex);
+
+/**
+ * @brief enable_smartreflex - enable smart reflex after WFI is hit
+ *
+ * @param srid -SR ID to hit
+ */
+void enable_smartreflex(u8 srid)
+{
+ struct omap_sr *sr;
+ int ret;
+ u32 current_opp_no;
+
+ /* I want to be in irq_disabled context..
+ * else I will die.. find the rootcause and fix it instead
+ */
+ BUG_ON(!irqs_disabled());
+
+ sr = (srid == SR1) ? &sr1 : &sr2;
+
+ current_opp_no = (sr->srid == SR1) ?
+ mpu_opps[resource_get_level("vdd1_opp")].opp_id :
+ l3_opps[resource_get_level("vdd2_opp")].opp_id;
+ if (sr->is_autocomp_active && sr->is_sr_reset) {
+ ret = srvp_enable(sr, current_opp_no);
+ if (ret)
+ pr_err("SR[%d]:enable_smartreflex:"
+ "failed enable SR\n", sr->srid);
+ }
+}
+EXPORT_SYMBOL(enable_smartreflex);
+
+/*********************** SYSFS ENTRY POINTS *********************************/
+/**
+ * @brief omap_sr_vdd_autocomp_show - Sysfs entry for showing SR status
+ *
+ */
+static ssize_t omap_sr_vdd_autocomp_show(struct kobject *kobj,
+ struct kobj_attribute *attr, char *buf)
+{
+ u8 srid;
+ struct omap_sr *sr;
+ srid = (strcmp(attr->attr.name, "sr_vdd1_autocomp") == 0) ? SR1 : SR2;
+ sr = (srid == SR1) ? &sr1 : &sr2;
+ return sprintf(buf, "%d\n", sr->is_autocomp_active);
+}
+
+/**
+ * @brief omap_sr_vdd_autocomp_store - enable/disable SR
+ *
+ */
+static ssize_t omap_sr_vdd_autocomp_store(struct kobject *kobj,
+ struct kobj_attribute *attr,
+ const char *buf, size_t n)
+{
+ unsigned short value;
+ u8 srid;
+ struct omap_sr *sr;
+ int ret = 0;
+ u32 current_vddopp_no;
+ const char *name;
+
+ name = attr->attr.name;
+
+ srid = (strcmp(name, "sr_vdd1_autocomp") == 0) ? SR1 : SR2;
+ sr = (srid == SR1) ? &sr1 : &sr2;
+ current_vddopp_no = (sr->srid == SR1) ?
+ mpu_opps[resource_get_level("vdd1_opp")].opp_id :
+ l3_opps[resource_get_level("vdd2_opp")].opp_id;
+
+ if (sscanf(buf, "%hu", &value) != 1 || (value > 1)) {
+ pr_err("%s: Invalid value[%d]. Use 0 or 1\n", name, value);
+ return -EINVAL;
+ }
+ if (sr->is_autocomp_active == value) {
+ pr_info("%s: Already set to %d \n", name, value);
+ return n;
+ }
+ /*
+ * Sanity check-might happen if SR and dvfs/idle paths collide
+ * but unlikely though..
+ */
+ if (unlikely(value ^ sr->is_sr_reset)) {
+ pr_warning("%s: Is already set %d Vs %d.\n", name, value,
+ sr->is_sr_reset);
+ return n;
+ }
+
+ if (value)
+ ret = srvp_enable(sr, current_vddopp_no);
+ else {
+ ret = srvp_disable(sr);
+ /* reset the voltage back to nominal */
+ sr_vp_configure(sr);
+ }
+ if (!ret) {
+ sr->is_autocomp_active = value;
+ ret = n;
+ }
+
+ return ret;
+}
+
+static struct kobj_attribute sr_vdd1_autocomp = {
+ .attr = {
+ .name = __stringify(sr_vdd1_autocomp),
+ .mode = 0644,
+ },
+ .show = omap_sr_vdd_autocomp_show,
+ .store = omap_sr_vdd_autocomp_store,
+};
+
+static struct kobj_attribute sr_vdd2_autocomp = {
+ .attr = {
+ .name = __stringify(sr_vdd2_autocomp),
+ .mode = 0644,
+ },
+ .show = omap_sr_vdd_autocomp_show,
+ .store = omap_sr_vdd_autocomp_store,
+};
+
+/*********************** INIT FUNCTIONS *************************************/
+
+/**
+ * @brief srvp_init - configure smart reflex and VP params
+ *
+ * @param sr - structure of sr of interest
+ */
+static void __init srvp_init(struct omap_sr *sr)
+{
+ struct clk *sys_ck;
+ u32 sys_clk_speed;
+ u32 clk_len;
+ u32 senn_mod, senp_mod;
+
+ /* Grab the clock speed */
+ sys_ck = clk_get(NULL, "sys_ck");
+ sys_clk_speed = clk_get_rate(sys_ck);
+ clk_put(sys_ck);
+
+ switch (sys_clk_speed) {
+ case 12000000:
+ clk_len = SRCLKLENGTH_12MHZ_SYSCLK;
+ break;
+ case 13000000:
+ clk_len = SRCLKLENGTH_13MHZ_SYSCLK;
+ break;
+ case 19200000:
+ clk_len = SRCLKLENGTH_19MHZ_SYSCLK;
+ break;
+ case 26000000:
+ clk_len = SRCLKLENGTH_26MHZ_SYSCLK;
+ break;
+ case 38400000:
+ clk_len = SRCLKLENGTH_38MHZ_SYSCLK;
+ break;
+ default:
+ pr_err("SR[%d]:Invalid sysclk value: %d\n", sr->srid,
+ sys_clk_speed);
+ BUG();
+ return;
+ }
+ /* Configure from the nvalues */
+ if (sr->srid == SR1) {
+ senn_mod = (omap_ctrl_readl(OMAP343X_CONTROL_FUSE_SR) &
+ OMAP343X_SR1_SENNENABLE_MASK) >>
+ OMAP343X_SR1_SENNENABLE_SHIFT;
+ senp_mod = (omap_ctrl_readl(OMAP343X_CONTROL_FUSE_SR) &
+ OMAP343X_SR1_SENPENABLE_MASK) >>
+ OMAP343X_SR1_SENPENABLE_SHIFT;
+
+ sr->opp_nvalue[4] =
+ omap_ctrl_readl(OMAP343X_CONTROL_FUSE_OPP5_VDD1);
+ sr->opp_nvalue[3] =
+ omap_ctrl_readl(OMAP343X_CONTROL_FUSE_OPP4_VDD1);
+ sr->opp_nvalue[2] =
+ omap_ctrl_readl(OMAP343X_CONTROL_FUSE_OPP3_VDD1);
+ sr->opp_nvalue[1] =
+ omap_ctrl_readl(OMAP343X_CONTROL_FUSE_OPP2_VDD1);
+ sr->opp_nvalue[0] =
+ omap_ctrl_readl(OMAP343X_CONTROL_FUSE_OPP1_VDD1);
+ sr->sr_errconfig_value = SR1_ERRWEIGHT | SR1_ERRMAXLIMIT;
+ sr->vp.vplimito_value |= sr_vplimito_value(sys_clk_speed,
+ PRM_VP1_VLIMITTO_TIMEOUT_US)
+ << PRM_VP1_VLIMITTO_TIMEOUT_SHIFT;
+
+ } else {
+ senn_mod = (omap_ctrl_readl(OMAP343X_CONTROL_FUSE_SR) &
+ OMAP343X_SR2_SENNENABLE_MASK) >>
+ OMAP343X_SR2_SENNENABLE_SHIFT;
+
+ senp_mod = (omap_ctrl_readl(OMAP343X_CONTROL_FUSE_SR) &
+ OMAP343X_SR2_SENPENABLE_MASK) >>
+ OMAP343X_SR2_SENPENABLE_SHIFT;
+
+ sr->opp_nvalue[2] =
+ omap_ctrl_readl(OMAP343X_CONTROL_FUSE_OPP3_VDD2);
+ sr->opp_nvalue[1] =
+ omap_ctrl_readl(OMAP343X_CONTROL_FUSE_OPP2_VDD2);
+ sr->opp_nvalue[0] =
+ omap_ctrl_readl(OMAP343X_CONTROL_FUSE_OPP1_VDD2);
+ sr->sr_errconfig_value = SR2_ERRWEIGHT | SR2_ERRMAXLIMIT;
+ sr->vp.vplimito_value |= sr_vplimito_value(sys_clk_speed,
+ PRM_VP2_VLIMITTO_TIMEOUT_US)
+ << PRM_VP2_VLIMITTO_TIMEOUT_SHIFT;
+ }
+
+ sr->sr_errconfig_value |=
+ ERRCONFIG_VPBOUNDINTEN | ERRCONFIG_VPBOUNDINTST |
+ SR_CLKACTIVITY_IOFF_FON;
+
+ sr->sr_config_value =
+ (clk_len << SRCONFIG_SRCLKLENGTH_SHIFT) | SRCONFIG_ERRGEN_EN
+ | SRCONFIG_SENENABLE | (senn_mod <<
+ SRCONFIG_SENNENABLE_SHIFT) |
+ (senp_mod << SRCONFIG_SENPENABLE_SHIFT) | SRCONFIG_DELAYCTRL;
+
+ /* Set up nominal voltage */
+ sr_vp_configure(sr);
+}
+
+/**
+ * @brief omap_sr_init - SR initialization
+ *
+ * @return 0
+ */
+static int __init omap_sr_init(void)
+{
+ int ret = 0;
+ ret = omap_pmic_srinit();
+ if (ret) {
+ pr_crit("PMIC init failed during SmartReflex initilization."
