Re: [EXTERNAL] Re: [PATCH v5 1/2] dt-bindings: net: Add ICSSG Ethernet

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Rob,

On 11/02/23 00:50, Rob Herring wrote:
> On Fri, Feb 10, 2023 at 05:19:56PM +0530, MD Danish Anwar wrote:
>> From: Puranjay Mohan <p-mohan@xxxxxx>
>>
>> Add a YAML binding document for the ICSSG Programmable real time unit
>> based Ethernet hardware. The ICSSG driver uses the PRU and PRUSS consumer
>> APIs to interface the PRUs and load/run the firmware for supporting
>> ethernet functionality.
>>
>> Signed-off-by: Puranjay Mohan <p-mohan@xxxxxx>
>> Signed-off-by: Md Danish Anwar <danishanwar@xxxxxx>
>> ---
>>  .../bindings/net/ti,icssg-prueth.yaml         | 184 ++++++++++++++++++
>>  1 file changed, 184 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
>>
>> diff --git a/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
>> new file mode 100644
>> index 000000000000..8b860f29ecc0
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/net/ti,icssg-prueth.yaml
>> @@ -0,0 +1,184 @@
>> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/net/ti,icssg-prueth.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Texas Instruments ICSSG PRUSS Ethernet
>> +
>> +maintainers:
>> +  - Md Danish Anwar <danishanwar@xxxxxx>
>> +
>> +description:
>> +  Ethernet based on the Programmable Real-Time
>> +  Unit and Industrial Communication Subsystem.
> 
> Odd line wrap length. It should be 80 chars.
> 

Sure, I will modify it.

>> +
>> +allOf:
>> +  - $ref: /schemas/remoteproc/ti,pru-consumer.yaml#
>> +
>> +properties:
>> +  compatible:
>> +    enum:
>> +      - ti,am654-icssg-prueth  # for AM65x SoC family
>> +
>> +  ti,sram:
>> +    $ref: /schemas/types.yaml#/definitions/phandle
>> +    description:
>> +      phandle to MSMC SRAM node
> 
> I believe we have a standard 'sram' property to point to SRAM nodes 
> assuming this is just mmio-sram or similar.
> 

Yes, we have standard 'sram' property but Krzysztof had asked me to make the
sram property vendor specific in last revision of this series.

>> +
>> +  dmas:
>> +    maxItems: 10
>> +
>> +  dma-names:
>> +    items:
>> +      - const: tx0-0
>> +      - const: tx0-1
>> +      - const: tx0-2
>> +      - const: tx0-3
>> +      - const: tx1-0
>> +      - const: tx1-1
>> +      - const: tx1-2
>> +      - const: tx1-3
>> +      - const: rx0
>> +      - const: rx1
>> +
>> +  ti,mii-g-rt:
>> +    $ref: /schemas/types.yaml#/definitions/phandle
>> +    description: |
>> +      phandle to MII_G_RT module's syscon regmap.
>> +
>> +  ti,mii-rt:
>> +    $ref: /schemas/types.yaml#/definitions/phandle
>> +    description: |
>> +      phandle to MII_RT module's syscon regmap
>> +
>> +  interrupts:
>> +    maxItems: 2
>> +    description: |
> 
> Don't need '|'
> 

Sure, I will drop this.

