Re: MMC_CAP_SDIO_IRQ for omap 3430

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Madhusudhan wrote:
Hi John,

So does the SDIO card interrupt mode work fine now?

If somebody likes to test, my updated patch v2 in attachment. Compile tested only, testing and comments are welcome.

Cheers

Dirk

_____ From: John Rigby [mailto:jcrigby@xxxxxxxxx] Sent: Sunday, October 18, 2009 7:24 PM
To: Woodruff, Richard
Cc: Dirk Behme; Chikkature Rajashekar, Madhusudhan;
linux-mmc@xxxxxxxxxxxxxxx; linux-omap@xxxxxxxxxxxxxxx; Steve Sakoman
Subject: Re: MMC_CAP_SDIO_IRQ for omap 3430

Ok I was going to ask where you found that but I just rechecked the TRM and
there it is in plain site:



When this bit is set to 1, the host controller automatically disables all
the input buffers except the buffer of mmci_dat[1] outside of a transaction
in order to detect asynchronous card interrupt on mmci_dat[1] line and
minimize the leakage current of the buffers.


In my defence, I did search the TRM for every occurance of dat1 but not
dat[1].  Oh well live and learn and forget and repeat.

John

On Sun, Oct 18, 2009 at 6:17 PM, John Rigby <jcrigby@xxxxxxxxx> wrote:
Richard,

MMCHS_CON.CPTL = 1  < Don't disable input buffer on DAT1 after
completion to allow seeing SDIO interrupt>

Sounds exactly like what we need.

Thanks
John

On Sun, Oct 18, 2009 at 5:12 PM, Woodruff, Richard <r-woodruff2@xxxxxx>
wrote:
From: linux-omap-owner@xxxxxxxxxxxxxxx [mailto:linux-omap-
owner@xxxxxxxxxxxxxxx] On Behalf Of Dirk Behme
Sent: Sunday, October 18, 2009 11:45 AM
It would be funny if the TRM was wrong and the CIRQ bit is really
cleared by writing 1 to it.  I'll try that.
A while back I hunted down a few of the bits for this.  Maybe this will
help some.
SYSCONFIG.ENAWAKEUP = 1 < allow ocp wrapper to generate an interrupt to
prcm>
MMCHS_HCTL.IWE = 1 < route wake up to module ocp wrapper>
MMCHS_CON.CPTL = 1  < Don't disable input buffer on DAT1 after completion
to allow seeing SDIO interrupt>
MMCHS_HCTL.IWE
MMCHS_ISE.CIRQ_ENABLE <bit to write to enable interrupt at pin>
MMCHS_STAT<bit to write for clear of SDIO interrupt>
CCCCR - IRQ_ENABLE (think host stack will do this)

Regards,
Richard W.




Subject: [PATCH v2][RFC] OMAP HSMMC: Add SDIO interrupt support
Form: Dirk Behme <dirk.behme@xxxxxxxxxxxxxx>

At the moment, OMAP HSMMC driver supports only SDIO polling, resulting in poor
performance. Add support for SDIO interrupt handling. 

Signed-off-by: Dirk Behme <dirk.behme@xxxxxxxxxxxxxx>
---

Patch against recent omap-linux head "Linux omap got rebuilt from scratch"
274c94b29ee7c53609a756acca974e4742c59559

Compile tested only. Please comment and help testing.

Changes in v2:

- For testing only, hardcode IBG. This should be set only in SDIO and 4-bit
  mode. But how to detect this? mmc_card_sdio(host->mmc->card) doesn't seem
  to work here.

- Additonally, set CTPL. Is this needed for 1-bit mode?

 drivers/mmc/host/omap_hsmmc.c |   44 ++++++++++++++++++++++++++++++++++++------
 1 file changed, 38 insertions(+), 6 deletions(-)

Index: linux-beagle/drivers/mmc/host/omap_hsmmc.c
===================================================================
--- linux-beagle.orig/drivers/mmc/host/omap_hsmmc.c
+++ linux-beagle/drivers/mmc/host/omap_hsmmc.c
@@ -65,6 +65,7 @@
 #define SDVSDET			0x00000400
 #define AUTOIDLE		0x1
 #define SDBP			(1 << 8)
+#define IBG			(1 << 19)
 #define DTO			0xe
 #define ICE			0x1
 #define ICS			0x2
@@ -76,6 +77,7 @@
 #define INT_EN_MASK		0x307F0033
 #define BWR_ENABLE		(1 << 4)
 #define BRR_ENABLE		(1 << 5)
+#define CIRQ_ENABLE		(1 << 8)
 #define INIT_STREAM		(1 << 1)
 #define DP_SELECT		(1 << 21)
 #define DDIR			(1 << 4)
@@ -84,9 +86,11 @@
 #define BCE			(1 << 1)
 #define FOUR_BIT		(1 << 1)
 #define DW8			(1 << 5)
+#define CTPL			(1 << 11)
 #define CC			0x1
 #define TC			0x02
 #define OD			0x1
+#define CIRQ			(1 <<  8)
 #define ERR			(1 << 15)
 #define CMD_TIMEOUT		(1 << 16)
 #define DATA_TIMEOUT		(1 << 20)
@@ -268,12 +272,12 @@ static int omap_hsmmc_context_restore(st
 		OMAP_HSMMC_WRITE(host->base, CON, con | DW8);
 		break;
 	case MMC_BUS_WIDTH_4:
-		OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
+		OMAP_HSMMC_WRITE(host->base, CON, (con | CTPL) & ~DW8);
 		OMAP_HSMMC_WRITE(host->base, HCTL,
 			OMAP_HSMMC_READ(host->base, HCTL) | FOUR_BIT);
 		break;
 	case MMC_BUS_WIDTH_1:
-		OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
+		OMAP_HSMMC_WRITE(host->base, CON, (con | CTPL) & ~DW8);
 		OMAP_HSMMC_WRITE(host->base, HCTL,
 			OMAP_HSMMC_READ(host->base, HCTL) & ~FOUR_BIT);
 		break;
@@ -653,6 +657,15 @@ static irqreturn_t omap_hsmmc_irq(int ir
 	status = OMAP_HSMMC_READ(host->base, STAT);
 	dev_dbg(mmc_dev(host->mmc), "IRQ Status is %x\n", status);
 