+ "connectivity issues?: %d\n", ret);
+ return ret;
+ }
+ /* TODO: Extend this support for various PMICs */
+ if (cpu_is_omap34xx()) {
+ sr1.fclk = clk_get(NULL, "sr1_fck");
+ sr1.iclk = clk_get(NULL, "sr_l4_ick");
+ sr1.srbase_addr = ioremap((u32) sr1.srbase_addr, SZ_4K);
+ sr2.fclk = clk_get(NULL, "sr2_fck");
+ sr2.iclk = clk_get(NULL, "sr_l4_ick");
+ sr2.srbase_addr = ioremap((u32) sr2.srbase_addr, SZ_4K);
+
+ srvp_init(&sr1);
+ srvp_init(&sr2);
+
+ } else {
+ pr_warning("SmartReflex is not supported\n");
+ return -ENODEV;
+ }
+
+ pr_info("SmartReflex driver initialized\n");
+
+ ret = sysfs_create_file(power_kobj, &sr_vdd1_autocomp.attr);
+ if (ret)
+ pr_warning("sysfs_create_file failed: %d\n", ret);
+
+ ret = sysfs_create_file(power_kobj, &sr_vdd2_autocomp.attr);
+ if (ret)
+ pr_warning("sysfs_create_file failed: %d\n", ret);
+
+ return 0;
+}
+
+late_initcall(omap_sr_init);
diff --git a/arch/arm/mach-omap2/smartreflex.h b/arch/arm/mach-omap2/smartreflex.h
new file mode 100644
index 0000000..421f8b6
--- /dev/null
+++ b/arch/arm/mach-omap2/smartreflex.h
@@ -0,0 +1,274 @@
+#ifndef __ARCH_ARM_MACH_OMAP3_SMARTREFLEX_H
+#define __ARCH_ARM_MACH_OMAP3_SMARTREFLEX_H
+/*
+ * linux/arch/arm/mach-omap2/smartreflex.h
+ *
+ * Copyright (C) 2009 Texas Instruments, Inc.
+ * Nishanth Menon
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Kalle Jokiniemi
+ *
+ * Copyright (C) 2007 Texas Instruments, Inc.
+ * Lesly A M <x0080970@xxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* SMART REFLEX REG ADDRESS OFFSET */
+#define SRCONFIG 0x00
+#define SRSTATUS 0x04
+#define SENVAL 0x08
+#define SENMIN 0x0C
+#define SENMAX 0x10
+#define SENAVG 0x14
+#define AVGWEIGHT 0x18
+#define NVALUERECIPROCAL 0x1C
+#define SENERROR 0x20
+#define ERRCONFIG 0x24
+
+/* SR Modules */
+#define SR1 1
+#define SR2 2
+
+#define VP1_IRQMASK_TRANSDONE (0x1 << 15)
+#define VP2_IRQMASK_TRANSDONE (0x1 << 21)
+
+/* PRM_VP1_CONFIG */
+#define PRM_VP1_CONFIG_ERROROFFSET (0x00 << 24)
+#define PRM_VP1_CONFIG_ERRORGAIN (0x18 << 16)
+#define SR_ERRGAIN_LOWOP (0x0C)
+#define SR_ERRGAIN_HIGHOPP (0x18)
+#define SR_ERRMINLIMIT_LOWOPP (0xF4 << 0)
+#define SR_ERRMINLIMIT_HIGHOPP (0xF9 << 0)
+#define PRM_VP_STATUS_VPINIDLE (0x1 << 0)
+
+#define PRM_VP1_CONFIG_INITVOLTAGE (0x30 << 8) /* 1.2 volt */
+#define PRM_VP1_CONFIG_TIMEOUTEN (0x1 << 3)
+#define PRM_VP1_CONFIG_INITVDD (0x1 << 2)
+#define PRM_VP1_CONFIG_FORCEUPDATE (0x1 << 1)
+#define PRM_VP1_CONFIG_VPENABLE (0x1 << 0)
+
+/* PRM_VP1_VSTEPMIN */
+#define PRM_VP1_VSTEPMIN_SMPSWAITTIMEMIN (0x03C << 8)
+#define PRM_VP1_VSTEPMIN_VSTEPMIN (0x01 << 0)
+
+/* PRM_VP1_VSTEPMAX */
+#define PRM_VP1_VSTEPMAX_SMPSWAITTIMEMAX (0x003C << 8)
+#define PRM_VP1_VSTEPMAX_VSTEPMAX (0x08 << 0)
+
+/* PRM_VP1_VLIMITTO */
+#define PRM_VP1_VLIMITTO_VDDMAX (0x44 << 24)
+#define PRM_VP1_VLIMITTO_VDDMIN (0x14 << 16)
+#define PRM_VP1_VLIMITTO_TIMEOUT_US (200)
+#define PRM_VP1_VLIMITTO_TIMEOUT_SHIFT (0)
+
+/* PRM_VP2_CONFIG */
+#define PRM_VP2_CONFIG_ERROROFFSET (0x00 << 24)
+#define PRM_VP2_CONFIG_ERRORGAIN (0x18 << 16)
+
+#define PRM_VP2_CONFIG_INITVOLTAGE (0x30 << 8) /* 1.2 volt */
+#define PRM_VP2_CONFIG_TIMEOUTEN (0x1 << 3)
+#define PRM_VP2_CONFIG_INITVDD (0x1 << 2)
+#define PRM_VP2_CONFIG_FORCEUPDATE (0x1 << 1)
+#define PRM_VP2_CONFIG_VPENABLE (0x1 << 0)
+
+/* PRM_VP2_VSTEPMIN */
+#define PRM_VP2_VSTEPMIN_SMPSWAITTIMEMIN (0x03C << 8)
+#define PRM_VP2_VSTEPMIN_VSTEPMIN (0x01 << 0)
+
+/* PRM_VP2_VSTEPMAX */
+#define PRM_VP2_VSTEPMAX_SMPSWAITTIMEMAX (0x003C << 8)
+#define PRM_VP2_VSTEPMAX_VSTEPMAX (0x08 << 0)
+
+/* PRM_VP2_VLIMITTO */
+#define PRM_VP2_VLIMITTO_VDDMAX (0x42 << 24)
+#define PRM_VP2_VLIMITTO_VDDMIN (0x18 << 16)
+#define PRM_VP2_VLIMITTO_TIMEOUT_US (200)
+#define PRM_VP2_VLIMITTO_TIMEOUT_SHIFT (0)
+
+/* SRCONFIG */
+#define SRCLKLENGTH_12MHZ_SYSCLK 0x3C
+#define SRCLKLENGTH_13MHZ_SYSCLK 0x41
+#define SRCLKLENGTH_19MHZ_SYSCLK 0x60
+#define SRCLKLENGTH_26MHZ_SYSCLK 0x82
+#define SRCLKLENGTH_38MHZ_SYSCLK 0xC0
+
+#define SRCONFIG_SRCLKLENGTH_SHIFT 12
+#define SRCONFIG_SENNENABLE_SHIFT 5
+#define SRCONFIG_SENPENABLE_SHIFT 3
+
+#define SRCONFIG_SRENABLE (0x01 << 11)
+#define SRCONFIG_SENENABLE (0x01 << 10)
+#define SRCONFIG_ERRGEN_EN (0x01 << 9)
+#define SRCONFIG_MINMAXAVG_EN (0x01 << 8)
+
+#define SRCONFIG_DELAYCTRL (0x01 << 2)
+#define SRCONFIG_CLKCTRL (0x00 << 0)
+
+/* NVALUERECIPROCAL */
+#define NVALUERECIPROCAL_SENPGAIN_SHIFT 20
+#define NVALUERECIPROCAL_SENNGAIN_SHIFT 16
+#define NVALUERECIPROCAL_RNSENP_SHIFT 8
+#define NVALUERECIPROCAL_RNSENN_SHIFT 0
+
+/* ERRCONFIG */
+#define SR_CLKACTIVITY_MASK (0x03 << 20)
+#define SR_ERRWEIGHT_MASK (0x07 << 16)
+#define SR_ERRMAXLIMIT_MASK (0xFF << 8)
+#define SR_ERRMINLIMIT_MASK (0xFF << 0)
+
+#define SR_CLKACTIVITY_IOFF_FOFF (0x00 << 20)
+#define SR_CLKACTIVITY_IOFF_FON (0x02 << 20)
+
+#define ERRCONFIG_VPBOUNDINTEN (0x1 << 31)
+#define ERRCONFIG_MCUDISACKINTEN (0x1 << 23)
+
+/* Status Bits */
+#define ERRCONFIG_VPBOUNDINTST (0x1 << 30)
+#define ERRCONFIG_MCUACCUMINTST (0x1 << 28)
+#define ERRCONFIG_MCUVALIDINTST (0x1 << 26)
+#define ERRCONFIG_MCUBOUNDINTST (0x1 << 24)
+#define ERRCONFIG_MCUDISACKINTST (0x1 << 22)
+
+/* WARNING: Ensure all access to errconfig register skips
+ * clearing intst bits to ensure that we dont clear status
+ * bits unwantedly.. esp vpbound
+ */
+#define ERRCONFIG_INTERRUPT_STATUS_MASK (ERRCONFIG_VPBOUNDINTST |\
+ ERRCONFIG_MCUACCUMINTST |\
+ ERRCONFIG_MCUVALIDINTST |\
+ ERRCONFIG_MCUBOUNDINTST |\
+ ERRCONFIG_MCUDISACKINTST | (0X1<<19))
+
+#define SR1_ERRWEIGHT (0x04 << 16)
+#define SR1_ERRMAXLIMIT (0x02 << 8)
+#define SR1_ERRMINLIMIT (0xFA << 0)
+
+#define SR2_ERRWEIGHT (0x04 << 16)
+#define SR2_ERRMAXLIMIT (0x02 << 8)
+#define SR2_ERRMINLIMIT (0xFA << 0)
+
+/* T2 SMART REFLEX */
+#define R_SRI2C_SLAVE_ADDR 0x12
+#define R_VDD1_SR_CONTROL 0x00
+#define R_VDD2_SR_CONTROL 0x01
+
+/* VDDs*/
+#define PRCM_VDD1 1
+#define PRCM_VDD2 2
+
+/*
+ * XXX: These should be removed/moved from here once we have a working DVFS
+ * implementation in place
+ */
+#define PHY_TO_OFF_PM_MASTER(p) (p - 0x36)
+#define PHY_TO_OFF_PM_RECIEVER(p) (p - 0x5b)
+#define PHY_TO_OFF_PM_INT(p) (p - 0x2e)
+
+/* Vmode control */
+#define R_DCDC_GLOBAL_CFG PHY_TO_OFF_PM_RECIEVER(0x61)
+/* R_DCDC_GLOBAL_CFG register, SMARTREFLEX_ENABLE values */
+#define DCDC_GLOBAL_CFG_ENABLE_SRFLX 0x08
+
+/* DEVICE ID/DPLL ID/CLOCK ID: bits 28-31 for OMAP type */
+#define OMAP_TYPE_SHIFT 28
+#define OMAP_TYPE_MASK 0xF
+/* OPP ID: bits: 0-4 for OPP number */
+#define OPP_NO_POS 0
+#define OPP_NO_MASK 0x1F
+/* OPP ID: bits: 5-6 for VDD */
+#define VDD_NO_POS 5
+#define VDD_NO_MASK 0x3
+/* Other IDs: bits 20-27 for ID type */
+/* These IDs have bits 25,26,27 as 1 */
+#define OTHER_ID_TYPE_SHIFT 20
+#define OTHER_ID_TYPE_MASK 0xFF
+
+#define OTHER_ID_TYPE(X) ((X & OTHER_ID_TYPE_MASK) << OTHER_ID_TYPE_SHIFT)
+#define ID_OPP_NO(X) ((X & OPP_NO_MASK) << OPP_NO_POS)
+#define ID_VDD(X) ((X & VDD_NO_MASK) << VDD_NO_POS)
+#define OMAP(X) ((X >> OMAP_TYPE_SHIFT) & OMAP_TYPE_MASK)
+#define get_opp_no(X) ((X >> OPP_NO_POS) & OPP_NO_MASK)
+#define get_vdd(X) ((X >> VDD_NO_POS) & VDD_NO_MASK)
+
+/* XXX: end remove/move */
+
+/* XXX: find more appropriate place for these once DVFS is in place */
+extern u32 current_vdd1_opp;
+extern u32 current_vdd2_opp;
+
+/*
+ * Smartreflex module enable/disable interface.