>> +      Interrupt specifiers to TX timestamp IRQ.
>> +
>> +  interrupt-names:
>> +    items:
>> +      - const: tx_ts0
>> +      - const: tx_ts1
>> +
>> +  ethernet-ports:
>> +    type: object
>> +    additionalProperties: false
>> +
>> +    properties:
>> +      '#address-cells':
>> +        const: 1
>> +      '#size-cells':
>> +        const: 0
>> +
>> +    patternProperties:
>> +      ^port@[0-1]$:
>> +        type: object
>> +        description: ICSSG PRUETH external ports
>> +        $ref: ethernet-controller.yaml#
>> +        unevaluatedProperties: false
>> +
>> +        properties:
>> +          reg:
>> +            items:
>> +              - enum: [0, 1]
>> +            description: ICSSG PRUETH port number
>> +
>> +          interrupts:
>> +            maxItems: 1
>> +
>> +          ti,syscon-rgmii-delay:
>> +            items:
>> +              - items:
>> +                  - description: phandle to system controller node
>> +                  - description: The offset to ICSSG control register
>> +            $ref: /schemas/types.yaml#/definitions/phandle-array
>> +            description:
>> +              phandle to system controller node and register offset
>> +              to ICSSG control register for RGMII transmit delay
>> +
>> +        required:
>> +          - reg
>> +    anyOf:
>> +      - required:
>> +          - port@0
>> +      - required:
>> +          - port@1
>> +
>> +required:
>> +  - compatible
>> +  - ti,sram
>> +  - dmas
>> +  - dma-names
>> +  - ethernet-ports
>> +  - ti,mii-g-rt
>> +  - interrupts
>> +  - interrupt-names
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    /* Example k3-am654 base board SR2.0, dual-emac */
>> +    pruss2_eth: ethernet {
>> +        compatible = "ti,am654-icssg-prueth";
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&icssg2_rgmii_pins_default>;
>> +        ti,sram = <&msmc_ram>;
>> +
>> +        ti,prus = <&pru2_0>, <&rtu2_0>, <&tx_pru2_0>,
>> +                  <&pru2_1>, <&rtu2_1>, <&tx_pru2_1>;
>> +        firmware-name = "ti-pruss/am65x-pru0-prueth-fw.elf",
>> +                        "ti-pruss/am65x-rtu0-prueth-fw.elf",
>> +                        "ti-pruss/am65x-txpru0-prueth-fw.elf",
>> +                        "ti-pruss/am65x-pru1-prueth-fw.elf",
>> +                        "ti-pruss/am65x-rtu1-prueth-fw.elf",
>> +                        "ti-pruss/am65x-txpru1-prueth-fw.elf";
>> +        ti,pruss-gp-mux-sel = <2>,      /* MII mode */
>> +                              <2>,
>> +                              <2>,
>> +                              <2>,      /* MII mode */
>> +                              <2>,
>> +                              <2>;
>> +        dmas = <&main_udmap 0xc300>, /* egress slice 0 */
>> +               <&main_udmap 0xc301>, /* egress slice 0 */
>> +               <&main_udmap 0xc302>, /* egress slice 0 */
>> +               <&main_udmap 0xc303>, /* egress slice 0 */
>> +               <&main_udmap 0xc304>, /* egress slice 1 */
>> +               <&main_udmap 0xc305>, /* egress slice 1 */
>> +               <&main_udmap 0xc306>, /* egress slice 1 */
>> +               <&main_udmap 0xc307>, /* egress slice 1 */
>> +               <&main_udmap 0x4300>, /* ingress slice 0 */
>> +               <&main_udmap 0x4301>; /* ingress slice 1 */
>> +        dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
>> +                    "tx1-0", "tx1-1", "tx1-2", "tx1-3",
>> +                    "rx0", "rx1";
>> +        ti,mii-g-rt = <&icssg2_mii_g_rt>;
>> +        interrupt-parent = <&icssg2_intc>;
>> +        interrupts = <24 0 2>, <25 1 3>;
>> +        interrupt-names = "tx_ts0", "tx_ts1";
>> +        ethernet-ports {
>> +            #address-cells = <1>;
>> +            #size-cells = <0>;
>> +            pruss2_emac0: port@0 {
>> +                reg = <0>;
>> +                phy-handle = <&pruss2_eth0_phy>;
>> +                phy-mode = "rgmii-id";
>> +                interrupts-extended = <&icssg2_intc 24>;
>> +                ti,syscon-rgmii-delay = <&scm_conf 0x4120>;
>> +                /* Filled in by bootloader */
>> +                local-mac-address = [00 00 00 00 00 00];
>> +            };
>> +
>> +            pruss2_emac1: port@1 {
>> +                reg = <1>;
>> +                phy-handle = <&pruss2_eth1_phy>;
>> +                phy-mode = "rgmii-id";
>> +                interrupts-extended = <&icssg2_intc 25>;
>> +                ti,syscon-rgmii-delay = <&scm_conf 0x4124>;
>> +                /* Filled in by bootloader */
>> +                local-mac-address = [00 00 00 00 00 00];
>> +            };
>> +        };
>> +    };
>> -- 
>> 2.25.1
>>

-- 
Thanks and Regards,
Danish.



[Index of Archives]     [Linux Arm (vger)]     [ARM Kernel]     [ARM MSM]     [Linux Tegra]     [Linux WPAN Networking]     [Linux Wireless Networking]     [Maemo Users]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite Trails]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux