Hi Thierry, On 01/04/20 1:40 AM, Thierry Reding wrote: > On Tue, Mar 31, 2020 at 08:59:47PM +0530, Lokesh Vutla wrote: >> Hi Thierry, >> >> On 30/03/20 7:44 PM, Thierry Reding wrote: >>> On Thu, Mar 12, 2020 at 07:40:42AM +0100, Uwe Kleine-König wrote: >>>> On Thu, Mar 12, 2020 at 09:52:09AM +0530, Lokesh Vutla wrote: >>>>> Only the Timer control register(TCLR) cannot be updated when the timer >>>>> is running. Registers like Counter register(TCRR), loader register(TLDR), >>>>> match register(TMAR) can be updated when the counter is running. Since >>>>> TCLR is not updated in pwm_omap_dmtimer_config(), do not stop the >>>>> timer for period/duty_cycle update. >>>> >>>> I'm not sure what is sensible here. Stopping the PWM for a short period >>>> is bad, but maybe emitting a wrong period isn't better. You can however >>>> optimise it if only one of period or duty_cycle changes. >>>> >>>> @Thierry, what is your position here? I tend to say a short stop is >>>> preferable. >>> >>> It's not clear to me from the above description how exactly the device >>> behaves, but I suspect that it may latch the values in those registers >>> and only update the actual signal output once a period has finished. I >>> know of a couple of other devices that do that, so it wouldn't be >>> surprising. >>> >>> Even if that was not the case, I think this is just the kind of thing >>> that we have to live with. Sometimes it just isn't possible to have all >>> supported devices adhere strictly to an API. So I think the best we can >>> do is have an API that loosely defines what's supposed to happen and >>> make a best effort to implement those semantics. If a device deviates >>> slightly from those expectations, we can always cross fingers and hope >>> that things still work. And it looks like they are. >>> >>> So I think if Lokesh and Tony agree that this is the right thing to do >>> and have verified that things still work after this, that's about as >>> good as it's going to get. >> >> Yes this is needed especially in the use-case[0] that I am trying to enable >> using PWM. In this case PWM cannot be stopped in between and needs to be updated >> dynamically. Also hardware doesn't provide any restrictions on updating the >> period. So IMHO, this might be the right thing to do. >> >> Tony did provide tested-by and I measured PWM signals on scope with these >> changes. Let me know if any thing else is required? >> >> [0] https://sourceforge.net/p/linuxptp/mailman/message/36943248/ > > From you measurements, can you tell whether or not the signal actually > gets updated in the middle of a period, or does it only get updated at > the end of a full period? There is a corner case where period/duty-cycle gets updated in the middle of the cycle. So let me give more details on how it works: OMAP dual-mode timers with a upward timer counter, can be configured in PWM mode. When the timer counter overflows it gets reloaded with the load value(Load register) and the pwm output goes up. When counter matches with match register, the output goes down. So the load register is used to calculate the period and similarly match register for duty cycle. When PWM is running and changing both duty cycle and period, we cannot prevent in software that the output might produce a period with mixed settings. Especially when the PWM signal is high the following cases can happen: 1) When signal is high and new match value is > current timer counter. Then the duty cycle gets reflected in the current cycle.(Duty_cycle for current period= new match value - previous load value). 2) When signal is high and new match value is < current timer counter. Then the period and duty cycle for the current cycle gets effected as well. Because the signal is pulled down only when counter matches with match register, and this happens only in the next cycle(after timer counter overflows). Then: - new Period for current cycle = (current period + new period) - new duty cycle for current cycle = (current period + new duty_cycle). Rest all the cases the values gets reflected in the next cycle. As advised by Uwe, I have updated all these details in driver. Thanks and regards, Lokesh