+ * NOTE: if smartreflex is not enabled from sysfs, these functions will not
+ * do anything.
+ */
+#ifdef CONFIG_OMAP_SMARTREFLEX
+void enable_smartreflex(u8 srid);
+void disable_smartreflex(u8 srid);
+int sr_voltage_set(u32 target_opp, u32 current_opp,
+ u8 target_vsel, u8 current_vsel);
+int sr_vp_disable_both(u32 target_opp, u32 current_opp);
+int sr_vp_enable_both(u32 target_opp, u32 current_opp);
+int vc_send_command(u8 slave_addr, u8 reg_addr, u8 data, u16 *timeout_us);
+int omap_pmic_srinit(void);
+u32 omap_pmic_voltage_ramp_delay(u8 srid, u8 target_vsel, u8 current_vsel);
+#ifdef CONFIG_OMAP_VC_BYPASS_UPDATE
+int omap_pmic_voltage_cmds(u8 srid, u8 target_vsel);
+#endif
+
+#ifdef CONFIG_PM_DEBUG
+#define __SR_DEBUG
+#endif
+
+#else
+static inline void enable_smartreflex(u8 srid)
+{
+}
+
+static inline void disable_smartreflex(u8 srid)
+{
+}
+
+static inline int sr_voltage_set(u32 target_opp, u32 current_opp,
+ u8 target_vsel, u8 current_vsel)
+{
+ return -EINVAL;
+}
+
+static inline int sr_vp_disable_both(u32 target_opp, u32 current_opp)
+{
+ return -EINVAL;
+}
+
+static inline int sr_vp_enable_both(u32 target_opp, u32 current_opp)
+{
+ return -EINVAL;
+}
+
+static inline int vc_send_command(u8 slave_addr, u8 reg_addr, u8 data,
+ u16 *timeout_us)
+{
+ return -EINVAL;
+}
+
+#ifdef CONFIG_OMAP_VC_BYPASS_UPDATE
+static inline int omap_pmic_voltage_cmds(u8 srid, u8 target_vsel)
+{
+ return -EINVAL;
+}
+#endif
+#endif
+
+#ifdef __SR_DEBUG
+int sr_debugfs_create_entries(struct dentry *d);
+#else
+static inline int sr_debugfs_create_entries(struct dentry *d)
+{
+ return -EINVAL;
+}
+#endif
+
+#endif /* __ARCH_ARM_MACH_OMAP3_SMARTREFLEX_H */
diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig
index 2143db5..6a3302c 100644
--- a/arch/arm/plat-omap/Kconfig
+++ b/arch/arm/plat-omap/Kconfig
@@ -81,19 +81,14 @@ config OMAP_SMARTREFLEX
compensation for VDD1 and VDD2, user must write 1 to
/sys/power/sr_vddX_autocomp, where X is 1 or 2.
-config OMAP_SMARTREFLEX_TESTING
- bool "Smartreflex testing support"
+config OMAP_VC_BYPASS_UPDATE
+ bool "Use VC Bypass method of updating voltage"
depends on OMAP_SMARTREFLEX
default n
help
- Say Y if you want to enable SmartReflex testing with SW hardcoded
- NVALUES intead of E-fuse NVALUES set in factory silicon testing.
-
- In some devices the E-fuse values have not been set, even though
- SmartReflex modules are included. Using these hardcoded values set
- in software, one can test the SmartReflex features without E-fuse.
-
- WARNING: Enabling this option may cause your device to hang!
+ Say Y if you would like to use VC Bypass method of
+ update. If this is disabled, the default
+ VP forceupdate method is used.
config OMAP_RESET_CLOCKS
bool "Reset unused clocks during boot"
--
1.6.3.3
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