+	if (status & CIRQ) {
+		dev_dbg(mmc_dev(host->mmc), "SDIO interrupt");
+		OMAP_HSMMC_WRITE(host->base, IE, OMAP_HSMMC_READ(host->base, IE)
+				 & ~(CIRQ_ENABLE));
+		mmc_signal_sdio_irq(host->mmc);
+		spin_unlock(&host->irq_lock);
+		return IRQ_HANDLED;
+	}
+
 	if (status & ERR) {
 #ifdef CONFIG_MMC_DEBUG
 		omap_hsmmc_report_irq(host, status);
@@ -1166,7 +1179,8 @@ static void omap_hsmmc_set_ios(struct mm
 	case MMC_BUS_WIDTH_4:
 		OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
 		OMAP_HSMMC_WRITE(host->base, HCTL,
-			OMAP_HSMMC_READ(host->base, HCTL) | FOUR_BIT);
+				 OMAP_HSMMC_READ(host->base, HCTL)
+				 | IBG | FOUR_BIT);
 		break;
 	case MMC_BUS_WIDTH_1:
 		OMAP_HSMMC_WRITE(host->base, CON, con & ~DW8);
@@ -1512,6 +1526,24 @@ static int omap_hsmmc_disable_fclk(struc
 	return 0;
 }
 
+static void omap_hsmmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
+{
+	struct omap_hsmmc_host *host = mmc_priv(mmc);
+	u32 ie, ise;
+
+	ise = OMAP_HSMMC_READ(host->base, ISE);
+	ie  = OMAP_HSMMC_READ(host->base, IE);
+
+	if (enable) {
+		OMAP_HSMMC_WRITE(host->base, ISE, ise | CIRQ_ENABLE);
+		OMAP_HSMMC_WRITE(host->base, IE,  ie  | CIRQ_ENABLE);
+	} else {
+		OMAP_HSMMC_WRITE(host->base, ISE, ise & ~CIRQ_ENABLE);
+		OMAP_HSMMC_WRITE(host->base, IE,  ie  & ~CIRQ_ENABLE);
+	}
+
+}
+
 static const struct mmc_host_ops omap_hsmmc_ops = {
 	.enable = omap_hsmmc_enable_fclk,
 	.disable = omap_hsmmc_disable_fclk,
@@ -1519,7 +1551,7 @@ static const struct mmc_host_ops omap_hs
 	.set_ios = omap_hsmmc_set_ios,
 	.get_cd = omap_hsmmc_get_cd,
 	.get_ro = omap_hsmmc_get_ro,
-	/* NYET -- enable_sdio_irq */
+	.enable_sdio_irq = omap_hsmmc_enable_sdio_irq,
 };
 
 static const struct mmc_host_ops omap_hsmmc_ps_ops = {
@@ -1529,7 +1561,7 @@ static const struct mmc_host_ops omap_hs
 	.set_ios = omap_hsmmc_set_ios,
 	.get_cd = omap_hsmmc_get_cd,
 	.get_ro = omap_hsmmc_get_ro,
-	/* NYET -- enable_sdio_irq */
+	.enable_sdio_irq = omap_hsmmc_enable_sdio_irq,
 };
 
 #ifdef CONFIG_DEBUG_FS
@@ -1734,7 +1766,7 @@ static int __init omap_hsmmc_probe(struc
 	mmc->max_seg_size = mmc->max_req_size;
 
 	mmc->caps |= MMC_CAP_MMC_HIGHSPEED | MMC_CAP_SD_HIGHSPEED |
-		     MMC_CAP_WAIT_WHILE_BUSY;
+		     MMC_CAP_WAIT_WHILE_BUSY | MMC_CAP_SDIO_IRQ;
 
 	if (mmc_slot(host).wires >= 8)
 		mmc->caps |= MMC_CAP_8_BIT_DATA;

[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux